A biomimetic approach towards a universal slippery liquid infused surface coating

• Ryan A. Faase,
• Madeleine H. Hummel,
• AnneMarie V. Hasbrook,
• Andrew P. Carpenter and
• Joe E. Baio

Beilstein J. Nanotechnol. 2024, 15, 1376–1389, doi:10.3762/bjnano.15.111

• is anchored to a substrate, creating a smooth liquid layer that is energetically favored to interact with the solid surface. The surface chemistry of the anchoring layer is crucial to the viability of the overall coating as the lubricant must have a greater affinity for the substrate surface than for

Elastic modulus of β-Ga₂O₃ nanowires measured by resonance and three-point bending techniques

• Annamarija Trausa,
• Sven Oras,
• Sergei Vlassov,
• Mikk Antsov,
• Tauno Tiirats,
• Andreas Kyritsakis,
• Boris Polyakov and
• Edgars Butanovs

Beilstein J. Nanotechnol. 2024, 15, 704–712, doi:10.3762/bjnano.15.58

• , and resonance frequencies were compared before and after the “welding” process (Table S2 in Supporting Information File 1). No significant difference was observed, indicating that the NWs were strongly fixed on the Si substrate and did not require any additional anchoring. The elastic modulus is then

Functional fibrillar interfaces: Biological hair as inspiration across scales

• Guillermo J. Amador,
• Brett Klaassen van Oorschot,
• Caiying Liao,
• Jianing Wu and
• Da Wei

Beilstein J. Nanotechnol. 2024, 15, 664–677, doi:10.3762/bjnano.15.55

• performance. Examples are reversible adhesion in geckos (Figure 3A), anchoring in burrowing earthworms (Figure 3B), flying in bristled-wing insects, such as thrips, (Figure 3C), and swimming in unicellular microorganisms, such as microalgae (Figure 3D). Climbing Adhesive hairs have been observed on the foot

• [21][22]. Burrowing The use of hairs to generate frictional forces is not unique to animals that climb. Hair-like setae on the skin of earthworms aid in burrowing by increasing friction and providing anisotropic anchoring [65][66][67]. When burrowing, the earthworm mainly uses cavity expansion to

• worm to anchor tighter to the surrounding soil. Meanwhile, when the circular muscles relax, the setae deflect and interact less with the soil. This anisotropic anchoring has been realized in a bio-inspired burrowing soft robot [70]. Flying Flying organisms span about eight orders of magnitude in mass

Study of the reusability and stability of nylon nanofibres as an antibody immobilisation surface

• Inés Peraile,
• Matilde Gil-García,
• Laura González-López,
• Nushin A. Dabbagh-Escalante,
• Juan C. Cabria-Ramos and
• Paloma Lorenzo-Lozano

Beilstein J. Nanotechnol. 2024, 15, 83–94, doi:10.3762/bjnano.15.8

• , because the NFs protects the immunocapture system better than a planar surface specialised for anchoring antibodies, they allow the immunocapture system to extend its shelf life. Experimental Chemicals PA6 was made by electrospinning by Tecnalia Research & Innovation, the composition of the ultrathin NFs

• (immediately after antibody anchoring; it is considered the reference value) and 7 days, 30 days, and 90 days after antibody anchoring, bringing the immunocapture systems to room temperature only covered by aluminum foil. Washing steps were carried out between each step above in order to remove non-linked

Industrial perspectives for personalized microneedles

• Remmi Danae Baker-Sediako,
• Benjamin Richter,
• Matthias Blaicher,
• Michael Thiel and
• Martin Hermatschweiler

Beilstein J. Nanotechnol. 2023, 14, 857–864, doi:10.3762/bjnano.14.70

• anchoring in barbed microneedles when compared to smooth microneedles [34]. Thus, it would be exciting to design microneedles, particularly those for pain management in joints, that are able to withstand a patient’s movements. Bio-inspired designs do not need to be an exact replica of their animal muse to

Nanostructured lipid carriers containing benznidazole: physicochemical, biopharmaceutical and cellular in vitro studies

• Giuliana Muraca,
• María Esperanza Ruiz,
• Rocío C. Gambaro,
• Sebastián Scioli-Montoto,
• María Laura Sbaraglini,
• Gisel Padula,
• José Sebastián Cisneros,
• Cecilia Yamil Chain,
• Vera A. Álvarez,
• Cristián Huck-Iriart,
• Guillermo R. Castro,
• María Belén Piñero,
• Matias Ildebrando Marchetto,
• Catalina Alba Soto,
• Germán A. Islan and
• Alan Talevi

Beilstein J. Nanotechnol. 2023, 14, 804–818, doi:10.3762/bjnano.14.66

• indicated that the specificity of fatty acid incorporation depends on chain length [52]. The lipid in our formulation is an ester of fatty acids that could hypothetically interrupt the anchoring of mucin to the lipid bilayer in T. cruzi, thus rendering the parasites non-viable. However, further studies are

Antimicrobial and mechanical properties of functionalized textile by nanoarchitectured photoinduced Ag@polymer coating

• Jessica Plé,
• Marine Dabert,
• Helene Lecoq,
• Sophie Hellé,
• Lydie Ploux and
• Lavinia Balan

Beilstein J. Nanotechnol. 2023, 14, 95–109, doi:10.3762/bjnano.14.11

• polymer matrix are synthesized simultaneously, the polymer chains are able to insinuate themselves between the particles, effectively anchoring them to the rest of the coating. Abrasion The longevity of the functionalized textiles was next assessed by testing the abrasion resistance of the coatings, with

Spindle-like MIL101(Fe) decorated with Bi₂O₃ nanoparticles for enhanced degradation of chlortetracycline under visible-light irradiation

• Chen-chen Hao,
• Fang-yan Chen,
• Kun Bian,
• Yu-bin Tang and
• Wei-long Shi

Beilstein J. Nanotechnol. 2022, 13, 1038–1050, doi:10.3762/bjnano.13.91

• about the construction of Z-scheme heterojunctions by coupling MIL101(Fe) and Bi2O3. Herein, in order to enhance the photocatalytic efficiency of MIL101(Fe) for degradation of CTC, a novel 0D/3D heterojunction catalyst Bi2O3/MIL101(Fe) was prepared by anchoring Bi2O3 nanoparticles to the surface of

Electrocatalytic oxygen reduction activity of AgCoCu oxides on reduced graphene oxide in alkaline media

• Iyyappan Madakannu,
• Indrajit Patil,
• Bhalchandra Kakade and
• Kasibhatta Kumara Ramanatha Datta

Beilstein J. Nanotechnol. 2022, 13, 1020–1029, doi:10.3762/bjnano.13.89

• functional layered scaffold anchoring metal NPs (Figure S3a,b, Supporting Information File 1). Likewise, for the trimetallic NPs anchored on the rGO support, we observe various sizes and morphologies on multilayered rGO nanosheets. The variation in the morphology stems from the fusion of Cu and Co into Ag

• groups with strong affinity and the scaffolding nature of rGO anchoring trimetallic NPs. The large particle sizes of the trimetallic system could be due to the slower reduction and prolonged nucleation of the constituents. The heterogeneous nature of the electrocatalyst surface is clearly evident from

Hierarchical Bi₂WO₆/TiO₂-nanotube composites derived from natural cellulose for visible-light photocatalytic treatment of pollutants

• Zehao Lin,
• Zhan Yang and
• Jianguo Huang

Beilstein J. Nanotechnol. 2022, 13, 745–762, doi:10.3762/bjnano.13.66

• the uniform anchoring of Bi2WO6 nanoparticles on TiO2 nanotubes, as well as strong mutual effects and well-proportioned formation of heterostructures in between the Bi2WO6 and TiO2 phases. These improvements arose from the cellulose-derived unique structures, leading to an enhanced absorption of

Approaching microwave photon sensitivity with Al Josephson junctions

• Andrey L. Pankratov,
• Anna V. Gordeeva,
• Leonid S. Revin,
• Dmitry A. Ladeynov,
• Anton A. Yablokov and
• Leonid S. Kuzmin

Beilstein J. Nanotechnol. 2022, 13, 582–589, doi:10.3762/bjnano.13.50

• conclude that the optimal critical current range, allowing for improvement of both sensitivity and dark count time, is about hundreds of nanoamperes as predicted in [6]. Such junctions are currently being measured. (a) Scheme of the measurement electronics with thermal anchoring and various filtering

Micro- and nanotechnology in biomedical engineering for cartilage tissue regeneration in osteoarthritis

• Zahra Nabizadeh,
• Mahmoud Nasrollahzadeh,
• Hamed Daemi,
• Mohamadreza Baghaban Eslaminejad,
• Ali Akbar Shabani,
• Mehdi Dadashpour,
• Majid Mirmohammadkhani and
• Davood Nasrabadi

Beilstein J. Nanotechnol. 2022, 13, 363–389, doi:10.3762/bjnano.13.31

Molecular assemblies on surfaces: towards physical and electronic decoupling of organic molecules

• Sabine Maier and
• Meike Stöhr

Beilstein J. Nanotechnol. 2021, 12, 950–956, doi:10.3762/bjnano.12.71

• feature heterogeneous adsorption sites, which can lead to the anchoring of organic molecules having specific functional groups. Hence, the interplay of the potential energy landscape of the substrate and the intermolecular interactions steers the self-assembly in such systems. Xiang et al. [90] studied

Influence of electrospray deposition on C₆₀ molecular assemblies

• Antoine Hinaut,
• Sebastian Scherb,
• Sara Freund,
• Zhao Liu,
• Thilo Glatzel and
• Ernst Meyer

Beilstein J. Nanotechnol. 2021, 12, 552–558, doi:10.3762/bjnano.12.45

• filled with C60 (see white arrows). Step edges are known to be favorable anchoring sites and to easily trap molecules. Second, C60 molecules are observed in islands formed on the Au(111) surface and aligned along the step edges of the surface. Islands are observed at the bottom or on top of step edges

• of the islands is found. Similar results are obtained for a Ag(111) surface, as shown in part 2 of Supporting Information File 1. The absence of favorable anchoring sites, similar to kinks in the herringbone reconstruction, on Ag(111) suggests that not only the adsorbed solvent molecules are

Extended iron phthalocyanine islands self-assembled on a Ge(001):H surface

• Rafal Zuzak,
• Marek Szymonski and
• Szymon Godlewski

Beilstein J. Nanotechnol. 2021, 12, 232–241, doi:10.3762/bjnano.12.19

• anchoring sites for the FePc molecules visible within Figure 6a. As visible in Figure 6, the manipulation described above is not the only modification recorded in the scanned area. We can notice two other molecules located in the central part of Figure 6a, which are displaced during scanning and disappear

Cu₂O nanoparticles for the degradation of methyl parathion

• Juan Rizo,
• David Díaz,
• Benito Reyes-Trejo and
• M. Josefina Arellano-Jiménez

Beilstein J. Nanotechnol. 2020, 11, 1546–1555, doi:10.3762/bjnano.11.137

• passivation of the Cu2O surface because the degradation of methyl parathion does not occur when CuO is used instead of Cu2O in the dispersion medium. Second, CuO could play an important role in the degradation mechanism by anchoring MP molecules on the surface of Cu2O through a coordinated bond between Cu2

Adsorption and self-assembly of porphyrins on ultrathin CoO films on Ir(100)

• Feifei Xiang,
• Tobias Schmitt,
• Marco Raschmann and
• M. Alexander Schneider

Beilstein J. Nanotechnol. 2020, 11, 1516–1524, doi:10.3762/bjnano.11.134

• , due to the rather flat potential landscape, molecular rotation is thermally activated, which effectively prevents self-assembly. The situation is different for 2H-TCNPP, which, due to the additional functional anchoring groups, does not self-assemble on the 1BL film but forms self-assembled compact

• islands on the 2BL film. The findings demonstrate the guiding effect of the cobalt oxide films of different thickness and the effect of functional surface anchoring. Keywords: adsorption energy; molecular rotors; porphyrins; self-assembly; transition metal oxides; Introduction Due to their variability

• molecular adlayer, for example, by introducing elements that allow for strong anchoring [8][10][11][12][13]. This may, however, counteract the possibility to form ordered layers when, due to the enhanced molecule–substrate interaction, the molecules become immobile or the functional groups used as anchors

A wideband cryogenic microwave low-noise amplifier

• Boris I. Ivanov,
• Dmitri I. Volkhin,
• Ilya L. Novikov,
• Dmitri K. Pitsun,
• Dmitri O. Moskalev,
• Ilya A. Rodionov,
• Evgeni Il’ichev and
• Aleksey G. Vostretsov

Beilstein J. Nanotechnol. 2020, 11, 1484–1491, doi:10.3762/bjnano.11.131

• signal lines installed into the dilution refrigerator for the S-parameter and noise temperature measurements of the amplifier. The simplified measurement scheme is presented in Figure 3. In order to reduce the input signal level, to perform thermal anchoring at each stage, and to prepare the noise

One-step synthesis of carbon-supported electrocatalysts

• Sebastian Tigges,
• Nicolas Wöhrl,
• Ivan Radev,
• Ulrich Hagemann,
• Markus Heidelmann,
• Thai Binh Nguyen,
• Stanislav Gorelkov,
• Stephan Schulz and
• Axel Lorke

Beilstein J. Nanotechnol. 2020, 11, 1419–1431, doi:10.3762/bjnano.11.126

• discussed in the following. Traditional multistep synthesis methods for Pt/C catalysts use supports, which are partially graphitized for reaching the required high electrical conductivity and durability. Therefore, the support surface is characterized by a low density of binding sites for anchoring Pt-NP

• results in a high density of anchoring sites for the co-deposited metal nanoparticles, which are partially embedded subsequently in the pristine carbon support with a high graphitization degree, and therefore, with high corrosion stability. Consequently, embedding Pt-NP in the C-matrix not only results in

Cryogenic low-noise amplifiers for measurements with superconducting detectors

• Ilya L. Novikov,
• Boris I. Ivanov,
• Dmitri V. Ponomarev and
• Aleksey G. Vostretsov

Beilstein J. Nanotechnol. 2020, 11, 1316–1320, doi:10.3762/bjnano.11.115

• cryostat with He-7 sorption unit. The amplifier was fixed to the cooling plate with brass screws to have good thermal anchoring. The signal lines were connected to the cryostat CuBe coaxial cables. The amplifier gain curves measured at three temperatures are presented in Figure 4. The maximum gain of the

Adsorption behavior of tin phthalocyanine onto the (110) face of rutile TiO₂

• Lukasz Bodek,
• Mads Engelund,
• Aleksandra Cebrat and
• Bartosz Such

Beilstein J. Nanotechnol. 2020, 11, 821–828, doi:10.3762/bjnano.11.67

• through the correct orientation is quite small. This is in contrast to molecules possessing anchoring moieties at the edges for which the rotation can lead to significant changes. Such a phenomenon was observed for CuTPP deposited onto the TiO2(110) surface [34], where molecular rotation allowed for the

Silver-decorated gel-shell nanobeads: physicochemical characterization and evaluation of antibacterial properties

• Marta Bartel,
• Katarzyna Markowska,
• Marcin Strawski,
• Krystyna Wolska and
• Maciej Mazur

Beilstein J. Nanotechnol. 2020, 11, 620–630, doi:10.3762/bjnano.11.49

• layer producing silver nanoparticles but also transforms a fraction of sulfonic groups in the polymer to moieties with sulfur in a lower oxidation state, likely thiols. It is hypothesized that the generated thiol groups are anchoring the nanoparticles in the gel shell of the nanobeads stabilizing the

• have been partially reduced to thiol moieties. In consequence, the thiols interact with the silver nanoparticles anchoring them in the gel layer on the nanobeads. Moreover, it has been shown that the nanocomposite exhibits considerable antibacterial activity, comparable or superior to that of non

• reduced to moieties of lower oxidation state, likely thiols. It seems that the thiol groups may interact with the surface of the nanoparticles anchoring them in the gel layer of the beads and stabilizing the whole structure. One should note that the interaction of silver with thiol groups is much stronger

Rational design of block copolymer self-assemblies in photodynamic therapy

• Maxime Demazeau,
• Laure Gibot,
• Anne-Françoise Mingotaud,
• Patricia Vicendo,
• Clément Roux and
• Barbara Lonetti

Beilstein J. Nanotechnol. 2020, 11, 180–212, doi:10.3762/bjnano.11.15

Integration of sharp silicon nitride tips into high-speed SU8 cantilevers in a batch fabrication process

• Nahid Hosseini,
• Matthias Neuenschwander,
• Oliver Peric,
• Santiago H. Andany,
• Jonathan D. Adams and
• Georg E. Fantner

Beilstein J. Nanotechnol. 2019, 10, 2357–2363, doi:10.3762/bjnano.10.226

• developed a batch fabrication process to integrate silicon nitride tips with an average tip radius of 9 ± 2 nm into high-speed SU8 cantilevers. Key aspects of the process are the mechanical anchoring of a moulded silicon nitride tip and a two-step release process. The fabrication recipe can be adjusted to

Microbubbles decorated with dendronized magnetic nanoparticles for biomedical imaging: effective stabilization via fluorous interactions

• Da Shi,
• Justine Wallyn,
• Dinh-Vu Nguyen,
• Francis Perton,
• Delphine Felder-Flesch,
• Sylvie Bégin-Colin,
• Mounir Maaloum and
• Marie Pierre Krafft

Beilstein J. Nanotechnol. 2019, 10, 2103–2115, doi:10.3762/bjnano.10.205

• into the phospholipid shell of the MBs. OEG chains were selected in order to improve the dispersibility of the IONPs in water [27][28]. Dendritic phosphonates are effective anchoring agents due to the covalent PO–metal bonds that stabilize aqueous dispersions of IONPs [27][29]. Such dendronized IONPs

• have been investigated for hyperthermia and magnetic resonance imaging owing to their increased stability in aqueous media and biocompatibility [27][28]. An even stronger anchoring agent consisting of a dendron structure bearing a bisphosphonate polar head provided increased colloidal stability in

• dendrons investigated (CnX2n+1OEG8Den, X = F or H; n = 2 and 4); b) Schematic representation of a dendronized IONP showing the anchoring of the bisphosphonate function on the iron oxide. Hydrodynamic diameter distributions of IONPs grafted with dendrons: C2H5OEG8Den (38 ± 1 nm, black), C2F5OEG8Den (37 ± 1