The effect of metal surface nanomorphology on the output performance of a TENG

• Yiru Wang,
• Xin Zhao,
• Yang Liu and
• Wenjun Zhou

Beilstein J. Nanotechnol. 2022, 13, 298–312, doi:10.3762/bjnano.13.25

• Normal University, Neijiang 641100, China 10.3762/bjnano.13.25 Abstract In this work, the effect of charge density and nanomorphology of a metal tip on the output performance of a triboelectric nanogenerator (TENG) is studied. The basic working principle of the TENG is charge transfer after separation

• surface. When the materials are separated, the positive and negative electrostatic charges on the materials will also be separated, resulting in a potential difference. The charge transfer strongly depends on the work functions of the two materials in contact, for example, metal–metal, semiconductor

Coordination-assembled myricetin nanoarchitectonics for sustainably scavenging free radicals

• Xiaoyan Ma,
• Haoning Gong,
• Kenji Ogino,
• Xuehai Yan and
• Ruirui Xing

Beilstein J. Nanotechnol. 2022, 13, 284–291, doi:10.3762/bjnano.13.23

• 5.5), and MZG nanoparticles (pH 5.5) were measured. The UV–vis absorption spectrum of MZG nanoparticles exhibited a blue shift at 550 nm, compared with Myr/Zn2+, which was assigned to the charge transfer between GSH and Zn2+ (Figure 2c). These results demonstrated that Zn2+ as the coordination

Impact of device design on the electronic and optoelectronic properties of integrated Ru-terpyridine complexes

• Max Mennicken,
• Sophia Katharina Peter,
• Corinna Kaulen,
• Ulrich Simon and
• Silvia Karthäuser

Beilstein J. Nanotechnol. 2022, 13, 219–229, doi:10.3762/bjnano.13.16

• -ligand charge transfer absorption bands and a relatively long lifetime of the triplet state as well as voltage-driven molecular switching in solid-state molecular junctions [11][12][13][14][15]. In addition, Ru(TP)2-complexes and the corresponding supramolecular wires exhibit a rod-like structure, which

• nm, while the metal-to-ligand charge transfer band of Ru(MPTP)2-complexes is located at 499 nm. However, a considerable overlap of both bands is given (Supporting Information File 1, Figure S13) and, thus, a subsequent transfer of the incident electromagnetic energy to the Ru(MPTP)2-complexes bound

• -complex, that is, a metal-to-ligand charge transfer is induced. The Ru2+ cation creates an exciton consisting of a threefold positive Ru3+ and a negative charge located on the MPTP ligand. Subsequently, these charge carriers are separated in the applied electrical field. Therefore, the electrical field

Tin dioxide nanomaterial-based photocatalysts for nitrogen oxide oxidation: a review

• Viet Van Pham,
• Hong-Huy Tran,
• Thao Kim Truong and
• Thi Minh Cao

Beilstein J. Nanotechnol. 2022, 13, 96–113, doi:10.3762/bjnano.13.7

• process. Table 1 shows a comparison of the NO photocatalytic oxidation ability of neat SnO2 and modified SnO2 materials. Recent studies on this material system mainly focus on modifying SnO2 toward the application in the visible light region. Charge transfer improvement The combination of SnO2 with other

• co-photocatalysts, including inorganic and organic semiconductors, is a practical approach to enhance the charge transfer efficacy for the photocatalytic process. The photocatalytic degradation of NOx over SnO2 as a host photocatalyst is reported to be considerably enhanced after the combination with

• transition of photogenerated carriers used for the NO removal [37]. Pham et al. showcased a step-scheme (S-scheme) photocatalyst composed of 2D/0D g-C3N4 nanosheet-assisted SnO2 NPs (g-C3N4/SnO2) for removing NO with low NO2 generation. This work established an S-scheme charge transfer path by combining

The effect of cobalt on morphology, structure, and ORR activity of electrospun carbon fibre mats in aqueous alkaline environments

• Markus Gehring,
• Tobias Kutsch,
• Osmane Camara,
• Alexandre Merlen,
• Hermann Tempel,
• Hans Kungl and
• Rüdiger-A. Eichel

Beilstein J. Nanotechnol. 2021, 12, 1173–1186, doi:10.3762/bjnano.12.87

• . The overpotential at a given current density is a measure of the power losses in the system resulting from internal resistances, such as charge transfer resistance and Ohmic resistance relevant to the practical capacity of the system. The resulting values determined in this fashion are summarised in

Irradiation-driven molecular dynamics simulation of the FEBID process for Pt(PF₃)₄

• Alexey Prosvetov,
• Alexey V. Verkhovtsev,
• Gennady Sushko and
• Andrey V. Solov’yov

Beilstein J. Nanotechnol. 2021, 12, 1151–1172, doi:10.3762/bjnano.12.86

• for quantum and chemical transformation of surface-adsorbed molecular systems under focused electron beam irradiation [13][14][15][16]. Within the IDMD framework various quantum processes occurring in an irradiated system (e.g., ionization, bond dissociation via electron attachment, or charge transfer

Molecular assemblies on surfaces: towards physical and electronic decoupling of organic molecules

• Sabine Maier and
• Meike Stöhr

Beilstein J. Nanotechnol. 2021, 12, 950–956, doi:10.3762/bjnano.12.71

• substrate. Hurdax et al. reported that both charged and neutral species of sexiphenyl can co-exist on thin dielectric MgO films on Ag(100) [89]. Due to the changed work function of the substrate, charging of the adsorbates is enabled by electron tunneling. The charge transfer strongly influences the

Modification of a SERS-active Ag surface to promote adsorption of charged analytes: effect of Cu²⁺ ions

• Bahdan V. Ranishenka,
• Andrei Yu. Panarin,
• Irina A. Chelnokova,
• Sergei N. Terekhov,
• Peter Mojzes and
• Vadim V. Shmanai

Beilstein J. Nanotechnol. 2021, 12, 902–912, doi:10.3762/bjnano.12.67

• basic mechanism is EM through localized surface plasmon resonances (LSPRs) on the metal surface [16]. CE is at least two orders of magnitude weaker than EM. The CE mechanism is supposed to be caused by a charge transfer between the plasmonic surface and the chemically adsorbed analyte molecules, which

Nanoporous and nonporous conjugated donor–acceptor polymer semiconductors for photocatalytic hydrogen production

• Zhao-Qi Sheng,
• Yu-Qin Xing,
• Yan Chen,
• Guang Zhang,
• Shi-Yong Liu and
• Long Chen

Beilstein J. Nanotechnol. 2021, 12, 607–623, doi:10.3762/bjnano.12.50

• tunable bandgaps, high charge carrier mobility, and efficient intramolecular charge transfer. In this minireview, recent advances of D–A polymers in photocatalytic hydrogen evolution are summarized with a particular focus on modulating the optical and electronic properties of CPs by varying the acceptor

• of CTFs. The carbazole–triazine-containing CTF P1 (Figure 2) triggered a strong intramolecular charge transfer (ICT) and achieved a high HER of 538 μmol·h−1 (50 mg). Bojdys and co-workers reported a series of CTFs with diverse functional moieties (e.g., heterocycles containing S and/or N) at the

• . However, HER is affected by the interplay of several factors, including surface area, light absorption range, crystallinity, charge transfer, and separation. Two azine-linked COFs with three pyridine segments neighboring the central benzene or triazine fragment were prepared to make comparisons, that is

Local stiffness and work function variations of hexagonal boron nitride on Cu(111)

• Abhishek Grewal,
• Yuqi Wang,
• Matthias Münks,
• Klaus Kern and
• Markus Ternes

Beilstein J. Nanotechnol. 2021, 12, 559–565, doi:10.3762/bjnano.12.46

• originate from a locally varying charge transfer between the substrate and the dielectric layer [38][39][40]. In our studied substrate, it is the lattice mismatch between h-BN and the Cu(111) substrate that leads to a varying atomic registry and subsequently induces a lateral modulation of the charge

• transfer [41]. Additionally, this leads to in-plane electric fields, which have been shown to trap atoms, molecules, and nanoclusters [11][13][42]. To map the local Φ fluctuations and to correlate them with the structural properties of the surface, we use two complementary methods: The first method is

Simulation of gas sensing with a triboelectric nanogenerator

• Kaiqin Zhao,
• Hua Gan,
• Huan Li,
• Ziyu Liu and
• Zhiyuan Zhu

Beilstein J. Nanotechnol. 2021, 12, 507–516, doi:10.3762/bjnano.12.41

• ], single electrode mode [32][33][34], and independent layer mode [35]. In order to explain the charge transfer process between two friction materials in contact, various models have been proposed and explored, such as electron cloud model [36][37][38], ion transfer model [39], and material transfer model

Interface interaction of transition metal phthalocyanines with strontium titanate (100)

• Reimer Karstens,
• Thomas Chassé and
• Heiko Peisert

Beilstein J. Nanotechnol. 2021, 12, 485–496, doi:10.3762/bjnano.12.39

• first monolayer on the oxide surface depends on the central metal atom of the phthalocyanine, whereas the substrate preparation has minor influence on the interaction between CoPc and SrTiO3(100). Differences of the interaction mechanism to related TiO2 surfaces are discussed. Keywords: charge transfer

• properties. Hence, TMPcs are well suited for systematic studies of interface properties. The fluorination of TMPcs varies exceptionally the ionization potential (IP), affecting distinctly the interface properties [29][30][31][32]. As recently shown for FePcFx/MoS2 [33], a charge transfer at interfaces might

• structural ordering of the near-surface region below the topmost layer, and we may rule out a completely SrO-terminated surface. CoPcFx on STO(100) Possible interactions between organic molecules and different substrates may include charge transfer processes or even chemical reactions. In the case of

Boosting of photocatalytic hydrogen evolution via chlorine doping of polymeric carbon nitride

• Malgorzata Aleksandrzak,
• Michalina Kijaczko,
• Wojciech Kukulka,
• Daria Baranowska,
• Martyna Baca,
• Beata Zielinska and
• Ewa Mijowska

Beilstein J. Nanotechnol. 2021, 12, 473–484, doi:10.3762/bjnano.12.38

• the EIS spectrum is related to the charge-transfer resistance at the electrode–electrolyte interface [71]. The EIS arc radius of Cl-PCN is smaller than that of PCN. Its impedance is reduced compared to PCN, indicating that Cl doping decreased the charge-transfer resistance of polymeric carbon nitride

• surface reaction sites before recombination leading to hydrogen evolution. These results are consistent with PL spectroscopy and EIS results, revealing a better separation and charge transfer, respectively, after chlorine doping. Moreover, it was revealed that chlorine doping affected the CB shift to a

Solution combustion synthesis of a nanometer-scale Co₃O₄ anode material for Li-ion batteries

• Monika Michalska,
• Huajun Xu,
• Qingmin Shan,
• Shiqiang Zhang,
• Yohan Dall'Agnese,
• Yu Gao,
• Amrita Jain and
• Marcin Krajewski

Beilstein J. Nanotechnol. 2021, 12, 424–431, doi:10.3762/bjnano.12.34

• Information File 1. These EIS features represent the charge transfer at the electrode–electrolyte interface (Rct) and the Warburg impedance (W), which is attributed to the diffusion of Li+ ions in the bulk electrode material [25][38]. The plots for the cycled cell are slightly different. They are composed of

• represent the charge transfer at the electrode–electrolyte interface (Rct) and the Warburg impedance (W), respectively. The semicircle at high frequencies is mainly attributed to SEI resistance (RSEI) and contact resistance (Rf) [13][15][20][21][25][38]. At this point, it should be also mentioned that the

• decreased for the cycled cell. This indicates that the charge transfer reaction has been improved due to cycling. Also, a slight cycle-to-cycle increase of Rct as well as of RSEI is observed for the cycled sample. This phenomenon might be explained by the growth of the SEI layer, which provides some

Nickel nanoparticle-decorated reduced graphene oxide/WO₃ nanocomposite – a promising candidate for gas sensing

• Ilka Simon,
• Alexandr Savitsky,
• Rolf Mülhaupt,
• Vladimir Pankov and
• Christoph Janiak

Beilstein J. Nanotechnol. 2021, 12, 343–353, doi:10.3762/bjnano.12.28

• graphene and metal oxide. In the case of reduced graphene oxide (semiconductor), various reasons are considered, such as the appearance of p–n junctions that shift the Fermi level of the oxide. There is evidence of effective charge transfer between graphene and nanospheres through chemical bonds. Emergence

• plays an important role in charge transfer processes and leads to the enhancement in the gas sensing performance due to the synergistic effect between rGO (p-type) WO3 (n-type) [29]. In [37][53], the formation of C–O–W bonds at the interphase boundaries was observed, when studying a rGO/WO3 composite

• using XPS and Raman spectroscopy. Such bonds can play an important role also in our case with regard to charge transfer. It has been established that adsorption of NO2 molecules will cause upward band bending by capturing free electrons from the conduction band and shift the Fermi level of WO3 away from

Extended iron phthalocyanine islands self-assembled on a Ge(001):H surface

• Rafal Zuzak,
• Marek Szymonski and
• Szymon Godlewski

Beilstein J. Nanotechnol. 2021, 12, 232–241, doi:10.3762/bjnano.12.19

• scanning probe microscopes [1][2][3]. At the same time, however, metallic substrates usually influence the properties of adsorbed molecular species, leading to hybridization, charge transfer, or screening at the interface [4][5][6]. Also, metallic surfaces may provide relatively weak binding, dominated by

Paper-based triboelectric nanogenerators and their applications: a review

• Jing Han,
• Nuo Xu,
• Yuchen Liang,
• Mei Ding,
• Junyi Zhai,
• Qijun Sun and
• Zhong Lin Wang

Beilstein J. Nanotechnol. 2021, 12, 151–171, doi:10.3762/bjnano.12.12

• several typical examples in which P-TENGs are used. This paper starts with an overview of TENGs and the corresponding working mechanism of four basic working modes based on charge transfer and on the electron-cloud potential-well model. Regarding surface modification and fabrication methods involving

• and highly efficient energy-harvesting systems. To conclude the review, perspectives and proposals regarding future potential applications and research directions are discussed. Review Four working modes of TENGs and charge-transfer mechanisms TENGs, which are emerging and efficient apparatus for

• (most common design in previous works) as a typical representative example, we further systematically analyze the working mechanism of the detailed charge-transfer process. Figure 2b elucidates the charge generation and the electron-transfer process at the friction interfaces (paper/the other dielectric

ZnO and MXenes as electrode materials for supercapacitor devices

• Ameen Uddin Ammar,
• Ipek Deniz Yildirim,
• Feray Bakan and
• Emre Erdem

Beilstein J. Nanotechnol. 2021, 12, 49–57, doi:10.3762/bjnano.12.4

• . Therefore, different electrical components contribute to the equivalent circuit of the EIS results. Warburg element, charge transfer resistance (Rct), and equivalent series resistance (ESR) are some of the elements that contribute to the resistive behavior [11]. At this point, we highly suggest to the

Atomic layer deposited films of Al₂O₃ on fluorine-doped tin oxide electrodes: stability and barrier properties

• Hana Krýsová,
• Michael Neumann-Spallart,
• Hana Tarábková,
• Pavel Janda,
• Ladislav Kavan and
• Josef Krýsa

Beilstein J. Nanotechnol. 2021, 12, 24–34, doi:10.3762/bjnano.12.2

• that of pure FTO is higher than three. This means that there are B-type defects in the barrier film. These defects cause not only the delamination of the Al2O3 film from the FTO substrate, but also a slowdown of the charge-transfer kinetics (accompanied by a strong increase in ΔEpp). The Table 1 shows

• voltammogram of the sample resembled that of pure FTO, indicating that a significant charge transfer occurred at the electrolyte solution/FTO interface. The blocking properties of a 17 nm thick Al2O3 film after a 5 min exposure to 1 M NaOH were evaluated via EPA calculation and shown in Table 1. A 5 min

Free and partially encapsulated manganese ferrite nanoparticles in multiwall carbon nanotubes

• Saja Al-Khabouri,
• Salim Al-Harthi,
• Toru Maekawa,
• Mohamed E. Elzain,
• Ashraf Al-Hinai,
• Ahmed D. Al-Rawas,
• Abbsher M. Gismelseed,
• Ali A. Yousif and
• Myo Tay Zar Myint

Beilstein J. Nanotechnol. 2020, 11, 1891–1904, doi:10.3762/bjnano.11.170

• manganese ferrite nanoparticles inside the tubes is observed as a shift in the X-ray diffraction peaks and as an increase in stress, hyperfine field, and coercivity when compared to free manganese ferrite nanoparticles. On the other hand, a strong charge transfer from the multiwall carbon nanotubes is

• ferrite nanoparticles in comparison to free manganese ferrite nanoparticles, which leads to an enhancement of the metallic properties. Keywords: carbon nanotubes; charge transfer; manganese ferrite; metallic nanoparticles; partial encapsulation; stress; surface; Introduction Since the discovery of

• the change in intensity of the emitted electrons from the π band to a strong charge transfer between MWCNTs and the functionalized materials [37]. In our case, the π band signal in MnFe2O4/MWCNTs is obscured by the presence of the Mn 3d signal, which makes it difficult to draw any conclusion related

Unravelling the interfacial interaction in mesoporous SiO₂@nickel phyllosilicate/TiO₂ core–shell nanostructures for photocatalytic activity

• Bridget K. Mutuma,
• Xiluva Mathebula,
• Isaac Nongwe,
• Bonakele P. Mtolo,
• Boitumelo J. Matsoso,
• Rudolph Erasmus,
• Zikhona Tetana and
• Neil J. Coville

Beilstein J. Nanotechnol. 2020, 11, 1834–1846, doi:10.3762/bjnano.11.165

• metal oxides, such as ZrO2 [16] and SiO2 [17], influence the morphology and surface features of the resulting binary metal oxide semiconductors. Moreover, these binary metal oxide semiconductors act as charge-transfer catalysts and significantly reduce the electron–hole recombination [18][19]. Another

• that facilitates easy adsorption of organic molecules and their transfer onto the active sites of TiO2 [22][23]. Additionally, the interaction between SiO2 and TiO2 could result in the creation of oxygen vacancies that promote charge-transfer processes and, hence, enhance the photocatalytic activity

• the bandgap energy value of TiO2 (3.2 eV) to approx. 2.7 eV for Ni2+-doped TiO2 was reported by Devi and co-workers [51]. They associated the shift in light absorption to the charge transfer between the interacting ions. Although there are only a few studies on nickel phyllosilicates, a prior

Self-standing heterostructured NiC_x-NiFe-NC/biochar as a highly efficient cathode for lithium–oxygen batteries

• Shengyu Jing,
• Xu Gong,
• Shan Ji,
• Linhui Jia,
• Bruno G. Pollet,
• Sheng Yan and
• Huagen Liang

Beilstein J. Nanotechnol. 2020, 11, 1809–1821, doi:10.3762/bjnano.11.163

• seems to facilitate the process of adsorption/desorption of intermediate species and the charge transfer ability during hydrogen evolution reaction (HER)/OER. In addition, the interfaces between Ni3C and N-doped C probably strongly reshuffle the electronic density, resulting in enhanced catalytic

• . The ohmic resistance (RΩ) and charge-transfer resistance (Rct) values of the fresh sample and of the sample after the first charge and first discharge were obtained by analyzing the EIS curves (Table 2). The value of RΩ of NiFe-PBA/PP-T after the first discharge was higher than that of the fresh

Molecular dynamics modeling of the influence forming process parameters on the structure and morphology of a superconducting spin valve

• Alexander Vakhrushev,
• Aleksey Fedotov,
• Vladimir Boian,
• Roman Morari and
• Anatolie Sidorenko

Beilstein J. Nanotechnol. 2020, 11, 1776–1788, doi:10.3762/bjnano.11.160

• nanostructures are a new type of quantum electronics elements based on electron spin transport. Unlike conventional electronics, spintronics uses not only charge transfer, but also the electron spin in solids, solving the problem of transport and recording of information [1][2][3][4][5][6][7]. Based on the basic

The influence of an interfacial hBN layer on the fluorescence of an organic molecule

• Christine Brülke,
• Oliver Bauer and
• Moritz M. Sokolowski

Beilstein J. Nanotechnol. 2020, 11, 1663–1684, doi:10.3762/bjnano.11.149

• a 2DM layer grown on a metal characterizes the degree of electronic coupling of the molecular and metallic states. For completeness, we note that quenching of an electronic excitation of a molecule in the first layers on a metal surface can be the result of interfacial charge transfer (CT) [5] or of

• LUMO of PTCDA was found on Ag(111), but not on Au(111) [33]. Thus, the quenching on Ag(111) is directly understood by the static charge transfer seen in UPS. The quenching on Au(111), not as evident from UPS, demonstrates the sensitivity of FL spectroscopy to an overlap of wave functions of excited

PTCDA adsorption on CaF₂ thin films

• Philipp Rahe

Beilstein J. Nanotechnol. 2020, 11, 1615–1622, doi:10.3762/bjnano.11.144

• , coupling to defects within the CaF1 layer, or charge transfer into the LUMO. Imaging at a positive sample bias of +1.5 V was performed in constant-height mode as the reduced sample conductivity at positive bias impeded operation in constant-current mode. Still, conductivity through PTCDA molecules is also