Electrospun polysuccinimide scaffolds containing different salts as potential wound dressing material

• Veronika Pálos,
• Krisztina S. Nagy,
• Rita Pázmány,
• Krisztina Juriga-Tóth,
• Bálint Budavári,
• Judit Domokos,
• Dóra Szabó,
• Ákos Zsembery and
• Angela Jedlovszky-Hajdu

Beilstein J. Nanotechnol. 2024, 15, 781–796, doi:10.3762/bjnano.15.65

• polymer-based systems (<500 nm). Fourier-transform infrared spectroscopy was applied to verify the presence of salts in the scaffolds and to determine the interaction between the salt and the polymer. Another analysis, energy-dispersive X-ray spectroscopy, was carried out to determine strontium and zinc

• scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), mechanical tests, investigation of salt dissolution from the scaffolds, examination of their antibacterial activity against four different bacterial strains (Escherichia coli, Pseudomonas aeruginosa, Bacillus subtilis, and

• , which was placed on a slow rotary drum (10 rpm). The distance between the needle of the syringe and the collector was 15 cm in all cases. The applied voltages (direct current power supply, ES 30 Model, Gamma High Voltage Inc., USA) and flow rates are in Table 1. Fourier-transform infrared spectroscopy

Exploring surface charge dynamics: implications for AFM height measurements in 2D materials

• Mario Navarro-Rodriguez,
• Andres M. Somoza and
• Elisa Palacios-Lidon

Beilstein J. Nanotechnol. 2024, 15, 767–780, doi:10.3762/bjnano.15.64

• , t) into the Fourier transform of Equation 2. From V(k, z, t), it is possible to calculate the Joule dissipation. In particular, for our case (σ1, σ2 = 0), the dissipated power, P, takes the simple expression: Because of the linearity of Equation 2, the oscillating part of the total electrostatic

Green synthesis of biomass-derived carbon quantum dots for photocatalytic degradation of methylene blue

• Dalia Chávez-García,
• Mario Guzman,
• Viridiana Sanchez and
• Rubén D. Cadena-Nava

Beilstein J. Nanotechnol. 2024, 15, 755–766, doi:10.3762/bjnano.15.63

• 24 h, CQDs were successfully synthesized. A comprehensive characterization of the CQDs was performed using UV–visible spectroscopy, Fourier-transform infrared spectroscopy, dynamic light scattering, Raman spectroscopy, and luminescence spectroscopy, confirming their high quality. The photocatalytic

• catalytic activity in MB degradation, while those prepared with water as a solvent did not show significant catalytic activity. The samples were also characterized using UV–visible spectra, Fourier-transform infrared spectroscopy (FTIR), Raman spectroscopy, dynamic light scattering (DLS), and

• length quartz cell was used for the measurements, and deionized water was used as the blank in the measurement to account for background signals. Fourier-transform infrared spectra were measured on a Spectrum Two FT-IR/Sp 10 S/W spectrometer (USA) with a LiTaO3 type detector, the wavelength used ranged

Gold nanomakura: nanoarchitectonics and their photothermal response in association with carrageenan hydrogels

• Nabojit Das,
• Vikas,
• Akash Kumar,
• Sanjeev Soni and
• Raja Gopal Rayavarapu

Beilstein J. Nanotechnol. 2024, 15, 678–693, doi:10.3762/bjnano.15.56

• , respectively. The observed trend in decreasing aspect ratio is CTAB-AuNM > MTAB-AuNM > DTAB-AuNM. Fourier-transform infrared spectroscopy and X-ray diffraction analysis The CTAB-, MTAB-, and DTAB-capped gold nanoparticles exhibited strong peaks at 2848 and 2915 cm−1 due to symmetric and asymmetric C–H

Exfoliation of titanium nitride using a non-thermal plasma process

• Priscila Jussiane Zambiazi,
• Dolores Ribeiro Ricci Lazar,
• Larissa Otubo,
• Rodrigo Fernando Brambilla de Souza,
• Almir Oliveira Neto and
• Cecilia Chaves Guedes-Silva

Beilstein J. Nanotechnol. 2024, 15, 631–637, doi:10.3762/bjnano.15.53

• detailed view of the materials structure, revealing that it retained some crystallinity, typical of 2D nanofilms. This retention of crystalline structure was further confirmed by fast Fourier transform (FFT) analysis. Notably, the d-spacing of the (200) crystal plane increased from 2.08 to 3.09 Å (as

Stiffness calibration of qPlus sensors at low temperature through thermal noise measurements

• Laurent Nony,
• Sylvain Clair,
• Daniel Uehli,
• Aitziber Herrero,
• Jean-Marc Themlin,
• Andrea Campos,
• Franck Para,
• Alessandro Pioda and
• Christian Loppacher

Beilstein J. Nanotechnol. 2024, 15, 580–602, doi:10.3762/bjnano.15.50

• integration of a quantity we name the thermal noise PSD (tn-PSD) (f), according to: Technically, the PSD is defined from the Fourier transform (f) of the time trace of the signal z(t) forming the Fourier pair z(t) (f), according to: Thus, if the measurement noise PSD (f) is quantified, the quantity

• depicting the thermal fluctuations of the probe can be estimated from the measurement of Sz(f) (Equation 15) and, thus, also the probe stiffness (Equation 7). Because the Fourier transform is intrinsically two-sided (f ∈ ℝ), the integration in Equation 12, Equation 13, and Equation 15 spreads from −∞ to

• ). It is therefore preferable to express their corresponding PSD from the rms value of their Fourier transform. Supporting Information File 2 explicitly details the connection between the two-sided expression of the PSD and that of the one-sided rms PSD (cf. Supporting Information File 2, Equations S14

Radiofrequency enhances drug release from responsive nanoflowers for hepatocellular carcinoma therapy

• Yanyan Wen,
• Ningning Song,
• Yueyou Peng,
• Weiwei Wu,
• Qixiong Lin,
• Minjie Cui,
• Rongrong Li,
• Qiufeng Yu,
• Sixue Wu,
• Yongkang Liang,
• Wei Tian and
• Yanfeng Meng

Beilstein J. Nanotechnol. 2024, 15, 569–579, doi:10.3762/bjnano.15.49

• hydrated state [31]. The DLS depicted size is the closest to that in vivo. The Fourier-transform infrared (FTIR) spectrum of CUR exhibited vibrational absorption peaks at 1207 cm−1 and 3330 cm−1 corresponding to C=O and –OH, respectively, in the phenolic hydroxy group (Figure 2f). Similarly, for bis(4

• measured by a Malvern Zetasizer Nano ZS instrument (Nano ZS90, Malvern, UK). A 2 mg NF sample was added into 1 mL of deionized water and directly detected by ZS90. The detection angle was 90 degrees. The compositions were also analyzed using Fourier-transform infrared spectroscopy (Nicolet iS50, Thermo

Photocatalytic degradation of methylene blue under visible light by cobalt ferrite nanoparticles/graphene quantum dots

• Vo Chau Ngoc Anh,
• Le Thi Thanh Nhi,
• Le Thi Kim Dung,
• Dang Thi Ngoc Hoa,
• Nguyen Truong Son,
• Nguyen Thi Thao Uyen,
• Nguyen Ngoc Uyen Thu,
• Le Van Thanh Son,
• Le Trung Hieu,
• Tran Ngoc Tuyen and
• Dinh Quang Khieu

Beilstein J. Nanotechnol. 2024, 15, 475–489, doi:10.3762/bjnano.15.43

• electron microscopy, transmission electron microscopy, ultraviolet–visible diffuse reflectance spectroscopy, Fourier-transform infrared spectroscopy, photoluminescence spectroscopy, vibrating-sample magnetometry, and nitrogen adsorption/desorption isotherms. Cobalt ferrite crystals of around 8–10 nm and

• benzoquinone (C6H4O2) was provided by Sigma-Aldrich, USA. Sodium hydroxide (NaOH, ≥96%) and hydrogen chloride (HCl, 38%) were purchased from Xilong, China. Instruments X-ray diffraction (XRD) patterns were recorded by using a D8 Advance (Bruker, Germany) with Cu Kα radiation (λ = 0.154 nm). Fourier-transform

Vinorelbine-loaded multifunctional magnetic nanoparticles as anticancer drug delivery systems: synthesis, characterization, and in vitro release study

• Zeynep Özcan and
• Afife Binnaz Hazar Yoruç

Beilstein J. Nanotechnol. 2024, 15, 256–269, doi:10.3762/bjnano.15.24

• Pro) using Cu Kα radiation (λ = 0.15418 nm) in a 2θ range of 10° to 90°. Fourier-transform infrared (FTIR, Thermo, Nicolet Is 10) spectra of the nanostructures were obtained in the range of 4000–400 cm−1. The amounts of released drug were obtained using a UV–vis spectrophotometer (Shimadzu Scientific

Nanocarrier systems loaded with IR780, iron oxide nanoparticles and chlorambucil for cancer theragnostics

• Phuong-Thao Dang-Luong,
• Hong-Phuc Nguyen,
• Loc Le-Tuan,
• Xuan-Thang Cao,
• Vy Tran-Anh and
• Hieu Vu Quang

Beilstein J. Nanotechnol. 2024, 15, 180–189, doi:10.3762/bjnano.15.17

• oleic acid was added to the solution and heated to 70 °C for 30 min. The synthesized IO NPs were washed three times with 50 mL of DCM and stored at −80 °C for further experiments. Synthesis of folate-F127 The synthesis was done as previously described [13]. The Fourier-transform infrared spectroscopy

Modification of graphene oxide and its effect on properties of natural rubber/graphene oxide nanocomposites

• Nghiem Thi Thuong,
• Le Dinh Quang,
• Vu Quoc Cuong,
• Cao Hong Ha,
• Nguyen Ba Lam and
• Seiichi Kawahara

Beilstein J. Nanotechnol. 2024, 15, 168–179, doi:10.3762/bjnano.15.16

• characterized by X-ray diffraction (XRD), Fourier-transform infrared spectroscopy, contact angle, thermal gravimetric analysis, and scanning electron microscopy. The XRD results showed the appearance of an amorphous region of silica particles at a diffraction angle of 22°. The formation of silica was

• conditions to determine the ideal condition to modify GO for grafting onto NR. The GO-VTES products were characterized using X-ray diffraction (XRD), contact angle, 29Si NMR, Fourier-transform infrared spectroscopy (FTIR), and morphology analysis. The GO-VTES was expected to improve the mechanical properties

• -VTES(a). Attenuated total reflection–Fourier-transform infrared spectroscopy results The attenuated total reflection–Fourier-transform infrared spectroscopy (ATR–FTIR) results of GO, GO-VTES(a), and GO-VTES(b) are shown in Figure 5. The absorption values ranging from 3100 to 3700 cm−1 corresponded to

In situ optical sub-wavelength thickness control of porous anodic aluminum oxide

• Aleksandrs Dutovs,
• Raimonds Popļausks,
• Oskars Putāns,
• Vladislavs Perkanuks,
• Aušrinė Jurkevičiūtė,
• Tomas Tamulevičius,
• Uldis Malinovskis,
• Iryna Olyshevets,
• Donats Erts and
• Juris Prikulis

Beilstein J. Nanotechnol. 2024, 15, 126–133, doi:10.3762/bjnano.15.12

• ) setup, the PAAO structure was analyzed using the fast Fourier transform (FFT) method [21]. However, the optimal PAAO thickness for FFT analysis was ≈2.5–5.0 μm, where multiple interference fringes can be observed in the reflectance spectra. Here, the PAAO thickness was calculated in real time by fitting

Assessing phytotoxicity and tolerance levels of ZnO nanoparticles on Raphanus sativus: implications for widespread adoptions

• Pathirannahalage Sahan Samuditha,
• Nadeesh Madusanka Adassooriya and
• Nazeera Salim

Beilstein J. Nanotechnol. 2024, 15, 115–125, doi:10.3762/bjnano.15.11

• on Raphanus sativus (R. sativus) concerning its tolerance levels, toxicity, and accumulation. ZnO NPs were synthesized by the wet chemical method and characterized by powder X-ray diffraction (PXRD), Fourier-transform infrared (FTIR) spectroscopy, ultraviolet–visible (UV–vis) spectroscopy, dynamic

• synthesized ZnO NPs were characterized via several techniques such as powder X-ray diffraction (PXRD), Fourier-transform infrared (FTIR) spectroscopy, solid-UV–vis spectroscopy, dynamic light scattering (DLS), and scanning electron microscopy (SEM). Then the potential phytotoxicity of the synthesized ZnO NPs

Berberine-loaded polylactic acid nanofiber scaffold as a drug delivery system: The relationship between chemical characteristics, drug-release behavior, and antibacterial efficiency

• Le Thi Le,
• Hue Thi Nguyen,
• Liem Thanh Nguyen,
• Huy Quang Tran and
• Thuy Thi Thu Nguyen

Beilstein J. Nanotechnol. 2024, 15, 71–82, doi:10.3762/bjnano.15.7

• bonds, Fourier transform infrared spectroscopy (FTIR) was used to examine the differences in chemical characteristics of BBR-loaded PLA nanofiber scaffolds (Figure 2A). The FTIR spectrum of PLA nanofiber scaffold shows the adsorption peaks at 1751 cm−1 resulting from the stretching vibrations of the C=O

• ImageJ software as an image analysis tool. Fourier-transform infrared spectroscopy was performed in a Nicolet NEXUS 670 spectrometer. The resulting spectra were recorded in transmission mode in the wavelength range of 500–4000 cm−1. A Raman spectrometer (MacroRAM, Horiba) was used to investigate the

Influence of conductive carbon and MnCo₂O₄ on morphological and electrical properties of hydrogels for electrochemical energy conversion

• Sylwia Pawłowska,
• Karolina Cysewska,
• Yasamin Ziai,
• Jakub Karczewski,
• Piotr Jasiński and
• Sebastian Molin

Beilstein J. Nanotechnol. 2024, 15, 57–70, doi:10.3762/bjnano.15.6

• MCO and cCB particles in the hydrogel precursor solution to obtain a more homogeneous distribution of these particles in the structure of the polymer matrix and on its surface. The Fourier-transform infrared spectroscopy (FTIR) results of the hydrogel compositions and their pure components are shown

TEM sample preparation of lithographically patterned permalloy nanostructures on silicon nitride membranes

• Joshua Williams,
• Michael I. Faley,
• Joseph Vimal Vas,
• Peng-Han Lu and
• Rafal E. Dunin-Borkowski

Beilstein J. Nanotechnol. 2024, 15, 1–12, doi:10.3762/bjnano.15.1

• reciprocal space vector related to the tilt of the reference wave. Note that the phase φi(r) is now separated in the third term inside the cosine; it can be retrieved by taking the fast Fourier transform (FFT) of the intensity [24]. The phase shift can then be used to recover the in-plane magnetic

unDrift: A versatile software for fast offline SPM image drift correction

• Tobias Dickbreder,
• Franziska Sabath,
• Lukas Höltkemeier,
• Ralf Bechstein and
• Angelika Kühnle

Beilstein J. Nanotechnol. 2023, 14, 1225–1237, doi:10.3762/bjnano.14.101

• lattice parameters are shown as a lattice drawn with red lines. For the Fourier transform, this fit yields lattice vectors of the inverse lattice, which are then transformed into real-space lattice vectors. For the autocorrelation, the optimization yields the real-space lattice vectors directly. To finish

• to choose whether the algorithm operates based on Fourier transform or autocorrelation. This choice mostly depends on the size of the image relative to the size of the observed periodic structure. For images showing many unit cells, we find that the Fourier transform yields better results, while the

• measured SPM images. For images containing many unit cells, each unit cell only consists of few pixels; thus, the maxima in the autocorrelation are difficult to separate, as they also consist of few pixels. The Fourier transform, in contrast, works in the inverse space, which is why the maxima are very

Curcumin-loaded albumin submicron particles with potential as a cancer therapy: an in vitro study

• Nittiya Suwannasom,
• Netsai Sriaksorn,
• Chutamas Thepmalee,
• Krissana Khoothiam,
• Ausanai Prapan,
• Hans Bäumler and
• Chonthida Thephinlap

Beilstein J. Nanotechnol. 2023, 14, 1127–1140, doi:10.3762/bjnano.14.93

• . SEM images were obtained under high-vacuum conditions at an operation voltage of 15 kV. Fourier-transform infrared spectroscopy Chemical characteristics of CUR, HSA, HSA-MPs, and CUR-HSA-MPs were examined using Fourier-transform infrared spectroscopy (FTIR, Thermo Scientific, NICOLET IS5, Waltham, MA

Dual-heterodyne Kelvin probe force microscopy

• Benjamin Grévin,
• Fatima Husainy,
• Dmitry Aldakov and
• Cyril Aumaître

Beilstein J. Nanotechnol. 2023, 14, 1068–1084, doi:10.3762/bjnano.14.88

• referred to as the amplitude (modulus) spectrum in the following. Obviously, by linearity of the Fourier transform, each component of the “amplitude spectrum” (including the static term) is proportional to the amplitude (or magnitude) of the SPV. We will see later on how static (SPV magnitude) and dynamic

• Fourier transform in the case of a signal demodulation based on the n_4 sidebands. At the exception of the harmonics directly neighbouring the null component (n = 10 in the case of a 10% duty ratio pump waveform), the measured phase values match fairly well the ones expected from the pump Fourier

• DHe-KPFM to probe the Fourier spectrum of the time-periodic electrostatic surface potential. The pumps consisted of a square wave with a 50% duty ratio (Figure 2a) and a saw-tooth (Figure 2b). In either case, the amplitude and phase spectra almost perfectly match those expected from a simple Fourier

Upscaling the urea method synthesis of CoAl layered double hydroxides

• Camilo Jaramillo-Hernández,
• Víctor Oestreicher,
• Martín Mizrahi and
• Gonzalo Abellán

Beilstein J. Nanotechnol. 2023, 14, 927–938, doi:10.3762/bjnano.14.76

• and Figure S2, Supporting Information File 1). Table S1 summarizes the values of dBS and parameter a for all samples. Attenuated total reflectance Fourier-transform infrared spectroscopy (ATR-FTIR) provides valuable information about the nature of the layered hydroxide structure and the intercalated

• total reflectance Fourier-transform infrared spectroscopy (ATR-FTIR) spectra were collected on a Bruker alpha II FTIR spectrometer in the 4000–400 cm−1 range. X-ray photoelectron spectroscopy (XPS) measurements were recorded on a Thermo Scientific™ K-alpha X-ray photoelectron spectrometer. Al Kα

A wearable nanoscale heart sound sensor based on P(VDF-TrFE)/ZnO/GR and its application in cardiac disease detection

• Yi Luo,
• Jian Liu,
• Jiachang Zhang,
• Yu Xiao,
• Ying Wu and
• Zhidong Zhao

Beilstein J. Nanotechnol. 2023, 14, 819–833, doi:10.3762/bjnano.14.67

• generally associated with better piezoelectric performance of the material. To further validate the enhancement of the β phase, Fourier-transform infrared (FTIR) analysis was conducted (Figure 7a). The FTIR spectrum of the piezoelectric film exhibited distinct absorption bands. Peaks observed at 600, 763

Nanostructured lipid carriers containing benznidazole: physicochemical, biopharmaceutical and cellular in vitro studies

• Giuliana Muraca,
• María Esperanza Ruiz,
• Rocío C. Gambaro,
• Sebastián Scioli-Montoto,
• María Laura Sbaraglini,
• Gisel Padula,
• José Sebastián Cisneros,
• Cecilia Yamil Chain,
• Vera A. Álvarez,
• Cristián Huck-Iriart,
• Guillermo R. Castro,
• María Belén Piñero,
• Matias Ildebrando Marchetto,
• Catalina Alba Soto,
• Germán A. Islan and
• Alan Talevi

Beilstein J. Nanotechnol. 2023, 14, 804–818, doi:10.3762/bjnano.14.66

• observed by transmission electron microscopy. Fourier-transform infrared spectroscopy, differential scanning calorimetry, thermogravimetric analysis, and small-angle X-ray scattering analyses of the nanoparticles indicated that BNZ might be dispersed in the nanoparticle matrix in an amorphous state. The

• 410 °C, and BNZ degradation occurred in the 190–300 °C range. Considering these processes, nanoparticle thermal behavior might be attributed first to lipid degradation, and second to poloxamer weight loss. The attenuated total reflection Fourier-transform infrared spectroscopy (ATR-FTIR) technique was

• Fourier-transform infrared spectroscopy Fourier-transform infrared spectroscopy spectra were obtained. The attenuated total reflection mode was used to record the spectra over the range of 400–4000 cm−1 at a resolution of 2 cm−1. Transmission electron microscopy Transmission electron microscopy images

Silver nanoparticles loaded on lactose/alginate: in situ synthesis, catalytic degradation, and pH-dependent antibacterial activity

• Nguyen Thi Thanh Tu,
• T. Lan-Anh Vo,
• T. Thu-Trang Ho,
• Kim-Phuong T. Dang,
• Van-Dung Le,
• Phan Nhat Minh,
• Chi-Hien Dang,
• Vinh-Thien Tran,
• Van-Su Dang,
• Tran Thi Kim Chi,
• Hieu Vu-Quang,
• Radek Fajgar,
• Thi-Lan-Huong Nguyen,
• Van-Dat Doan and
• Thanh-Danh Nguyen

Beilstein J. Nanotechnol. 2023, 14, 781–792, doi:10.3762/bjnano.14.64

• potential measurements, which were measured on a nanoPartica Horiba SZ-100 (Japan). Fourier-transform infrared (FTIR) spectra were obtained using a Bruker Tensor 27 FTIR spectrophotometer (Germany). X-ray diffraction (XRD) patterns were collected using a Bruker D8 Advance X-ray diffractometer. The

Quercetin- and caffeic acid-functionalized chitosan-capped colloidal silver nanoparticles: one-pot synthesis, characterization, and anticancer and antibacterial activities

• Akif Hakan Kurt,
• Elif Berna Olutas,
• Fatma Avcioglu,
• Hamza Karakuş,
• Mehmet Ali Sungur,
• Cansu Kara Oztabag and
• Muhammet Yıldırım

Beilstein J. Nanotechnol. 2023, 14, 362–376, doi:10.3762/bjnano.14.31

• characterization of quercetin- and caffeic acid-functionalized chitosan-capped colloidal silver nanoparticles (Ch/Q- and Ch/CA-Ag NPs), and their antibacterial and anticancer activities. The formation of Ch/Q- and Ch/CA-Ag NPs has been confirmed by ultraviolet–visible (UV–vis) spectroscopy, Fourier-transform

• nanoparticles The absorption spectra of quercetin, caffeic acid, chitosan, Ch-, Ch/Q-, and Ch/CA-Ag NPs were recorded on a UV–vis double-beam spectrophotometer (Hitachi U-2900) at wavelengths of 200 to 800 nm at 1.0 nm intervals with a quartz cell of 1.0 cm light path. Fourier-transform infrared (FTIR) spectra

Biocatalytic synthesis and ordered self-assembly of silica nanoparticles via a silica-binding peptide

• Mustafa Gungormus

Beilstein J. Nanotechnol. 2023, 14, 280–290, doi:10.3762/bjnano.14.25

• refractive indices. These structures are referred to as photonic crystals and can be manufactured synthetically for various optical applications. Similar optical behavior of the opal-like structures formed in this study will be demonstrated and discussed below. The fast Fourier transform of the SEM images

• , asterisk: clusters of approx. 10 nm particles). SEM micrographs of (a, c) single-layer and (b, d) multilayer self-assembled SiO2 particles (insets: corresponding fast Fourier transform diffraction pattern of the images). (e) UV–vis spectrogram of the self-assembled particles on a quartz surface. (f) Zeta