Characterization of ion track-etched conical nanopores in thermal and PECVD SiO₂ using small angle X-ray scattering

• Shankar Dutt,
• Rudradeep Chakraborty,
• Christian Notthoff,
• Pablo Mota-Santiago,
• Christina Trautmann and
• Patrick Kluth

Beilstein J. Nanotechnol. 2025, 16, 899–909, doi:10.3762/bjnano.16.68

• and a wider size distribution. Results and Discussions Figure 1 shows plan-view scanning electron microscopy (SEM) images of nanopores fabricated in thermal (Figure 1a) and PECVD (Figure 1b) SiO2 by etching ion tracks produced with 1.6 GeV Au ion irradiation (see Experimental and Theory section for

• measured pore radii, we estimate track etch rates of 69 ± 3 nm/min for thermal and 90 ± 6 nm/min for PECVD SiO2, respectively. While the scanning electron microscopy images reveal the variation in nanopore size for PECVD SiO2 compared to thermal SiO2, as well as differences in nanopore morphology, these

• with the estimates from scanning electron microscopy analysis. It is important to emphasize that SAXS analysis provides a statistically robust characterization of polydispersity, radius, and cone angle values by sampling over 106 nanopores – a population size unattainable through microscopy analysis. A

Heat-induced transformation of nickel-coated polycrystalline diamond film studied in situ by XPS and NEXAFS

• Olga V. Sedelnikova,
• Yuliya V. Fedoseeva,
• Dmitriy V. Gorodetskiy,
• Yuri N. Palyanov,
• Elena V. Shlyakhova,
• Eugene A. Maksimovskiy,
• Anna A. Makarova,
• Lyubov G. Bulusheva and
• Aleksandr V. Okotrub

Beilstein J. Nanotechnol. 2025, 16, 887–898, doi:10.3762/bjnano.16.67

• process occurring at the interface between diamond and Ni nanoparticles was revealed using high-resolution transmission electron microscopy (HRTEM) [19][24]. During annealing, Ni nanoparticles etch the diamond surface, resulting in the formation of a narrow interdiffusion zone. The carbon atoms released

• . Additionally, angle-resolved NEXAFS spectra of annealed Ni-coated SCD were measured to reveal the orientation of the formed graphitic layers. After synchrotron measurements, the samples were exposed to air and further analyzed using Raman spectroscopy and scanning electron microscopy (SEM). The obtained

• coating upon annealing. This result confirms previously reported findings, which demonstrated the catalytic role of nickel in the reconstruction of a diamond surface [17][18][19][20][21][22][23][24]. Based on electron microscopy and Raman spectroscopy data, the authors of those studies claimed that

Ar⁺ implantation-induced tailoring of RF-sputtered ZnO films: structural, morphological, and optical properties

• Manu Bura,
• Divya Gupta,
• Arun Kumar and
• Sanjeev Aggarwal

Beilstein J. Nanotechnol. 2025, 16, 872–886, doi:10.3762/bjnano.16.66

• studied using field-emission scanning electron microscopy (FESEM) along with energy dispersive X-ray spectroscopy (EDS). Cross-sectional images are also obtained to evaluate the thickness of ZnO film. The optical properties of pristine and implanted ZnO films are investigated using a Shimadzu UV–visible

• competition between surface diffusion and ion erosion processes [34][35]. Field-emission scanning electron microscopy The surface morphology of pristine and 30 keV argon-implanted ZnO films was also studied by FESEM. Figure 8 shows the FESEM images of pristine and implanted films. To deduce the change in

Insights into the electronic and atomic structures of cerium oxide-based ultrathin films and nanostructures using high-brilliance light sources

• Paola Luches and
• Federico Boscherini

Beilstein J. Nanotechnol. 2025, 16, 860–871, doi:10.3762/bjnano.16.65

• spectra in photoemission electron microscopy (PEEM) mode, in which the photon energy is scanned across the XAS edge and the intensity of the secondary electrons is detected using a PEEM. This allowed to image the shape and size of ceria nanoislands on Ru(0001) and to probe and compare the oxidation state

Synchrotron X-ray photoelectron spectroscopy study of sodium adsorption on vertically arranged MoS₂ layers coated with pyrolytic carbon

• Alexander V. Okotrub,
• Anastasiya D. Fedorenko,
• Anna A. Makarova,
• Veronica S. Sulyaeva,
• Yuliya V. Fedoseeva and
• Lyubov G. Bulusheva

Beilstein J. Nanotechnol. 2025, 16, 847–859, doi:10.3762/bjnano.16.64

• . The scanning electron microscopy (SEM) images of the surface of raw MoS2 film, hydrogen-annealed film, and PyC film are compared in Figure 1b,c,e. The raw MoS2 film covers the entire area of the substrate and contains polysulfide nanoparticles on the surface (Figure 1b). These nanoparticles are absent

Facile one-step radio frequency magnetron sputtering of Ni/NiO on stainless steel for an efficient electrode for hydrogen evolution reaction

• Ha Huu Do,
• Khac Binh Nguyen,
• Phuong N. Nguyen and
• Hoai Phuong Pham

Beilstein J. Nanotechnol. 2025, 16, 837–846, doi:10.3762/bjnano.16.63

• and metal oxide phases, offering a potential for HER. These outcomes indicated the successful Ni/NiO thin film fabrication on SS substrates. The uniformity of the electrocatalyst material is a vital factor that has a direct effect on electrode performance. Scanning electron microscopy (SEM) was

Synthesis and magnetic transitions of rare-earth-free Fe–Mn–Ni–Si-based compositionally complex alloys at bulk and nanoscale

• Shabbir Tahir,
• Tatiana Smoliarova,
• Carlos Doñate-Buendía,
• Michael Farle,
• Natalia Shkodich and
• Bilal Gökce

Beilstein J. Nanotechnol. 2025, 16, 823–836, doi:10.3762/bjnano.16.62

• 2.8 J·cm−2 [41]. Additionally, to increase the NP concentration and reduce the organic solvent use, a closed loop liquid flow system was employed. Size distribution, morphology, elemental composition, and crystal structure of the NPs from both CCA targets were examined using transmission electron

• microscopy (TEM) and EDX with a Jeol 2200FS microscope (Japan) equipped with an Oxford X-MaxN TLE 80 EDX detector (UK). The microscope was operated at an acceleration voltage of 200 kV and utilized a 2k × 2k GATAN UltraScan 1000XP CCD camera. For TEM analysis, the colloidal particles were dispersed onto a

Supramolecular hydration structure of graphene-based hydrogels: density functional theory, green chemistry and interface application

• Hon Nhien Le,
• Duy Khanh Nguyen,
• Minh Triet Dang,
• Huyen Trinh Nguyen,
• Thi Bang Tam Dao,
• Trung Do Nguyen,
• Chi Nhan Ha Thuc and
• Van Hieu Le

Beilstein J. Nanotechnol. 2025, 16, 806–822, doi:10.3762/bjnano.16.61

• GO-SG-ZH powder. The graphene-based nanocomposites in hydrogel form and in powder form were comparatively characterized using moisture analysis, scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), and aqueous dispersibility. Brush coating of graphene oxide–nanosilica–zinc

• coated with nanosilica. The nanosilica-coated films were denoted as SG/PLA. Materials characterization Materials weight and moisture values were measured using a laboratory balance (Ohaus Pioneer, 220 g/0.0001 g) and a moisture analyzer (A&D Weighing MX-50, 51 g/0.001 g), respectively. Scanning electron

• microscopy and energy-dispersive X-ray spectroscopy were performed using a JSM-IT200 system (JEOL). Samples were coated with Pt before the SEM-EDS analysis. X-ray diffraction was performed on a D8 Advance instrument (Bruker). Fourier-transform infrared spectroscopy (FTIR) was characterized with a FT/IR-6600

Morphology and properties of pyrite nanoparticles obtained by pulsed laser ablation in liquid and thin films for photodetection

• Akshana Parameswaran Sreekala,
• Bindu Krishnan,
• Rene Fabian Cienfuegos Pelaes,
• David Avellaneda Avellaneda,
• Josué Amílcar Aguilar-Martínez and
• Sadasivan Shaji

Beilstein J. Nanotechnol. 2025, 16, 785–805, doi:10.3762/bjnano.16.60

• microscopy, scanning electron microscopy, X-ray photoelectron spectroscopy, and ultraviolet–visible spectroscopy. The morphology of the NPs in different solvents varied from spherical, rice-like to rod-like particles which demonstrates the effect of the solvent on the morphology/composition of NPs

• nanocolloid in this work. The optical properties of nanocolloids and their thin films were evaluated using UV–visible (UV–vis) spectroscopy. The nanoparticle characterization and surface morphology were studied using transmission electron microscopy (TEM), scanning electron microscopy (SEM), and the

• temperatures and amounts of sulfur. Characterization The morphological analyses of pyrite NPs were recorded using the FEI Titan G2 80–300 for TEM, high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM), high-resolution TEM (HRTEM) and selected area electron diffraction (SAED). The

Changes of structural, magnetic and spectroscopic properties of microencapsulated iron sucrose nanoparticles in saline

• Sabina Lewińska,
• Pavlo Aleshkevych,
• Roman Minikayev,
• Anna Bajorek,
• Mateusz Dulski,
• Krystian Prusik,
• Tomasz Wojciechowski and
• Anna Ślawska-Waniewska

Beilstein J. Nanotechnol. 2025, 16, 762–784, doi:10.3762/bjnano.16.59

• changes upon dissolution in saline were tested. For the undissolved sample, calcium alginate microcapsules with irregular shapes were registered via scanning electron microscopy, inside which core–shell nanoparticles were identified by transmission electron microscopy micrographs. Magnetic studies (DC and

• information about the iron release process from such microcapsules based on changes in physical properties. In order to carry out this study, a multi-technique analysis of undissolved and dissolved compounds was performed, including microstructure studies using scanning electron microscopy (SEM) and

• transmission electron microscopy (TEM). Composition studies using XRD, magnetic properties using dc and ac magnetometry, and extensive spectral analysis using Fourier-transform infrared spectroscopy (FTIR), Raman, and electron paramagnetic resonance (EPR) were also performed. Considering that the AB-Fortis

Efficiency of single-pulse laser fragmentation of organic nutraceutical dispersions in a circular jet flow-through reactor

• Tina Friedenauer,
• Maximilian Spellauge,
• Alexander Sommereyns,
• Verena Labenski,
• Tuba Esatbeyoglu,
• Christoph Rehbock,
• Heinz P. Huber and
• Stephan Barcikowski

Beilstein J. Nanotechnol. 2025, 16, 711–727, doi:10.3762/bjnano.16.55

• yield of submicrometer particles and nanoparticles was quantified using UV–vis extinction spectroscopy, scanning electron microscopy, and analytical centrifugation, while high-performance liquid chromatography determined degradation. We found improved fragmentation efficiency at lower mass

High-temperature epitaxial growth of tantalum nitride thin films on MgO: structural evolution and potential for SQUID applications

• Michelle Cedillo Rosillo,
• Oscar Contreras López,
• Jesús Antonio Díaz,
• Agustín Conde Gallardo and
• Harvi A. Castillo Cuero

Beilstein J. Nanotechnol. 2025, 16, 690–699, doi:10.3762/bjnano.16.53

• , atomic force microscopy, and transmission electron microscopy analyses revealed that the TaN films exhibit excellent crystallinity and smooth surface morphology, when deposited at optimal temperatures of 750 and 850 °C. The films exhibit superconducting transition temperatures (Tc) ranging from 5.0 to

• 750 °C, the sample, which has δ-TaN as the significant phase, exhibits a superconducting transition at Tc = 5.3 K. The highest value of Tc was obtained for the film deposited at 850 °C with pN2 = 90 mTorr (Tc = 6.3 K). Cross-sectional transmission electron microscopy samples were prepared by a 4 kV Ar

The impact of tris(pentafluorophenyl)borane hole transport layer doping on interfacial charge extraction and recombination

• Konstantinos Bidinakis and
• Stefan A. L. Weber

Beilstein J. Nanotechnol. 2025, 16, 678–689, doi:10.3762/bjnano.16.52

• scanning electron microscopy (SEM) and atomic force microscopy (AFM) images (See Supporting Information File 1, Section 4). The lateral resolution for both AFM and SEM measurements is a few nanometers. The AFM channel that exhibited the clearest contrast between the layers was the amplitude error signal

Colloidal few layered graphene–tannic acid preserves the biocompatibility of periodontal ligament cells

• Teissir Ben Ammar,
• Naji Kharouf,
• Dominique Vautier,
• Housseinou Ba,
• Nivedita Sudheer,
• Philippe Lavalle and
• Vincent Ball

Beilstein J. Nanotechnol. 2025, 16, 664–677, doi:10.3762/bjnano.16.51

• granules, each being hundreds of micrometers in size (Figure 1A). In contrast, the obtained FLG–TA colloid has a layered structure, and sheets seem to have been peeled off from the graphite surface (Figure 1B,C). Transmission electron microscopy (TEM) micrographs of the flakes’ edges (Figure 1D,E) reveal

• with FLG–TA concentrations ranging from 1 to 200 µg·mL−1. Cellular morphology was examined using scanning electron microscopy (SEM, Figure 5), with untreated cells as controls. The occupancy index (OI) of FLG–TA in cell populations and the lateral dimensions of FLG–TA particles on cell membranes were

• the percentage reduction in ROS levels compared to the control group. Cell morphology To assess potential changes in cell morphology induced by FLG–TA, scanning electron microscopy (SEM) was performed on treated and untreated cells after 24 and 48 h of direct contact. Cells were cultured on 12 mm

Aprepitant-loaded solid lipid nanoparticles: a novel approach to enhance oral bioavailability

• Mazhar Hussain,
• Muhammad Farooq,
• Muhammad Asad Saeed,
• Muhammad Ijaz,
• Sherjeel Adnan,
• Zeeshan Masood,
• Muhammad Waqas,
• Wafa Ishaq and
• Nabeela Ameer

Beilstein J. Nanotechnol. 2025, 16, 652–663, doi:10.3762/bjnano.16.50

• solubility and enhanced dissolution using a minimum quantity of carriers. The developed SLNs were evaluated regarding drug content and using scanning electron microscopy (SEM), thermal gravimetric analysis (TGA) and differential scanning calorimetry (DSC), as well as polydispersity index (PDI), particle size

• . Scanning electron microscopy (SEM) photographs of APT-NPs were obtained on a JSM-6380A, Joel, Japan operating at a voltage of 10.0 kV. The specimens were mounted on a metallic stub with double-sided adhesive tape and gold-coated in an argon atmosphere prior to observation [28]. Drug excipient interaction

• analysis. APT-loaded SLNs were prepared by the precipitation method and characterized by physicochemical studies including particle size and zeta potential measurements, drug content, encapsulation efficiency and solubility studies, Fourier-transform infrared spectroscopy (FTIR), scanning electron

Feasibility analysis of carbon nanofiber synthesis and morphology control using a LPG premixed flame

• Iftikhar Rahman Bishal,
• Muhammad Hilmi Ibrahim,
• Norikhwan Hamzah,
• Mohd Zamri Mohd Yusop,
• Faizuan Bin Abdullah,
• I Putu Tedy Indrayana and
• Mohd Fairus Mohd Yasin

Beilstein J. Nanotechnol. 2025, 16, 581–590, doi:10.3762/bjnano.16.45

• placement of the thermocouple within the flame, a two-axis positioning system was employed with an Arduino-based control unit. The positioning system has 1 mm accuracy with x- and y-axis traverse ranges of 100 and 200 mm, respectively. The grown CNFs were characterized by field-emission scanning electron

• microscopy (FESEM, Zeiss Crossbeam 340) for morphological analysis. Raman spectroscopy (HORIBA XploRA PLUS, 532 nm) was carried out to analyze the signature spectra of the grown CNFs. Results and Discussion Flame characterization and temperature The flames were characterized regarding flame shape and

Retrieval of B1 phase from high-pressure B2 phase for CdO nanoparticles by electronic excitations in Cd_xZn_1−xO composite thin films

• Arkaprava Das,
• Marcin Zając and
• Carla Bittencourt

Beilstein J. Nanotechnol. 2025, 16, 551–560, doi:10.3762/bjnano.16.43

• spectrometer (Bruker), equipped with an Ar ion laser (532 nm) with 0.2 mW laser operating power. Scanning electron microscopy (SEM) analysis was carried out with a HITACHI SU8020 model, using an electron beam energy of 3.0 keV. X-ray photoelectron spectroscopy (XPS) was performed using an ESCA-5000 Versa Probe

Functionalized gold nanoflowers on carbon screen-printed electrodes: an electrochemical platform for biosensing hemagglutinin protein of influenza A H1N1 virus

• Carlos Enrique Torres-Méndez,
• Sharmilee Nandi,
• Klara Martinovic,
• Patrizia Kühne,
• Yifan Liu,
• Sam Taylor,
• Maria Lysandrou,
• Maria Ines Berrojo Romeyro Mascarenhas,
• Viktoria Langwallner,
• Javier Enrique Sebastián Alonso,
• Ivana Jovanovic,
• Maike Lüftner,
• Georgia-Vasiliki Gkountana,
• David Bern,
• Abdul-Raouf Atif,
• Ehsan Manouchehri Doulabi,
• Gemma Mestres and
• Masood Kamali-Moghaddam

Beilstein J. Nanotechnol. 2025, 16, 540–550, doi:10.3762/bjnano.16.42

• protein at clinically relevant concentrations. Scanning electron microscopy Scanning electron microscopy (SEM) analysis was explored to characterize the surface of the electrodes after electrodeposition of gold nanoparticles (Figure 2). Because of the high conductivity of gold, a difference in contrast is

Electron beam-based direct writing of nanostructures using a palladium β-ketoesterate complex

• Chinmai Sai Jureddy,
• Krzysztof Maćkosz,
• Aleksandra Butrymowicz-Kubiak,
• Iwona B. Szymańska,
• Patrik Hoffmann and
• Ivo Utke

Beilstein J. Nanotechnol. 2025, 16, 530–539, doi:10.3762/bjnano.16.41

• oxygen signal of the native oxide layer is separated from the signal of oxygen from ligand residues of [Pd(tbaoac)2] in the deposit. Nanostructural observations were performed with transmission electron microscopy (TEM) using a probe-corrected ThermoFisher Scientific Titan Themis 200 G3 operating at an

Zeolite materials with Ni and Co: synthesis and catalytic potential in the selective hydrogenation of citral

• Inocente Rodríguez-Iznaga,
• Yailen Costa Marrero,
• Tania Farias Piñeira,
• Céline Fontaine,
• Lexane Paget,
• Beatriz Concepción Rosabal,
• Arbelio Penton Madrigal,
• Vitalii Petranovskii and
• Gwendoline Lafaye

Beilstein J. Nanotechnol. 2025, 16, 520–529, doi:10.3762/bjnano.16.40

• nitrogen adsorption at 77 K. The initial natural zeolite samples were also examined via powder X-ray diffraction (XRD) and scanning electron microscopy (SEM). XRD patterns were recorded using a PW 1218 diffractometer (Philips, Almelo, Netherlands) equipped with a curved graphite monochromator and Cu Kα

Performance optimization of a microwave-coupled plasma-based ultralow-energy ECR ion source for silicon nanostructuring

• Joy Mukherjee,
• Safiul Alam Mollick,
• Tanmoy Basu and
• Tapobrata Som

Beilstein J. Nanotechnol. 2025, 16, 484–494, doi:10.3762/bjnano.16.37

• formation of well-defined nanoscale ripple patterns. The prominence of ripple structures increases with prolonged irradiation time, while bombardment at 72.5° with the same ion beam parameters leads to the coarsening of nanostructures. Cross-sectional transmission electron microscopy (TEM) measurements

Effect of additives on the synthesis efficiency of nanoparticles by laser-induced reduction

• Rikuto Kuroda,
• Takahiro Nakamura,
• Hideki Ina and
• Shuhei Shibata

Beilstein J. Nanotechnol. 2025, 16, 464–472, doi:10.3762/bjnano.16.35

• solution without IPA. On the other hand, when 10 vol % IPA was added (red line in Figure 1), an increase in absorbance was immediately seen after the start of laser irradiation, and the absorbance levelled off after 5 min of laser irradiation. Figure 2 shows the transmission electron microscopy (TEM

• alloy nanoparticles by LRL with the addition of IPA as a radical scavenger to a solution containing multiple metal ions, and the structure of the synthesized nanoparticles was evaluated by scanning transmission electron microscopy-energy dispersive spectroscopy (STEM-EDS). In this case, we selected an

Quantification of lead through rod-shaped silver-doped zinc oxide nanoparticles using an electrochemical approach

• Ravinder Lamba,
• Gaurav Bhanjana,
• Neeraj Dilbaghi,
• Vivek Gupta and
• Sandeep Kumar

Beilstein J. Nanotechnol. 2025, 16, 422–434, doi:10.3762/bjnano.16.33

• Scherrer method. This difference is proportional to the strain value [17]. Field-emission scanning electron microscopy of Ag@ZnO nanorods The general morphological characteristics of the as-obtained nanorods were analyzed by electron microscopy. Figure 2a depicts the typical field-emission scanning

• electron microscopy (FESEM) image of the as-obtained nanomaterials. The produced nanomaterials had rod-shaped morphologies and were grown at extremely high densities, as seen by the SEM image. Figure 2b represents the average diameter of Ag@ZnO NRs which was calculated using the Image J software. The

Size control of nanoparticles synthesized by pulsed laser ablation in liquids using donut-shaped beams

• Abdel Rahman Altakroury,
• Oleksandr Gatsa,
• Farbod Riahi,
• Zongwen Fu,
• Miroslava Flimelová,
• Andrei Samokhvalov,
• Stephan Barcikowski,
• Carlos Doñate-Buendía,
• Alexander V. Bulgakov and
• Bilal Gökce

Beilstein J. Nanotechnol. 2025, 16, 407–417, doi:10.3762/bjnano.16.31

• the morphology and size of the NPs synthesized by PLAL, the colloidal samples were drop-cast on a silicon wafer and dried for microscopic analysis. All NPs were characterized using scanning electron microscopy (SEM, Quanta 400 FEG, FEI Company, USA and TESCAN MIRA3 LMH, Brno, Czech Republic). The

ReactorAFM/STM – dynamic reactions on surfaces at elevated temperature and atmospheric pressure

• Tycho Roorda,
• Hamed Achour,
• Matthijs A. van Spronsen,
• Marta E. Cañas-Ventura,
• Sander B. Roobol,
• Willem Onderwaater,
• Mirthe Bergman,
• Peter van der Tuijn,
• Gertjan van Baarle,
• Johan W. Bakker,
• Joost W. M. Frenken and
• Irene M. N. Groot

Beilstein J. Nanotechnol. 2025, 16, 397–406, doi:10.3762/bjnano.16.30

• connected through a 3-contact slider for AFM drive, AFM readout, and STM readout. (b) Scanning electron microscopy image of a 25 μm wide chemically etched Pt/Ir wire tip. qPlus resonance frequency (black dots) as a function of the temperature ranging from room temperature to 500 K. The red curve is a fit