High-temperature epitaxial growth of tantalum nitride thin films on MgO: structural evolution and potential for SQUID applications

• Michelle Cedillo Rosillo,
• Oscar Contreras López,
• Jesús Antonio Díaz,
• Agustín Conde Gallardo and
• Harvi A. Castillo Cuero

Beilstein J. Nanotechnol. 2025, 16, 690–699, doi:10.3762/bjnano.16.53

• dynamics and superconducting characteristics of the films. X-ray diffraction (XRD) analysis revealed that the TaN thin films exhibited excellent crystallinity, with sharp diffraction peaks indicating well-defined structural phases. The deposition process was optimized by systematically adjusting substrate

Aprepitant-loaded solid lipid nanoparticles: a novel approach to enhance oral bioavailability

• Mazhar Hussain,
• Muhammad Farooq,
• Muhammad Asad Saeed,
• Muhammad Ijaz,
• Sherjeel Adnan,
• Zeeshan Masood,
• Muhammad Waqas,
• Wafa Ishaq and
• Nabeela Ameer

Beilstein J. Nanotechnol. 2025, 16, 652–663, doi:10.3762/bjnano.16.50

• microscopy (SEM), X-ray diffraction (XRD), differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA), in vitro drug release in 0.1 M HCl (pH 1.2) and phosphate-buffered saline (PBS, pH 7.4), and pharmacokinetic studies. The optimal formulation (APT-CD-NP4) containing the highest

• , and zeta potential measurements. Also Fourier-transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD), solubility, in vitro dissolution, and in vivo and stability studies were carried out. Result and Discussion Physicochemical evaluation The solubility of APT in the SLNs was 24-fold higher

• studies Fourier-transform infrared spectroscopy (FTIR) was performed using an Agilent Technologies Cary 660 apparatus to detect the physicochemical interaction between APT and β-CD and poloxamer 407. The spectra were recorded in a wave number range of 4000 to 400 cm−1. X-ray diffraction (XRD, D/MAX-2500

Retrieval of B1 phase from high-pressure B2 phase for CdO nanoparticles by electronic excitations in Cd_xZn_1−xO composite thin films

• Arkaprava Das,
• Marcin Zając and
• Carla Bittencourt

Beilstein J. Nanotechnol. 2025, 16, 551–560, doi:10.3762/bjnano.16.43

• film prior to further irradiation. The characterization of the thin films was performed using X-ray diffraction (XRD) on a Bruker high-resolution X-ray diffractometer, employing a Cu Kα beam over a 2θ range of 30–50°. Raman spectroscopic measurements were conducted at room temperature with a SENTERRA

Zeolite materials with Ni and Co: synthesis and catalytic potential in the selective hydrogenation of citral

• Inocente Rodríguez-Iznaga,
• Yailen Costa Marrero,
• Tania Farias Piñeira,
• Céline Fontaine,
• Lexane Paget,
• Beatriz Concepción Rosabal,
• Arbelio Penton Madrigal,
• Vitalii Petranovskii and
• Gwendoline Lafaye

Beilstein J. Nanotechnol. 2025, 16, 520–529, doi:10.3762/bjnano.16.40

• nitrogen adsorption at 77 K. The initial natural zeolite samples were also examined via powder X-ray diffraction (XRD) and scanning electron microscopy (SEM). XRD patterns were recorded using a PW 1218 diffractometer (Philips, Almelo, Netherlands) equipped with a curved graphite monochromator and Cu Kα

N₂⁺-implantation-induced tailoring of structural, morphological, optical, and electrical characteristics of sputtered molybdenum thin films

• Usha Rani,
• Kafi Devi,
• Divya Gupta and
• Sanjeev Aggarwal

Beilstein J. Nanotechnol. 2025, 16, 495–509, doi:10.3762/bjnano.16.38

• implantation, the stress in the films changed from tensile to compressive, as illustrated in Figure 4. The X-ray diffraction (XRD) peak position shift provides further insight into these stress changes. In as-deposited films, the peaks are shifting to lower 2θ values, signifying an increase in interatomic

Size control of nanoparticles synthesized by pulsed laser ablation in liquids using donut-shaped beams

• Abdel Rahman Altakroury,
• Oleksandr Gatsa,
• Farbod Riahi,
• Zongwen Fu,
• Miroslava Flimelová,
• Andrei Samokhvalov,
• Stephan Barcikowski,
• Carlos Doñate-Buendía,
• Alexander V. Bulgakov and
• Bilal Gökce

Beilstein J. Nanotechnol. 2025, 16, 407–417, doi:10.3762/bjnano.16.31

• crystal structure of the HEA NPs was determined by X-ray diffraction (XRD) using a Smartlab diffractometer (Rigaku, Japan). SEM was used to characterize the nanoparticle size distribution and to determine the beam shape influence while maintaining comparable PLAL parameters for both beams to minimize the

Pulsed laser in liquid grafting of gold nanoparticle–carbon support composites

• Madeleine K. Wilsey,
• Teona Taseska,
• Qishen Lyu,
• Connor P. Cox and
• Astrid M. Müller

Beilstein J. Nanotechnol. 2025, 16, 349–361, doi:10.3762/bjnano.16.26

• gold nanoparticles) spectral signatures were not observable here. Pulsed laser grafting created nonequilibrium gold nanoparticle–carbon fiber paper composites, evident from powder X-ray diffraction (XRD) data (Figure 5A). We normalized the XRD patterns to the (111) peak and found that the (200) or (311

• ) using instrument-specific atomic sensitivity factors. X-ray diffraction (XRD) measurements were conducted at the Chemical Analysis Lab at the Rochester Institute of Technology using a Bruker D8 ADVANCE diffractometer with Cu Kα radiation (40 kV and 40 mA). The configuration included a 0.6 mm primary

Synthesis and the impact of hydroxyapatite nanoparticles on the viability and activity of rhizobacteria

• Bedah Rupaedah,
• Indrika Novella,
• Atiek Rostika Noviyanti,
• Diana Rakhmawaty Eddy,
• Anna Safarrida,
• Abdul Hapid,
• Zhafira Amila Haqqa,
• Suryana Suryana,
• Irwan Kurnia and
• Fathiyah Inayatirrahmi

Beilstein J. Nanotechnol. 2025, 16, 216–228, doi:10.3762/bjnano.16.17

• gradually through a solvothermal reaction, driven by the chemical transformation represented by the following equation: Nanohydroxyapatite characterization The structural analysis of nHA was performed using X-ray diffraction (XRD). The diffraction pattern of nHA standard is given in Figure 1, while that of

• Novella and coworkers [26]. Nanohydroxyapatite characterization Structural assessment of the synthesized nHA was conducted using X-ray diffraction (XRD) with the PANalytical AERIS system and OriginLab 8.5.1 software. Further examination of the sample’s morphology was carried out using a scanning electron

A review of metal-organic frameworks and polymers in mixed matrix membranes for CO₂ capture

• Charlotte Skjold Qvist Christensen,
• Nicholas Hansen,
• Mahboubeh Motadayen,
• Nina Lock,
• Martin Lahn Henriksen and
• Jonathan Quinson

Beilstein J. Nanotechnol. 2025, 16, 155–186, doi:10.3762/bjnano.16.14

• , and X-ray diffraction (XRD) provide information about the bulk MOF-based MMM [140][141][142]. FTIR yields information about the functional groups within the sample [140], and will differ between the pristine MOF, polymer membrane, and MOF-based MMM [118][121][122][124][128][131]. In this way, it is

Clays enhanced with niobium: potential in wastewater treatment and reuse as pigment with antibacterial activity

• Silvia Jaerger,
• Patricia Appelt,
• Mario Antônio Alves da Cunha,
• Fabián Ccahuana Ayma,
• Ricardo Schneider,
• Carla Bittencourt and
• Fauze Jacó Anaissi

Beilstein J. Nanotechnol. 2025, 16, 141–154, doi:10.3762/bjnano.16.13

• dye with the enzyme succinate dehydrogenase (present in the mitochondria), leading to the formation of a salt called Formazan with a pink-reddish color. Characterization X-ray diffraction (XRD) measurements of the powder were conducted using a Rigaku BEartLab SE 3 kW diffractometer equipped with Cu Kα

TiO₂ immobilized on 2D mordenite: effect of hydrolysis conditions on structural, textural, and optical characteristics of the nanocomposites

• Marina G. Shelyapina,
• Rosario Isidro Yocupicio-Gaxiola,
• Gleb A. Valkovsky and
• Vitalii Petranovskii

Beilstein J. Nanotechnol. 2025, 16, 128–140, doi:10.3762/bjnano.16.12

• -angle and full X-ray diffraction (XRD) patterns, respectively, for the samples containing hydrolyzed forms of Ti after hydrolysis of TEOT. The full XRD patterns of the hydrolyzed samples after calcination are shown in Figure 1c. For comparison, the corresponding patterns for the parent compound MOR-L

Fabrication of hafnium-based nanoparticles and nanostructures using picosecond laser ablation

• Abhishek Das,
• Mangababu Akkanaboina,
• Jagannath Rathod,
• R. Sai Prasad Goud,
• Kanaka Ravi Kumar,
• Raghu C. Reddy,
• Ratheesh Ravendran,
• Katia Vutova,
• S. V. S. Nageswara Rao and
• Venugopal Rao Soma

Beilstein J. Nanotechnol. 2024, 15, 1639–1653, doi:10.3762/bjnano.15.129

• . These Hf sponges, cut and polished to 10 mm × 10 mm × 2 mm, were used as ablation targets. The pristine target had the crystal structure of hexagonal HfO0.25, as confirmed by X-ray diffraction (XRD) data (see Figure 1a). The elemental composition (Hf: 73.68%, O: 26.32%) was determined by energy

Facile synthesis of size-tunable L-carnosine-capped silver nanoparticles and their role in metal ion sensing and catalytic degradation of p-nitrophenol

• Akash Kumar,
• Ridhima Chadha,
• Abhishek Das,
• Nandita Maiti and
• Rayavarapu Raja Gopal

Beilstein J. Nanotechnol. 2024, 15, 1576–1592, doi:10.3762/bjnano.15.124

• , Netherlands) for a detailed examination of size and morphology. The crystalline structure of ʟ-car-AgNP1 was determined using X-ray diffraction (XRD, Rigaku Smartlab, Japan) within a 2θ range of 35° to 80°. Nanoparticle solutions were air-dried, and the obtained nanopowders (20 mg) were used for measurements

Mn-doped ZnO nanopowders prepared by sol–gel and microwave-assisted sol–gel methods and their photocatalytic properties

• Cristina Maria Vlăduț,
• Crina Anastasescu,
• Silviu Preda,
• Oana Catalina Mocioiu,
• Simona Petrescu,
• Jeanina Pandele-Cusu,
• Dana Culita,
• Veronica Bratan,
• Ioan Balint and
• Maria Zaharescu

Beilstein J. Nanotechnol. 2024, 15, 1283–1296, doi:10.3762/bjnano.15.104

• using X-ray diffraction (XRD). The resulting XRD patterns, shown in Figure 6a, indicate that the samples are polycrystalline and single-phase. This single phase corresponds well to the data from ICDD file no. 36-1451 of zincite ZnO. ZnO has a wurtzite-type structure and crystallizes in the hexagonal P63

• 10 and 20 kV in high vacuum mode. X-ray diffraction (XRD) measurements were carried out using an Ultima IV diffractometer (Rigaku Corp., Japan) equipped with parallel beam optics, using Cu Kα radiation (λ = 1.5418 Å) at 40 kV and 30 mA over the 2θ range of 25–80° at a scanning rate of 2°/min with a

Intermixing of MoS₂ and WS₂ photocatalysts toward methylene blue photodegradation

• Maryam Al Qaydi,
• Nitul S. Rajput,
• Michael Lejeune,
• Abdellatif Bouchalkha,
• Mimoun El Marssi,
• Steevy Cordette,
• Chaouki Kasmi and
• Mustapha Jouiad

Beilstein J. Nanotechnol. 2024, 15, 817–829, doi:10.3762/bjnano.15.68

• , the positions of the E12g and A1g vibrational modes in the composite sample did not exhibit any noticeable shifts compared to the observed peaks in individual samples as reported in previous studies [26]. The X-ray diffraction (XRD) diagram shown in Figure 2a exhibits the diffraction peaks at 14.25

Elastic modulus of β-Ga₂O₃ nanowires measured by resonance and three-point bending techniques

• Annamarija Trausa,
• Sven Oras,
• Sergei Vlassov,
• Mikk Antsov,
• Tauno Tiirats,
• Andreas Kyritsakis,
• Boris Polyakov and
• Edgars Butanovs

Beilstein J. Nanotechnol. 2024, 15, 704–712, doi:10.3762/bjnano.15.58

• -Ga2O3 NW synthesis methods and detailed post-examination of their mechanical properties before considering their application in future nanoscale devices. Results For structural analysis of the as-grown NW arrays on Si(100)/SiO2 substrates, X-ray diffraction (XRD) measurements were conducted. The marked

Gold nanomakura: nanoarchitectonics and their photothermal response in association with carrageenan hydrogels

• Nabojit Das,
• Vikas,
• Akash Kumar,
• Sanjeev Soni and
• Raja Gopal Rayavarapu

Beilstein J. Nanotechnol. 2024, 15, 678–693, doi:10.3762/bjnano.15.56

• . Also, the photothermal responses of the nanoparticles in association with k-CG hydrogels were assessed, indicating their potential in biomedical applications. Furthermore, characterization such as zeta potential, crystallinity, and surface functionalization were investigated through ZetaSizer, X-ray

• diffraction (XRD), and FTIR, respectively, to establish physicochemical properties of the synthesized nanomaterials. Results Synthesis, optical spectroscopy, and zeta potential Anisotropic gold nanoparticles of makura shape were synthesized using seed-mediated approach as shown in Figure 1a. The Au seeds were

Exfoliation of titanium nitride using a non-thermal plasma process

• Priscila Jussiane Zambiazi,
• Dolores Ribeiro Ricci Lazar,
• Larissa Otubo,
• Rodrigo Fernando Brambilla de Souza,
• Almir Oliveira Neto and
• Cecilia Chaves Guedes-Silva

Beilstein J. Nanotechnol. 2024, 15, 631–637, doi:10.3762/bjnano.15.53

• microscope operating at 200 kV. X-ray diffraction (XRD) analysis was conducted using a diffractometer (Miniflex II) with Cu Kα radiation over a 2θ range of 20–90°, with a scan speed of 2° per minute. Furthermore, Raman spectra were obtained using a spectrometer (Horiba Scientific MacroRam Raman) equipped

Radiofrequency enhances drug release from responsive nanoflowers for hepatocellular carcinoma therapy

• Yanyan Wen,
• Ningning Song,
• Yueyou Peng,
• Weiwei Wu,
• Qixiong Lin,
• Minjie Cui,
• Rongrong Li,
• Qiufeng Yu,
• Sixue Wu,
• Yongkang Liang,
• Wei Tian and
• Yanfeng Meng

Beilstein J. Nanotechnol. 2024, 15, 569–579, doi:10.3762/bjnano.15.49

• substituted by O–H. Additionally, other characteristic absorption peaks of CUR and HPS were retained. These findings confirmed the successful synthesis of CUR-Fe@MnO2 NFs. According to the X-ray diffraction (XRD) pattern (Figure 2g), the 2θ diffraction peaks at 30.1° (220), 35.4° (311), 37.0° (222), 43.1

Aero-ZnS prepared by physical vapor transport on three-dimensional networks of sacrificial ZnO microtetrapods

• Veaceslav Ursaki,
• Tudor Braniste,
• Victor Zalamai,
• Emil Rusu,
• Vladimir Ciobanu,
• Vadim Morari,
• Daniel Podgornii,
• Pier Carlo Ricci,
• Rainer Adelung and
• Ion Tiginyanu

Beilstein J. Nanotechnol. 2024, 15, 490–499, doi:10.3762/bjnano.15.44

• produced material is investigated by scanning electron microscopy (SEM), while its crystalline and optical qualities are assessed by X-ray diffraction (XRD) analysis and photoluminescence (PL) spectroscopy, respectively. We demonstrate possibilities for controlling the composition and the crystallographic

• sensor applications. Keywords: aeromaterial; crystallographic structure; luminescence; physical vapor transport; scanning electron microscopy (SEM); X-ray diffraction (XRD); Introduction Porous materials represent a class of solid-state networks widely used in adsorptive and photocatalytic removal of

Photocatalytic degradation of methylene blue under visible light by cobalt ferrite nanoparticles/graphene quantum dots

• Vo Chau Ngoc Anh,
• Le Thi Thanh Nhi,
• Le Thi Kim Dung,
• Dang Thi Ngoc Hoa,
• Nguyen Truong Son,
• Nguyen Thi Thao Uyen,
• Nguyen Ngoc Uyen Thu,
• Le Van Thanh Son,
• Le Trung Hieu,
• Tran Ngoc Tuyen and
• Dinh Quang Khieu

Beilstein J. Nanotechnol. 2024, 15, 475–489, doi:10.3762/bjnano.15.43

• benzoquinone (C6H4O2) was provided by Sigma-Aldrich, USA. Sodium hydroxide (NaOH, ≥96%) and hydrogen chloride (HCl, 38%) were purchased from Xilong, China. Instruments X-ray diffraction (XRD) patterns were recorded by using a D8 Advance (Bruker, Germany) with Cu Kα radiation (λ = 0.154 nm). Fourier-transform

Controllable physicochemical properties of WO_x thin films grown under glancing angle

• Rupam Mandal,
• Aparajita Mandal,
• Alapan Dutta,
• Rengasamy Sivakumar,
• Sanjeev Kumar Srivastava and
• Tapobrata Som

Beilstein J. Nanotechnol. 2024, 15, 350–359, doi:10.3762/bjnano.15.31

• bias voltage was applied to the p-Si substrates, whereas the WOx films were kept grounded. The crystallinity of the WOx films was examined using X-ray diffraction (XRD) (Bruker) under Bragg–Brentano geometry (θ–2θ) in an angular window of 2θ = 20° to 80°. The chemical composition of the WOx films was

Vinorelbine-loaded multifunctional magnetic nanoparticles as anticancer drug delivery systems: synthesis, characterization, and in vitro release study

• Zeynep Özcan and
• Afife Binnaz Hazar Yoruç

Beilstein J. Nanotechnol. 2024, 15, 256–269, doi:10.3762/bjnano.15.24

• -resolution analytical electron microscope (FE-SEM, Thermo Scientific, Apreo 2S LoVac) and a scanning transmission electron microscope (STEM, Phillips XL, 30 ESEM-FEG/EDAX) operating at 120 kV acceleration voltage. The structure of the nanoparticles was analyzed by X-ray diffraction (XRD, PANalytical, Xpert

• between peak broadening and particle size in X-ray analysis. In this equation, the symbols D, K, λ, β, and θ represent the particle size, Scherrer shape factor (here 0.89), X-ray wavelength (0.15418 nm), half-maximum width, and diffraction angle, respectively [43]. Using the X-ray diffraction (XRD

Modification of graphene oxide and its effect on properties of natural rubber/graphene oxide nanocomposites

• Nghiem Thi Thuong,
• Le Dinh Quang,
• Vu Quoc Cuong,
• Cao Hong Ha,
• Nguyen Ba Lam and
• Seiichi Kawahara

Beilstein J. Nanotechnol. 2024, 15, 168–179, doi:10.3762/bjnano.15.16

• characterized by X-ray diffraction (XRD), Fourier-transform infrared spectroscopy, contact angle, thermal gravimetric analysis, and scanning electron microscopy. The XRD results showed the appearance of an amorphous region of silica particles at a diffraction angle of 22°. The formation of silica was

• conditions to determine the ideal condition to modify GO for grafting onto NR. The GO-VTES products were characterized using X-ray diffraction (XRD), contact angle, 29Si NMR, Fourier-transform infrared spectroscopy (FTIR), and morphology analysis. The GO-VTES was expected to improve the mechanical properties

Berberine-loaded polylactic acid nanofiber scaffold as a drug delivery system: The relationship between chemical characteristics, drug-release behavior, and antibacterial efficiency

• Le Thi Le,
• Hue Thi Nguyen,
• Liem Thanh Nguyen,
• Huy Quang Tran and
• Thuy Thi Thu Nguyen

Beilstein J. Nanotechnol. 2024, 15, 71–82, doi:10.3762/bjnano.15.7

• separation during the electrospinning process [17][38][39], leading to the formation of a BBR-rich phase on the surface of nanofibers. The crystallinity of the PLA pellet and electrospun nanofiber scaffolds were examined by X-ray diffraction (XRD) analysis (Figure 3B). The XRD pattern of the PLA pellet shows