Enhancing mechanical properties of chitosan/PVA electrospun nanofibers: a comprehensive review

• Nur Areisman Mohd Salleh,
• Amalina Muhammad Afifi,
• Fathiah Mohamed Zuki and
• Hanna Sofia SalehHudin

Beilstein J. Nanotechnol. 2025, 16, 286–307, doi:10.3762/bjnano.16.22

• blending of functional agents in the polymer solution, wet chemical methods, surface graft polymerization, and plasma treatment [160]. Low-temperature plasma offers advantages over other techniques in terms of lower energy consumption, faster processing, and minimal solvent use [161]. By appropriately

• , wet chemical procedures, low-temperature plasma treatment, and co-electrospinning with surface-active chemicals and polymers [160]. Among these methods, low-temperature plasma treatment is particularly popular because it can modify the surface properties of the nanofibers without affecting their bulk

• chitosan dissolved in acetic acid in a 1:4 ratio. The solution was electrospun into nanofibers, and plasma treatment was carried out using DBD plasma with O2 gas. The treated electrospun nanofiber exhibited a 15.6% increase in tensile strength and a 37.3% increase in modulus. This phenomenon can be

Hierarchically patterned polyurethane microgrooves featuring nanopillars or nanoholes for neurite elongation and alignment

• Lester Uy Vinzons,
• Guo-Chung Dong and
• Shu-Ping Lin

Beilstein J. Nanotechnol. 2023, 14, 1157–1168, doi:10.3762/bjnano.14.96

• increase in CA on the nanopillar and nanohole substrates may be due to either a Wenzel- or a Cassie-type of wetting [22]. To improve wetting on the substrates, we treated our samples with mild O2 plasma before laminin incubation. After plasma treatment, all samples became hydrophilic (CA < 80°), with the

• the fluorescence patterns conforming to the structure shapes. Laminin was also successfully coated on the flat areas surrounding the pillars and holes, as shown in the corresponding confocal slices in Supporting Information File 1, Figure S5. O2 plasma treatment of PU enables strong laminin adsorption

• ), indicating dominance of the nanostructure properties in this direction. In contrast, the CA values were higher and remained quite close to each other in magnitude even after O2 plasma treatment, signifying the dominance of the microgroove properties in this orientation. Despite the relatively high CA

Effects of focused electron beam irradiation parameters on direct nanostructure formation on Ag surfaces

• Jānis Sniķeris,
• Vjačeslavs Gerbreders,
• Andrejs Bulanovs and
• Ēriks Sļedevskis

Beilstein J. Nanotechnol. 2022, 13, 1004–1010, doi:10.3762/bjnano.13.87

• , radiolysis by collisions with electrons seeming like the most obvious one. It should be noted that N plasma treatment in this case also affected the clean Ag surface, turning it into an interfering thin film. We believe that controlled etching with plasma has the potential to explore the structure of metal

Micro- and nanotechnology in biomedical engineering for cartilage tissue regeneration in osteoarthritis

• Zahra Nabizadeh,
• Mahmoud Nasrollahzadeh,
• Hamed Daemi,
• Mohamadreza Baghaban Eslaminejad,
• Ali Akbar Shabani,
• Mehdi Dadashpour,
• Majid Mirmohammadkhani and
• Davood Nasrabadi

Beilstein J. Nanotechnol. 2022, 13, 363–389, doi:10.3762/bjnano.13.31

• example, to modify the surface of nanofiber polymers, plasma treatment has been used to provide them with hydroxy, carboxyl, or amine polar groups to improve physical properties such as wettability, polarity, and bioadhesion [102]. As a result, surface-modified nanofibers will more likely absorb bioactive

• , and OH) and surface roughness to CNT, Antonioli et al. used oxygen plasma treatment and fabricated novel superhydrophilic VA–CTN films. This treatment could increase the wettability of the nanofilms to acquire appreciable cytocompatibility [134]. The chondrocytes expressed major chondrogenic markers

The effect of metal surface nanomorphology on the output performance of a TENG

• Yiru Wang,
• Xin Zhao,
• Yang Liu and
• Wenjun Zhou

Beilstein J. Nanotechnol. 2022, 13, 298–312, doi:10.3762/bjnano.13.25

• , such as template forming, plasma treatment, and chemical approaches. Previous studies mostly focused on the preparation process of the nanoscale morphology on the polymer surface [47][48][49]. The electrons on the polymer surface cannot be transferred to the conduction band and the charge cannot flow

Sputtering onto liquids: a critical review

• Anastasiya Sergievskaya,
• Adrien Chauvin and
• Stephanos Konstantinidis

Beilstein J. Nanotechnol. 2022, 13, 10–53, doi:10.3762/bjnano.13.2

A review of defect engineering, ion implantation, and nanofabrication using the helium ion microscope

• Frances I. Allen

Beilstein J. Nanotechnol. 2021, 12, 633–664, doi:10.3762/bjnano.12.52

Nanoporous and nonporous conjugated donor–acceptor polymer semiconductors for photocatalytic hydrogen production

• Zhao-Qi Sheng,
• Yu-Qin Xing,
• Yan Chen,
• Guang Zhang,
• Shi-Yong Liu and
• Long Chen

Beilstein J. Nanotechnol. 2021, 12, 607–623, doi:10.3762/bjnano.12.50

• enhanced with increasing the content of FSO units. P66 achieved an AQY of 8.5%. Cooper et al. [82] systematically investigated the influence of plasma treatments on conjugated polymers as photocatalysts, for example, the fluorine–FSO-based P60 (Figure 8). For P60, a short time of plasma treatment

Hexagonal boron nitride: a review of the emerging material platform for single-photon sources and the spin–photon interface

• Stefania Castelletto,
• Faraz A. Inam,
• Shin-ichiro Sato and
• Alberto Boretti

Beilstein J. Nanotechnol. 2020, 11, 740–769, doi:10.3762/bjnano.11.61

Multiwalled carbon nanotube based aromatic volatile organic compound sensor: sensitivity enhancement through 1-hexadecanethiol functionalisation

• Nadra Bohli,
• Meryem Belkilani,
• Juan Casanova-Chafer,
• Eduard Llobet and
• Adnane Abdelghani

Beilstein J. Nanotechnol. 2019, 10, 2364–2373, doi:10.3762/bjnano.10.227

• spectra of Au-MWCNT and SAMs/Au-MWCNT layers, we found common bands and peaks associated with the carbonyl, carboxyl and hydroxyl groups attached to the MWCNT side walls during the oxygen plasma treatment. We also found common bands and peaks associated with the C–H bonds present in both layers. The

Atomic force acoustic microscopy reveals the influence of substrate stiffness and topography on cell behavior

• Yan Liu,
• Li Li,
• Xing Chen,
• Ying Wang,
• Meng-Nan Liu,
• Jin Yan,
• Liang Cao,
• Lu Wang and
• Zuo-Bin Wang

Beilstein J. Nanotechnol. 2019, 10, 2329–2337, doi:10.3762/bjnano.10.223

• treatments have been reported to support the cell spreading [36], the small changes observed here may be due to the littleness of the surface modifications. A recent study documents that protein coating or oxygen plasma treatment of substrate surfaces may influence the phenotypic equilibrium of cells [37

Nanostructured and oriented metal–organic framework films enabling extreme surface wetting properties

• Andre Mähringer,
• Julian M. Rotter and
• Dana D. Medina

Beilstein J. Nanotechnol. 2019, 10, 1994–2003, doi:10.3762/bjnano.10.196

• example, sol–gel synthesis, electrochemical deposition, anodization, electrochemical polymerization, electrospinning, plasma treatment, chemical or hydrothermal methods, vapor deposition, layer-by-layer assembly or laser ablation [19][27][28][29][30][31][32][33][34][35][36][37][38][39]. However, the

Fabrication and characterization of Si_1−xGe_x nanocrystals in as-grown and annealed structures: a comparative study

• Muhammad Taha Sultan,
• Adrian Valentin Maraloiu,
• Ionel Stavarache,
• Jón Tómas Gudmundsson,
• Andrei Manolescu,
• Valentin Serban Teodorescu,
• Magdalena Lidia Ciurea and
• Halldór Gudfinnur Svavarsson

Beilstein J. Nanotechnol. 2019, 10, 1873–1882, doi:10.3762/bjnano.10.182

• in H2/N2 ambient. This results in the passivation of Pb-type defects, dangling bonds and oxide fixed charges, increasing the overall sensitivity of the structure. However, the passivation of structures via plasma treatment showed a much better result in terms of increasing spectral sensitivity than

Tuning the performance of vanadium redox flow batteries by modifying the structural defects of the carbon felt electrode

• Ditty Dixon,
• Deepu Joseph Babu,
• Aiswarya Bhaskar,
• Hans-Michael Bruns,
• Joerg J. Schneider,
• Frieder Scheiba and
• Helmut Ehrenberg

Beilstein J. Nanotechnol. 2019, 10, 1698–1706, doi:10.3762/bjnano.10.165

• )-based carbon felt was subjected to N2-plasma treatment to increase the heteroatom defects and reactive edge sites as a method to increase the performance in vanadium redox flow batteries (VRFBs). N-doping in the felt was mainly in the form of pyrrolic and pyridinic nitrogen. Even though the amount of

• treatment process is quick, and subsequent physical or chemical changes incurred will be uniform across the felt. Apart from that, it is observed that the surface area of the material is not affected by the plasma treatment process. Results and Discussion In this work, the N2 plasma treatment process is

• applied to PAN-based felts to increase the amount of defects. The normalized spectra obtained for the Raman measurements are shown in Figure 1. In order to investigate the degree of graphitization and defects formed during the plasma treatment process, the intensity of the G- and D-band centered at 1590

Direct growth of few-layer graphene on AlN-based resonators for high-sensitivity gravimetric biosensors

• Jimena Olivares,
• Teona Mirea,
• Lorena Gordillo-Dagallier,
• Bruno Marco,
• José Miguel Escolano,
• Marta Clement and
• Enrique Iborra

Beilstein J. Nanotechnol. 2019, 10, 975–984, doi:10.3762/bjnano.10.98

• graphene appears to be more appropriate for the covalent functionalization scheme based on the generation of defects (COOH groups) through a plasma treatment. In this work, we demonstrate that few-layer graphene can be grown directly on top of SMR-type acoustic resonators without a noticeable degradation

• antibodies. The second functionalization method is the direct non-covalent binding of streptavidin to the hydrophobic bare graphene surfaces (no plasma treatment is performed) to which the biotinylated IgG antibodies were bond. IgG antibodies were chosen as a typical antibody although any other biotinylated

• reactive species were able to reach the graphene surface by efficient diffusion through the gas discharge [22]. The process parameters were previously optimized (50 W, 25 mTorr and 25 sccm O2 flow for our system). The samples were characterized by Raman spectroscopy before and after each plasma treatment

Hydrophilicity and carbon chain length effects on the gas sensing properties of chemoresistive, self-assembled monolayer carbon nanotube sensors

• Juan Casanova-Cháfer,
• Carla Bittencourt and
• Eduard Llobet

Beilstein J. Nanotechnol. 2019, 10, 565–577, doi:10.3762/bjnano.10.58

• oxygen plasma treatment. However, the presence of such defects in CNTs is essential, since it has been shown that they play the role of nucleation centers and help to anchor the Au nanoparticles during the sputtering process [36]. In other words, the defects help to achieve a dense and homogenous

• nucleation centers for the anchoring the Au NPs) was conducted using XPS. The chemical modification caused by the plasma treatment results in the presence of hydroxy, carbonyl and carboxyl groups [36]. Furthermore, Au nucleation centers occur mainly in the proximity of oxygenated defects created during the

• plasma treatment [37]. These results are summarized in Supporting Information File 1, Figure S4 and Table S1. The presence of thiols attached to Au NPs was further confirmed by XPS analysis. Figure 4a shows the comparison of the XPS survey spectra recorded on the samples and a reference (gold on CNTs

Geometrical optimisation of core–shell nanowire arrays for enhanced absorption in thin crystalline silicon heterojunction solar cells

• Robin Vismara,
• Olindo Isabella,
• Andrea Ingenito,
• Fai Tong Si and
• Miro Zeman

Beilstein J. Nanotechnol. 2019, 10, 322–331, doi:10.3762/bjnano.10.31

• , was first coated onto the front surface of the wafer on which the nanowires were distributed. Following a hydrogen-plasma treatment, highly transparent boron-doped hydrogenated nanocrystalline silicon oxide (nc-SiOx(p):H) with 30 nm equivalent thickness was deposited on a-Si:H. For the front electrode

Controlling surface morphology and sensitivity of granular and porous silver films for surface-enhanced Raman scattering, SERS

• Sherif Okeil and
• Jörg J. Schneider

Beilstein J. Nanotechnol. 2018, 9, 2813–2831, doi:10.3762/bjnano.9.263

• . Altogether this work shows for the first time the effectiveness of a plasma treatment for surface roughening of silver thin films and its profound influence on the interface-controlled SERS enhancement effect. The method can be used for low-cost, large-scale production of SERS substrates. Keywords: plasma

• ][60]. Recently, other methods emerged with the aim of producing SERS substrates at low cost, enabling their large-scale production. These methods include inkjet-printing and pen-on-paper approaches [61][62]. Plasma treatment has been widely used for the last decades for microelectronics and surface

• , it enables a quick chemical modification under ambient conditions in the gas phase [64][66][67][68][69][70][71]. Thus, plasma treatment could present a straightforward and affordable alternative to the electrochemical roughening of silver and can be even used as a technological reliable alternative

Exploring the photoleakage current and photoinduced negative bias instability in amorphous InGaZnO thin-film transistors with various active layer thicknesses

• Dapeng Wang and
• Mamoru Furuta

Beilstein J. Nanotechnol. 2018, 9, 2573–2580, doi:10.3762/bjnano.9.239

• annealing and N2O plasma treatment [31]; and (ii) inactivating the defects in the semiconductor by means of introducing new elements to form stable chemical bonds with the defects, for example by fluoride ion implantation and nitrogen annealing [32][33]. Conclusion The impact of the TIGZO on the

High-throughput micro-nanostructuring by microdroplet inkjet printing

• Hendrikje R. Neumann and
• Christine Selhuber-Unkel

Beilstein J. Nanotechnol. 2018, 9, 2372–2380, doi:10.3762/bjnano.9.222

• BCML micro-nanostructuring strategies is the time for the patterning itself – it is much shorter and less complicated than other approaches that employ additional steps such as electron-beam lithography or photolithography [20][21]. A further result of the plasma treatment could be a rough surface

• , which has been reported both for Si, SiO2 and NiTi [29][30]. However, as the plasma treatment takes place after the inkjet printing process, a change in roughness will not influence the droplet size, but might influence further functionalization steps. The droplet boundary description was set in the

• Ar/H2 plasma etching at 300 W for 1 h. An exemplary quasi-hexagon pattern is drawn (yellow) for visualization. (B) Inkjet-printed 4 × 4 droplet pattern after drying and Ar/H2 plasma treatment at 300 W for 1 h. Both images were recorded with SEM. SEM images of size and droplet shape on the five

Filling nanopipettes with apertures smaller than 50 nm: dynamic microdistillation

• Evelyne Salançon and
• Bernard Tinland

Beilstein J. Nanotechnol. 2018, 9, 2181–2187, doi:10.3762/bjnano.9.204

• nanopipette, especially the translocation of objects, can introduce undesired microfluidic inhomogeneities, even contributing to aperture clogging. The fourth method, plasma treatment, involves improving the wettability by hydrophilizing the glass surface in an O2 plasma [8][9]. Zweifel et al. [8] observed

• , without filaments. They were filled, without plasma treatment and using a simple method. This nanopipette filling process is usable for all types of nanopipettes. Details of some are provided in this paper, together with the method and reproducible electrical measurements to prove complete filling

Electrospun one-dimensional nanostructures: a new horizon for gas sensing materials

• Muhammad Imran,
• Nunzio Motta and
• Mahnaz Shafiei

Beilstein J. Nanotechnol. 2018, 9, 2128–2170, doi:10.3762/bjnano.9.202

Self-assembled quasi-hexagonal arrays of gold nanoparticles with small gaps for surface-enhanced Raman spectroscopy

• Emre Gürdal,
• Simon Dickreuter,
• Fatima Noureddine,
• Pascal Bieschke,
• Dieter P. Kern and
• Monika Fleischer

Beilstein J. Nanotechnol. 2018, 9, 1977–1985, doi:10.3762/bjnano.9.188

• feasible to obtain quasi-hexagonally ordered regular arrays of gold nanoparticles over large areas by simple means. For the fabrication of gold nanoparticles gold salts can be used to load the micelle core, and the copolymer can be removed afterwards with an oxygen plasma treatment [18][19][20]. For tuning

• ) chloride (KAuCl4, 0.1 wt %, Sigma-Aldrich), to grow the gold precursor particles with the electroless deposition process. Reactive ion etching (Oxford Plasmalab 80 Plus) was used to remove the polymer with an oxygen plasma treatment with the following settings: process pressure 100 mTorr, power 100 W

• with a quartz glass slide (Figure 1b). In a third step the nanoparticles are enlarged by electroless deposition (Figure 1c), and finally the polymer is removed by an oxygen plasma treatment (Figure 1d). SEM images of the primary distribution of the gold precursor particles without any size increase by

Interaction-tailored organization of large-area colloidal assemblies

• Silvia Rizzato,
• Elisabetta Primiceri,
• Anna Grazia Monteduro,
• Adriano Colombelli,
• Angelo Leo,
• Maria Grazia Manera,
• Roberto Rella and
• Giuseppe Maruccio

Beilstein J. Nanotechnol. 2018, 9, 1582–1593, doi:10.3762/bjnano.9.150

• . Successively, reactive ion etching was used to selectively remove the portion of the gold film not protected by the nanospheres. The etch rate (2.9 nm/min) was estimated measuring the thickness of the gold film for different etching times. Finally, the nanosphere residues were removed by oxygen plasma

• treatment for 90 s, revealing the fabricated nanostructures on the substrates. The morphology of the obtained patterns was imaged by means of a scanning electron microscope (SEM, Carl Zeiss) at an accelerating voltage of 5 kV. SEM images were acquired through an in-lens detector for secondary electrons in

Preparation and morphology-dependent wettability of porous alumina membranes

• Dmitry L. Shimanovich,
• Alla I. Vorobjova,
• Daria I. Tishkevich,
• Alex V. Trukhanov,
• Maxim V. Zdorovets and
• Artem L. Kozlovskiy

Beilstein J. Nanotechnol. 2018, 9, 1423–1436, doi:10.3762/bjnano.9.135

• possible to make membranes with hydrophilic properties, combining different methods of barrier layer etching. With the assistance of plasma treatment, the contact angle could be reduced by three times from 93.97° to 31.15° (see Table 2). According to our results, it is possible to assume that the Cassie