Experimental and theoretical study of field-dependent spin splitting at ferromagnetic insulator–superconductor interfaces

• Peter Machon,
• Michael J. Wolf,
• Detlef Beckmann and
• Wolfgang Belzig

Beilstein J. Nanotechnol. 2022, 13, 682–688, doi:10.3762/bjnano.13.60

• states per volume is given as We now discuss the self-consistency relation for different values of the parameter ε’. Figure 2 shows the phase diagram for values ε’ = [100–0.1], which for a d = 10 nm aluminium layer roughly translates into fractions r = [1–0.001]. The plotted curves are the phase

• significant shift of the peak positions is visible for larger spin mixing angles. For sufficiently small ε’, spin mixing has little effect on Δ. Comparison of experiment and theory To illustrate our model, we use it to fit experimental data obtained on a sample made of a superconducting aluminium film on top

• a Si(111) substrate heated to 800 °C. In a second fabrication step, aluminium/aluminium oxide/copper tunnel junctions were fabricated on the EuS film using e-beam lithography and shadow evaporation. The nominal aluminium film thickness was d = 10 nm. The differential conductance g = dI/dV of the

Approaching microwave photon sensitivity with Al Josephson junctions

• Andrey L. Pankratov,
• Anna V. Gordeeva,
• Leonid S. Revin,
• Dmitry A. Ladeynov,
• Anton A. Yablokov and
• Leonid S. Kuzmin

Beilstein J. Nanotechnol. 2022, 13, 582–589, doi:10.3762/bjnano.13.50

• , Russia Lobachevsky State University of Nizhny Novgorod, 603950, Nizhny Novgorod, Russia Chalmers University of Technology, 41296, Gothenburg, Sweden 10.3762/bjnano.13.50 Abstract Here, we experimentally test the applicability of an aluminium Josephson junction of a few micrometers size as a single

• experiments of dark matter search [10][11][12] and the corresponding program initiated by INFN in Italy [13][14][15][16][17][18][19][20][21][22]. Our experiments show that typical aluminium Josephson junctions (JJs) can indeed have a few-photon sensitivity in the microwave frequency range, and a photon

Design and characterization of polymeric microneedles containing extracts of Brazilian green propolis

• Camila Felix Vecchi,
• Rafaela Said dos Santos,
• Jéssica Bassi da Silva and
• Marcos Luciano Bruschi

Beilstein J. Nanotechnol. 2022, 13, 503–516, doi:10.3762/bjnano.13.42

• to the vertical axis) to the polymeric MNs using a TA-XTplus texturometer (TA Instruments, Surrey, UK). The MN patches were connected to the mobile cylindrical probe (P/1 – 1″ diameter aluminium cylinder ) with double-sided tape. The probe was pressed against the defined surface (hard glass surface

Selected properties of Al_xZn_yO thin films prepared by reactive pulsed magnetron sputtering using a two-element Zn/Al target

• Witold Posadowski,
• Artur Wiatrowski,
• Jarosław Domaradzki and
• Michał Mazur

Beilstein J. Nanotechnol. 2022, 13, 344–354, doi:10.3762/bjnano.13.29

• : aluminium zinc oxide; magnetron sputtering; thin film; transparent conducting oxide; transparent electronics; Introduction Aluminium-doped zinc oxide (AZO) is a potential alternative to indium tin oxide (ITO) for transparent conducting oxide (TCO) electrodes in transparent electronic and photovoltaic

• , it can be considered that for films deposited at X ≥ 50 mm, more Al3+ ions were successfully incorporated into the host lattice as the aluminium content increases (confirmed by the EDS results) and the Al2ZnO4 phase decreases (confirmed by the XRD results). ZnO is a wide-bandgap semiconductor with

• less than 10% aluminium [26][27][28][29] taking into account Al, Zn, and O. In this work, the material composition was measured using EDS, in which the measurement of X-ray intensities of light elements, such as oxygen, can be difficult and often subject to systematic errors. Therefore, in the case of

Engineered titania nanomaterials in advanced clinical applications

• Padmavati Sahare,
• Paulina Govea Alvarez,
• Juan Manual Sanchez Yanez,
• Gabriel Luna-Bárcenas,
• Samik Chakraborty,
• Sujay Paul and
• Miriam Estevez

Beilstein J. Nanotechnol. 2022, 13, 201–218, doi:10.3762/bjnano.13.15

• . synthesized B-TiO2−x nps by a facile aluminium reduction process and modified its surface with PEG molecules (Figure 7) for high stability under physiological conditions. B-TiO2−x-PEG accumulates in tumor tissue via typical endocytosis processes and functions as nanosonosensitizer as well as photothermal

Sputtering onto liquids: a critical review

• Anastasiya Sergievskaya,
• Adrien Chauvin and
• Stephanos Konstantinidis

Beilstein J. Nanotechnol. 2022, 13, 10–53, doi:10.3762/bjnano.13.2

• research papers for almost 20 years until 1996 when two research groups reported SoL experiments. Ye et al. studied the formation of silver films on the surface of silicon oil [10] while Wagener et al. prepared silver and aluminium NPs by deposition onto silicon oil using various experimental conditions

Plasmon-enhanced photoluminescence from TiO₂ and TeO₂ thin films doped by Eu³⁺ for optoelectronic applications

• Marcin Łapiński,
• Jakub Czubek,
• Katarzyna Drozdowska,
• Anna Synak,
• Wojciech Sadowski and
• Barbara Kościelska

Beilstein J. Nanotechnol. 2021, 12, 1271–1278, doi:10.3762/bjnano.12.94

• platforms show an increased intensity of the excitation peak. Moreover, samples with an additional aluminium oxide ultrathin film exhibit a higher excitation intensity. The increased excitation for samples with Au nanostructures may be ascribed to the plasmonic resonance effect, which results in greater

Progress and innovation of nanostructured sulfur cathodes and metal-free anodes for room-temperature Na–S batteries

• Marina Tabuyo-Martínez,
• Bernd Wicklein and
• Pilar Aranda

Beilstein J. Nanotechnol. 2021, 12, 995–1020, doi:10.3762/bjnano.12.75

A Au/CuNiCoS₄/p-Si photodiode: electrical and morphological characterization

• Adem Koçyiğit,
• Adem Sarılmaz,
• Teoman Öztürk,
• Faruk Ozel and
• Murat Yıldırım

Beilstein J. Nanotechnol. 2021, 12, 984–994, doi:10.3762/bjnano.12.74

• /H2O (1:10) solution for eliminating the oxide layer and impurities from the surfaces. An ohmic contact with low resistance was made by evaporation of aluminium (Al, 99.999% from Kurt J. Lesker) with a thickness of 150 nm at 5 × 10−6 Torr on the back side of the p-type Si substrate and subsequent

Uniform arrays of gold nanoelectrodes with tuneable recess depth

• Elena O. Gordeeva,
• Ilya V. Roslyakov,
• Alexey P. Leontiev,
• Alexey A. Klimenko and
• Kirill S. Napolskii

Beilstein J. Nanotechnol. 2021, 12, 957–964, doi:10.3762/bjnano.12.72

• alternative approach includes bulk electrode structuring by deposition or etching techniques using self-assembled arrays of colloidal nanoparticles [15], liquid crystals [16], or track-etched membranes [17][18][19] as template or mask, respectively. Among porous templates, anodic aluminium oxide (AAO) allows

9.1% efficient zinc oxide/silicon solar cells on a 50 μm thick Si absorber

• Rafal Pietruszka,
• Bartlomiej S. Witkowski,
• Monika Ozga,
• Katarzyna Gwozdz,
• Ewa Placzek-Popko and
• Marek Godlewski

Beilstein J. Nanotechnol. 2021, 12, 766–774, doi:10.3762/bjnano.12.60

• research groups. This technology was invented in the 1970s by Tuomo Suntola from Finland [4]. Thanks to the unique properties of this technology, materials produced by ALD quickly found a number of applications in PV. For example, ultrathin films of aluminium oxide (Al2O3) are used to passivate silicon

• during manufacture [5]. Moreover, thin films of zinc oxide, aluminium-doped zinc oxide (AZO), and/or gallium-doped ZnO (GZO) have been successfully used in organic [6], perovskite [7], and CIGS [8] solar cells. Thanks to excellent electrical and optical parameters of AZO and GZO, these films are

• inexpensive alternatives for indium tin oxide (ITO) [9]. In this work, we used ALD to deposit zinc oxide nanoseeds, magnesium-doped zinc oxide (MZO) layers and aluminium-doped zinc oxide films. We thus continue our interest on photovoltaic structures based on thin films of ZnO. Recently, there have been

Gold(I) N-heterocyclic carbene precursors for focused electron beam-induced deposition

• Cristiano Glessi,
• Aya Mahgoub,
• Cornelis W. Hagen and
• Mats Tilset

Beilstein J. Nanotechnol. 2021, 12, 257–269, doi:10.3762/bjnano.12.21

• mounted on a custom-built heater [38] shown in Figure 2 and crystals of the precursor were placed directly on the substrate. The low volatility of the compounds required heating above the maximum allowable temperature of a standard GIS to effectively sublime the material. An aluminium plate covered the

• from the bottom of an aluminium plate (9.5 × 9.5 × 1 mm3). The plate lies directly on the 10 × 10 mm2 silicon substrate, covering some precursor crystals positioned on the substrate, and is kept in place with vacuum-compatible Kapton tape. Only small quantities are needed to test a precursor, and a

ZnO and MXenes as electrode materials for supercapacitor devices

• Ameen Uddin Ammar,
• Ipek Deniz Yildirim,
• Feray Bakan and
• Emre Erdem

Beilstein J. Nanotechnol. 2021, 12, 49–57, doi:10.3762/bjnano.12.4

• biocompatibility, photothermal efficiency, low Seebeck coefficient, as well as good conductivity. They synthesized tantalum carbide MXene sheets from a tantalum aluminum carbide (Ta4AlC3) MAX phase through etching the intermediate aluminium with the aid of hydrofluoric acid (HF). Analysis of the synthesized

Atomic layer deposited films of Al₂O₃ on fluorine-doped tin oxide electrodes: stability and barrier properties

• Hana Krýsová,
• Michael Neumann-Spallart,
• Hana Tarábková,
• Pavel Janda,
• Ladislav Kavan and
• Josef Krýsa

Beilstein J. Nanotechnol. 2021, 12, 24–34, doi:10.3762/bjnano.12.2

• semiconducting electrodes, such as ZnO. Aluminium oxide is another promising candidate for this task. It is amphoteric but insoluble in aqueous media at a neutral pH value [8][9]. ALD oxide layers, including Al2O3, were used as barrier coatings on copper to protect against corrosion in 0.1 M NaCl [10]. As

• identical deposition cycles. Trimethylaluminium (TMA) and water (both from Strem Chemicals, Inc.) were used as precursors. The temperature range for all the organometallic aluminium precursors was 30–300 °C [17]. The deposition of Al2O3 was performed at 300 °C, as recommended [4]. The pulse of the TMA

• precursor was 0.1 s with a purge time of 5 s and the pulse of H2O was 0.1 s with a purge time of 10 s. TMA and water were maintained at 22 °C. Nitrogen (99.999%, Linde) was used as a carrier gas. The deposition of aluminium oxide films on silicon or FTO was carried out by performing 30, 60, 120, and 200

Plant growth regulation by seed coating with films of alginate and auxin-intercalated layered double hydroxides

• Vander A. de Castro,
• Valber G. O. Duarte,
• Danúbia A. C. Nobre,
• Geraldo H. Silva,
• Vera R. L. Constantino,
• Frederico G. Pinto,
• Willian R. Macedo and
• Jairo Tronto

Beilstein J. Nanotechnol. 2020, 11, 1082–1091, doi:10.3762/bjnano.11.93

• growth. This work describes (i) the synthesis and characterization of a zinc–aluminium LDH intercalated with NAA (ZnAl-NAA-LDH); (ii) the preparation a hybrid films for bean seed coating (Phaseolus vulgaris L.) containing a mixture of sodium alginate and ZnAl-NAA-LDH; (iii) bioassays with the coated

• °C (mass loss of 9.6%) and the release of a fragment with m/z 18 suggests sample dehydration. The second step from 155 °C up to about 260 °C (mass loss of 9.1% and m/z 18) is assigned to the dehydroxylation of the zinc–aluminium LDH layers [27]. Between 260 and 500 °C, the sample loses about 38% of

Microwave photon detection by an Al Josephson junction

• Leonid S. Revin,
• Andrey L. Pankratov,
• Anna V. Gordeeva,
• Anton A. Yablokov,
• Igor V. Rakut,
• Victor O. Zbrozhek and
• Leonid S. Kuzmin

Beilstein J. Nanotechnol. 2020, 11, 960–965, doi:10.3762/bjnano.11.80

• Novgorod, Russia Lobachevsky State University of Nizhny Novgorod, Nizhny Novgorod, Russia Chalmers University of Technology, SE-41296 Gothenburg, Sweden 10.3762/bjnano.11.80 Abstract An aluminium Josephson junction (JJ), with a critical current suppressed by a factor of three compared with the maximal

• through the JJ is observed, which resembles the differentiation between N and N + 1 photon absorption. Keywords: aluminium; Josephson junction; microwaves; phase diffusion; photon counter; switching current distribution; Introduction Currently, an important problem is the creation of single-photon

• -photon counter described in [4]. We study the possibility of detecting photons in the gigahertz frequency range using an aluminium Josephson junction with a suppressed critical current. The main requirement to this counter is an extremely large lifetime (thousands of seconds), orders of magnitude larger

A set of empirical equations describing the observed colours of metal–anodic aluminium oxide–Al nanostructures

• Cristina V. Manzano,
• Jakob J. Schwiedrzik,
• Gerhard Bürki,
• Laszlo Pethö,
• Johann Michler and
• Laetitia Philippe

Beilstein J. Nanotechnol. 2020, 11, 798–806, doi:10.3762/bjnano.11.64

• .11.64 Abstract Structural colours have received a lot of attention regarding the reproduction of the vivid colours found in nature. In this study, metal–anodic aluminium oxide (AAO)–Al nanostructures were deposited using a two-step anodization and sputtering process to produce self-ordered anodic

• aluminium oxide films and a metal layer (8 nm Cr and 25, 17.5 and 10 nm of Au), respectively. AAO films of different thickness were anodized and the Yxy values (Y is the luminance value, and x and y are the chromaticity values) were obtained via reflectance measurements. An empirical model based on the

• thickness and porosity of the nanostructures was determined, which describes a gamut of colours. The proposed mathematical model can be applied in different fields, such as wavelength absorbers, RGB (red, green, blue) display devices, as well as chemical or optical sensors. Keywords: anodic aluminium oxide

Structural optical and electrical properties of a transparent conductive ITO/Al–Ag/ITO multilayer contact

• Aliyu Kabiru Isiyaku,
• Ahmad Hadi Ali and
• Nafarizal Nayan

Beilstein J. Nanotechnol. 2020, 11, 695–702, doi:10.3762/bjnano.11.57

• for transparent conductive oxide (TCO) films due to its good optical and electrical properties. Improving the optoelectronic properties of ITO films with reduced thickness is crucial and quite challenging. ITO-based multilayer films with an aluminium–silver (Al–Ag) interlayer (ITO/Al–Ag/ITO) and a

• deposition of ITO films. Aluminium (Al) and silver (Ag) targets of 99.999% purity were purchased and used for the deposition of the Al–Ag interlayer between top and bottom ITO layers. Silicon wafers [Si(100), n-type, phosphorous, 1–10 Ω·cm and 525 ± 25 μm] or commercial soda-lime glass (for optical

Preparation, characterization and photocatalytic performance of heterostructured CuO–ZnO-loaded composite nanofiber membranes

• Wei Fang,
• Liang Yu and
• Lan Xu

Beilstein J. Nanotechnol. 2020, 11, 631–650, doi:10.3762/bjnano.11.50

• needle tip to collector were, respectively, maintained at 20 kV and 18 cm. The electrospinning experiments were carried out at room temperature (25 ± 2 °C) and a relative humidity of (55 ± 5%), and the electrospun Cu(Ac)2/Zn(Ac)2/PVDF/PAN CNFMs were collected and carefully peeled off from the aluminium

Identification of physicochemical properties that modulate nanoparticle aggregation in blood

• Ludovica Soddu,
• Duong N. Trinh,
• Eimear Dunne,
• Dermot Kenny,
• Giorgia Bernardini,
• Ida Kokalari,
• Arianna Marucco,
• Marco P. Monopoli and
• Ivana Fenoglio

Beilstein J. Nanotechnol. 2020, 11, 550–567, doi:10.3762/bjnano.11.44

• microscopy (SEM), using a Zeiss Evo 50XVP (Assing) instrument. CNPs and SNPs suspensions were diluted up to 0.05 mg/mL in ultrapure water. A volume of 20 μL of the diluted suspensions was mounted on aluminium stubs using double-sided adhesive carbon tape and silicon wafers. The samples were dried overnight

Poly(1-vinylimidazole) polyplexes as novel therapeutic gene carriers for lung cancer therapy

• Gayathri Kandasamy,
• Elena N. Danilovtseva,
• Vadim V. Annenkov and
• Uma Maheswari Krishnan

Beilstein J. Nanotechnol. 2020, 11, 354–369, doi:10.3762/bjnano.11.26

• nanoparticles and of the PVI–siRNA polyplex were recorded using differential scanning calorimetry (DSC, Polyma 214, Netzsch, Germany) in the temperature range of 0–300 °C in a nitrogen atmosphere at a scan rate of 5 °C·min−1. The samples were placed in an aluminium pan with lid, which also served as the

Rational design of block copolymer self-assemblies in photodynamic therapy

• Maxime Demazeau,
• Laure Gibot,
• Anne-Françoise Mingotaud,
• Patricia Vicendo,
• Clément Roux and
• Barbara Lonetti

Beilstein J. Nanotechnol. 2020, 11, 180–212, doi:10.3762/bjnano.11.15

• PEO-PAsp micelles [146]. A typical recent example describes the introduction of benzylglycidyl ether groups on the hydrophobic backbone of polylactide, in order to improve the loading of aluminium phthalocyanine AlClPc [45]. Using a peptide backbone is another elegant and powerful means to optimize

Self-assembly of a terbium(III) 1D coordination polymer on mica

• Quentin Evrard,
• Giuseppe Cucinotta,
• Felix Houard,
• Guillaume Calvez,
• Yan Suffren,
• Carole Daiguebonne,
• Olivier Guillou,
• Andrea Caneschi,
• Matteo Mannini and
• Kevin Bernot

Beilstein J. Nanotechnol. 2019, 10, 2440–2448, doi:10.3762/bjnano.10.234

• tetrahedrons with iron oxides or by the substitution of the aluminium ions in the octahedral positions of the mica 2D network [26]. Consequently, the free substrate may have a significant magnetic response that could be of the same order of magnitude as that of the deposited material. This is the reason why

• on the mica surface that can lead to the formation of potassium carbonate (K2CO3) when mica is air-cleaved. Recent findings [32][33][34][35] show that the mechanism of K+ depletion from air-cleaved mica is not fully known but resembles the one observed on aluminium oxide [36], iron oxide [37] or

Targeted therapeutic effect against the breast cancer cell line MCF-7 with a CuFe₂O₄/silica/cisplatin nanocomposite formulation

• B. Rabindran Jermy,
• Vijaya Ravinayagam,
• Widyan A. Alamoudi,
• Dana Almohazey,
• Hatim Dafalla,
• Lina Hussain Allehaibi,
• Abdulhadi Baykal,
• Muhammet S. Toprak and
• Thirunavukkarasu Somanathan

Beilstein J. Nanotechnol. 2019, 10, 2217–2228, doi:10.3762/bjnano.10.214

• and Methods HYPS was purchased from Superior Silica, USA. Cu(NO3)2·3H2O, Fe(NO3)3·9H2O, cisplatin and aluminium mesocellular foam with a high surface area of 539 m2/g and large aperture pore size of 14.7 nm was obtained from Sigma-Aldrich. Silicalite with a surface area of 313 m2/g was prepared in

Ultrathin Ni_1−xCo_xS₂ nanoflakes as high energy density electrode materials for asymmetric supercapacitors

• Xiaoxiang Wang,
• Teng Wang,
• Rusen Zhou,
• Lijuan Fan,
• Shengli Zhang,
• Feng Yu,
• Tuquabo Tesfamichael,
• Liwei Su and
• Hongxia Wang

Beilstein J. Nanotechnol. 2019, 10, 2207–2216, doi:10.3762/bjnano.10.213

• supported by aluminium SEM sample stages. Chemical composition and valence states of each element in the material are further confirmed by using XPS. The high-resolution XPS spectra confirm the existence of nickel, cobalt, and sulfur. After fitting the XPS with the Gaussian method, the HRXPS spectrum of Ni