Enhancing higher-order modal response in multifrequency atomic force microscopy with a coupled cantilever system

• Wendong Sun,
• Jianqiang Qian,
• Yingzi Li,
• Yanan Chen,
• Zhipeng Dou,
• Rui Lin,
• Peng Cheng,
• Xiaodong Gao,
• Quan Yuan and
• Yifan Hu

Beilstein J. Nanotechnol. 2024, 15, 694–703, doi:10.3762/bjnano.15.57

• parameters Several commercial rectangular multifrequency AFM cantilevers of different sizes from different manufacturers are summarized in [24]. In the ANSYS Workbench finite element simulation, the material used in the simulation is silicon, with a Young's modulus of 166 GPa and a density of 2330 kg/m3. We

Determination of elastic moduli of elastic–plastic microspherical materials using nanoindentation simulation without mechanical polishing

• Hongzhou Li and
• Jialian Chen

Beilstein J. Nanotechnol. 2021, 12, 213–221, doi:10.3762/bjnano.12.17

• finite element method [14][15][16][17][18][19][20][21][22][23][24][25]. Using finite element simulation, Li et al. found that both loading curve and unloading curve at any depth can be generated from one indentation depth by scaling P ∝ h2 for the indentation tests of PMMA thin films with a Berkovich

Numerical analysis of vibration modes of a qPlus sensor with a long tip

• Kebei Chen,
• Zhenghui Liu,
• Yuchen Xie,
• Chunyu Zhang,
• Gengzhao Xu,
• Wentao Song and
• Ke Xu

Beilstein J. Nanotechnol. 2021, 12, 82–92, doi:10.3762/bjnano.12.7

• . Mechanical vibration excitation is applied on one side of the tuning fork. (b) Map of the mesh distribution as implemented in the finite element simulation. (c) Zoomed-in view of the tungsten wire attached to the end of the tuning fork. (d) False-color representation of the total displacement levels when the

Nonclassical dynamic modeling of nano/microparticles during nanomanipulation processes

• Moharam Habibnejad Korayem,
• Ali Asghar Farid and
• Rouzbeh Nouhi Hefzabad

Beilstein J. Nanotechnol. 2020, 11, 147–166, doi:10.3762/bjnano.11.13

• . Mechanical modeling and finite element simulation were employed to analyze the behavior of samples and optimize the manipulation method. The model used for mechanical modeling was the classical Euler–Bernoulli beam model [18]. AFM cantilever dimensions are at micrometer scale and designers are constantly

Electrostatic force microscopy for the accurate characterization of interphases in nanocomposites

• Diana El Khoury,
• Richard Arinero,
• Jean-Charles Laurentie,
• Mikhaël Bechelany,
• Michel Ramonda and
• Jérôme Castellon

Beilstein J. Nanotechnol. 2018, 9, 2999–3012, doi:10.3762/bjnano.9.279

• deduced by comparison of experimental data and numerical simulations, as well as the interface state of silicone dioxide layers. Keywords: atomic force microscopy; building-block materials; dielectric permittivity; electrostatic force microscopy; finite element simulation; interphases; nanocomposites

Perfusion double-channel micropipette probes for oxygen flux mapping with single-cell resolution

• Yang Gao,
• Bin Li,
• Riju Singhal,
• Adam Fontecchio,
• Ben Pelleg,
• Zulfiya Orynbayeva,
• Yury Gogotsi and
• Gary Friedman

Beilstein J. Nanotechnol. 2018, 9, 850–860, doi:10.3762/bjnano.9.79

• element simulation of convection–diffusion equations. Inset (2) also illustrates that an oxygen sensor positioned downstream from the cell can be used to determine the cell’s oxygen consumption rate when the sensor’s measurement refers to the oxygen concentration at the top of the theta pipette. b) SEM

• outlet channels in both channels as well as a sensor in the outlet channel. The inset (2) illustrates the differences in oxygen concentration upstream and downstream from the cell within the theta pipette. The different colors represent different oxygen concentrations that are obtained from a finite

Thermo-voltage measurements of atomic contacts at low temperature

• Ayelet Ofarim,
• Bastian Kopp,
• Thomas Möller,
• León Martin,
• Johannes Boneberg,
• Paul Leiderer and
• Elke Scheer

Beilstein J. Nanotechnol. 2016, 7, 767–775, doi:10.3762/bjnano.7.68

• into the Seebeck coefficient S = −ΔV/ΔT, the determination of the temperature plays an important role. We present a method for the determination of the temperature difference using a combination of a finite element simulation, which reveals the temperature distribution of the sample, and the