An efficient electrode material for high performance solid-state hybrid supercapacitors based on a Cu/CuO/porous carbon nanofiber/TiO₂ hybrid composite

• Mamta Sham Lal,
• Thirugnanam Lavanya and
• Sundara Ramaprabhu

Beilstein J. Nanotechnol. 2019, 10, 781–793, doi:10.3762/bjnano.10.78

• carbon nanofiber/TiO2 (Cu/CuO/PCNF/TiO2) composite uniformly covered with TiO2 nanoparticles was synthesized by electrospinning and a simple hydrothermal technique. The synthesized composite exhibits a unique morphology and excellent supercapacitive performance, including both electric double layer and

• nanoparticles, which together open up new opportunities for energy storage and conversion applications. Keywords: composite; electrochemical performance; porous carbon nanofiber; solid-state hybrid supercapacitor; supercapacitor; TiO2 nanoparticles; Introduction To meet the rapidly growing demand for energy

• capacitance due to degradation of the electrode material, and thus poor electrochemical stability [16][17][18]. TiO2 nanoparticles loaded onto the carbon materials is a reasonable solution to overcome this challenge and is a potential electrode material for energy storage applications, ascribing to its low

On the transformation of “zincone”-like into porous ZnO thin films from sub-saturated plasma enhanced atomic layer deposition

• Alberto Perrotta,
• Julian Pilz,
• Stefan Pachmajer,
• Antonella Milella and
• Anna Maria Coclite

Beilstein J. Nanotechnol. 2019, 10, 746–759, doi:10.3762/bjnano.10.74

• ZnO [15][16]. Liang et al. [15] reported on the transformation of zincones deposited on TiO2 nanoparticles into porous ZnO via thermal treatment in the presence of air. Low surface area and wide pore size distribution (in the micropore and mesopore size range) were achieved. The surface area and the

Gold nanoparticles embedded in a polymer as a 3D-printable dichroic nanocomposite material

• Lars Kool,
• Anton Bunschoten,
• Aldrik H. Velders and
• Vittorio Saggiomo

Beilstein J. Nanotechnol. 2019, 10, 442–447, doi:10.3762/bjnano.10.43

• modifying 3D-printable plastics with, for example, catalysts [11] or TiO2 nanoparticles [12] to obtain new improved materials with special characteristics. In this paper, we show how to fabricate a 3D-printable dichroic material using gold nanoparticles, jumping from the 4th century Roman glassmiths

Advanced scanning probe lithography using anatase-to-rutile transition to create localized TiO₂ nanorods

• Julian Kalb,
• Vanessa Knittel and
• Lukas Schmidt-Mende

Beilstein J. Nanotechnol. 2019, 10, 412–418, doi:10.3762/bjnano.10.40

• probe lithography method in which a silicon tip, commonly used for atomic force microscopy, was pulled across an anatase TiO2 film. This process scratches the film causing tiny anatase TiO2 nanoparticles to form on the surface. According to previous reports, these anatase particles convert into rutile

• atomic force microscope (AFM), was pulled across an anatase film. During this process, surface defects are created as well as dust that contains tiny anatase TiO2 nanoparticles. Due to the lattice mismatch between anatase and rutile, in general, rutile nanorods do not grow on anatase crystal facets. The

Threshold voltage decrease in a thermotropic nematic liquid crystal doped with graphene oxide flakes

• Mateusz Mrukiewicz,
• Krystian Kowiorski,
• Paweł Perkowski,
• Rafał Mazur and
• Małgorzata Djas

Beilstein J. Nanotechnol. 2019, 10, 71–78, doi:10.3762/bjnano.10.7

• nanoparticles of MgO and SiO2 [6]. Here, the effect was caused by the reduction of the order parameter S. The concentration-dependent enhancement of the electro-optic response was observed for Ti and TiO2 nanoparticles dispersed in NLC [7][8]. The significant effect of ferroelectric Sn2P2S6 on the threshold

Graphene-enhanced metal oxide gas sensors at room temperature: a review

• Dongjin Sun,
• Yifan Luo,
• Marc Debliquy and
• Chao Zhang

Beilstein J. Nanotechnol. 2018, 9, 2832–2844, doi:10.3762/bjnano.9.264

• this type of composite sensors is a problem. Recently Li et al. [73] reported an ultrafast and sensitive NH3 sensor using rGO decorated with TiO2 nanocrystals. There were two different morphologies in these sensing materials: rGO either laid on the surface of TiO2 nanoparticles, partly wrapping them

• , or made “bridges” at the interface between two nanoparticles. Due to the “bridges” existing between TiO2 nanoparticles, the initial resistance of TiO2–rGO sensor was greatly reduced, indicating that the sensor was able to work at room temperature. The partly “wrapping” microstructure enhanced the

• number of adsorption sites. Moreover, the TiO2–rGO sensor showed a better selectivity to NH3 than the pure rGO sensor owing to the acidic surface of TiO2 preferentially adsorbing primarily NH3. Ye et al. [74] stated that a TiO2–rGO sensor, fabricated via depositing GO and TiO2 nanoparticles on IDEs and

Nanocellulose: Recent advances and its prospects in environmental remediation

• Katrina Pui Yee Shak,
• Yean Ling Pang and
• Shee Keat Mah

Beilstein J. Nanotechnol. 2018, 9, 2479–2498, doi:10.3762/bjnano.9.232

• can facilitate the adsorption of metal oxide to its surface. Thus, Li et al. [123] proposed the immobilization of TiO2 nanoparticles on a fine fibrous network of bacterial cellulose via hydrogen bonds and electrostatic adsorption effect for the photocatalytic degradation of reactive X-3B. TiO2

• nanocomposites for photocatalytic hydrogen generation. The as-prepared nanocomposites generated 2–5 more hydrogen molecules in comparison with the control TiO2 nanoparticles. However, they found that the nanocomposites tend to photodegrade during photocatalytic reaction, and hence some of the nanocomposite

• nanoparticles and cellulose chains are compatible due to covalent bonds, which can improve the rigidity of the polymer chain and increase the energy required to break down the polymer chain [121]. Similar enhancement results were also obtained with cadmium sulphide (CdS) nanocrystals deposited on NCC which was

Electrospun one-dimensional nanostructures: a new horizon for gas sensing materials

• Muhammad Imran,
• Nunzio Motta and
• Mahnaz Shafiei

Beilstein J. Nanotechnol. 2018, 9, 2128–2170, doi:10.3762/bjnano.9.202

Sheet-on-belt branched TiO₂(B)/rGO powders with enhanced photocatalytic activity

• Huan Xing,
• Wei Wen and
• Jin-Ming Wu

Beilstein J. Nanotechnol. 2018, 9, 1550–1557, doi:10.3762/bjnano.9.146

• ' method according to our previous report [31]. To synthesize the TiO2(B)/rGO nanobelt (designated as TGN), 3 mL of GO suspension with a concentration of 2 mg/mL was added to 30 mL of 10 M NaOH aqueous solution, together with 0.2 g commercial Degussa P25 TiO2 nanoparticles. The reactant was then

Cr(VI) remediation from aqueous environment through modified-TiO₂-mediated photocatalytic reduction

• Rashmi Acharya,
• Brundabana Naik and
• Kulamani Parida

Beilstein J. Nanotechnol. 2018, 9, 1448–1470, doi:10.3762/bjnano.9.137

• facilitation by a RGO nanosheets, as shown in Figure 8. Shaikh et al. synthesized TiO2–RGO nanocomposites with uniformly dispersed 4–9 nm diameter TiO2 nanoparticles by a one-step solvothermal technique and evaluated its photocatalytic activity towards reduction of Cr(VI). The use of 1 wt % of RGO at acidic pH

• on TiO2 nanoparticles to form TiO2/Cu2O nanocomposites, a p–n nano-heterojunction having a built-in electric field at the interfaces. This built-in electric field largely prevented the recombination of photoexcited charge carriers, resulting in increased lifetime of photocarriers, induced higher

Room-temperature single-photon emitters in titanium dioxide optical defects

• Kelvin Chung,
• Yu H. Leung,
• Chap H. To,
• Aleksandra B. Djurišić and
• Snjezana Tomljenovic-Hanic

Beilstein J. Nanotechnol. 2018, 9, 1085–1094, doi:10.3762/bjnano.9.100

• , the characterisation of these single-photon emitting defects is presented in the next two subsections. The single-crystal TiO2 morphology was produced via the floating-zone growth process. The production of TiO2 nanoparticles in industry involves wet chemical processes. For both morphologies, thermal

Comparative study of antibacterial properties of polystyrene films with TiO_x and Cu nanoparticles fabricated using cluster beam technique

• Vladimir N. Popok,
• Cesarino M. Jeppesen,
• Peter Fojan,
• Anna Kuzminova,
• Jan Hanuš and
• Ondřej Kylián

Beilstein J. Nanotechnol. 2018, 9, 861–869, doi:10.3762/bjnano.9.80

• affecting in a destructive way the cell components but rendering innocuous products (mechanism ii) [5][6]. Thus, both Cu and TiO2 nanoparticles are excellent candidates for the formation of composites with antibacterial and antimicrobial properties. For more convenience in use and extended applications, NPs

Synthesis and characterization of two new TiO₂-containing benzothiazole-based imine composites for organic device applications

• Anna Różycka,
• Agnieszka Iwan,
• Krzysztof Artur Bogdanowicz,
• Michal Filapek,
• Natalia Górska,
• Damian Pociecha,
• Marek Malinowski,
• Patryk Fryń,
• Agnieszka Hreniak,
• Jakub Rysz,
• Paweł Dąbczyński and
• Monika Marzec

Beilstein J. Nanotechnol. 2018, 9, 721–739, doi:10.3762/bjnano.9.67

• this study TiO2 nanoparticles were used to modify the behavior of new, symmetrical and asymmetrical imines in order to investigate the electrochemical, structural and thermal properties of the imine:TiO2 composites with respect to the time stability under various air conditions and the amount of TiO2

• composites, the value of Rms decreases with increasing amount of titanium dioxide: 255.5 nm (3:1 w/w), 196.9 nm (3:2 w/w) and 149.7 nm (3:3 w/w). For pure titanium dioxide, the Rms was 45.26 nm. The most desired surface morphology would be a layer composed of TiO2 nanoparticles covered with SP1/SP2 molecules

Influence of the preparation method on the photocatalytic activity of Nd-modified TiO₂

• Patrycja Parnicka,
• Paweł Mazierski,
• Tomasz Grzyb,
• Wojciech Lisowski,
• Ewa Kowalska,
• Bunsho Ohtani,
• Adriana Zaleska-Medynska and
• Joanna Nadolna

Beilstein J. Nanotechnol. 2018, 9, 447–459, doi:10.3762/bjnano.9.43

• activity is strictly affected by physical properties such as crystalline structure and size, specific surface area, and the density of surface hydroxy groups [7]. The impact of the synthesis of TiO2 nanoparticles (NPs) on properties and morphology is important for understanding, creating and improving

Photocatalytic and adsorption properties of TiO₂-pillared montmorillonite obtained by hydrothermally activated intercalation of titanium polyhydroxo complexes

• Mikhail F. Butman,
• Nikolay L. Ovchinnikov,
• Nikita S. Karasev,
• Nataliya E. Kochkina,
• Alexander V. Agafonov and
• Alexandr V. Vinogradov

Beilstein J. Nanotechnol. 2018, 9, 364–378, doi:10.3762/bjnano.9.36

• . Keywords: adsorption; intercalation; mesoporosity; photocatalytic activity; pillared montmorillonite; titanium oxide; Introduction Titanium dioxide in its nanometer-sized form is one of the most promising modern photocatalysts [1]. However, the use of pure TiO2 nanoparticles is hindered by some

• stems from imparting higher acid resistance to the pillared MM, which is important when it is used for photocatalysis in highly acidic media. In particular, hydrothermal treatment accelerates crystallization and formation of clusters which grow and produce amorphous TiO2 nanoparticles in the interlayer

Bombyx mori silk/titania/gold hybrid materials for photocatalytic water splitting: combining renewable raw materials with clean fuels

• Stefanie Krüger,
• Michael Schwarze,
• Otto Baumann,
• Christina Günter,
• Michael Bruns,
• Christian Kübel,
• Dorothée Vinga Szabó,
• Rafael Meinusch,
• Verónica de Zea Bermudez and
• Andreas Taubert

Beilstein J. Nanotechnol. 2018, 9, 187–204, doi:10.3762/bjnano.9.21

• reported. All materials are monoliths with diameters of up to ca. 4.5 cm. The materials are macroscopically homogeneous and porous with surface areas between 170 and 210 m2/g. The diameter of the TiO2 nanoparticles (NPs) – mainly anatase with a minor fraction of brookite – and the Au NPs are on the order

Impact of titanium dioxide nanoparticles on purification and contamination of nematic liquid crystals

• Dmitrii Pavlovich Shcherbinin and
• Elena A. Konshina

Beilstein J. Nanotechnol. 2017, 8, 2766–2770, doi:10.3762/bjnano.8.275

• contamination. We have examined nematic liquid crystals with low (LC1) and high (LC2) ionic contamination and their composites with TiO2 nanoparticles. The impact of TiO2 nanoparticles on purification and contamination in LCs has been experimentally shown. The plane-parallel cells consisted of two glass

• the range from 20 Hz to 1 kHz. In this spectral range, the dispersion of dielectric permittivity is related to ionic conductivity. Figure 1a represents real and imaginary parts of the dielectric permittivity of initially low-contaminated liquid crystals (LC1) and their composites with TiO2

• nanoparticles. The increase of NP concentration led to the enhancement of the real and imaginary parts of the permittivity. We have observed an insignificant change in the spectra shown in Figure 1a. In contrast, the changes in the spectra were significant in the case of the initially high-contaminated LC2

CdSe nanorod/TiO₂ nanoparticle heterojunctions with enhanced solar- and visible-light photocatalytic activity

• Fakher Laatar,
• Hatem Moussa,
• Halima Alem,
• Lavinia Balan,
• Emilien Girot,
• Ghouti Medjahdi,
• Hatem Ezzaouia and
• Raphaël Schneider

Beilstein J. Nanotechnol. 2017, 8, 2741–2752, doi:10.3762/bjnano.8.273

• rue Jean Starcky, 68093 Mulhouse, France 10.3762/bjnano.8.273 Abstract CdSe nanorods (NRs) with an average length of ≈120 nm were prepared by a solvothermal process and associated to TiO2 nanoparticles (Aeroxide® P25) by annealing at 300 °C for 1 h. The content of CdSe NRs in CdSe/TiO2 composites was

• to develop TiO2-based solar cells. Core/shell TiO2/CdSe NRs were also prepared by growing CdSe quantum dots onto TiO2 NRs at high temperature [42]. In this paper, we report an investigation on the synthesis of CdSe-NR-sensitized TiO2 nanoparticles and on the use of these materials for the degradation

• possible mechanism is also discussed. Experimental Chemicals Cadmium acetate (Cd(OAc), 99.995%, Sigma), sodium selenite (Na2SeO3, 99%, Sigma), diethylenetriamine (99%, Sigma), TiO2 nanoparticles (Sigma-Aldrich, Aeroxide® P25, CAS: 13463-67-7), rhodamine B (RhB, >95%, Sigma), tert-butanol (t-BuOH, >99.5

Evaluating the toxicity of TiO₂-based nanoparticles to Chinese hamster ovary cells and Escherichia coli: a complementary experimental and computational approach

• Alicja Mikolajczyk,
• Natalia Sizochenko,
• Ewa Mulkiewicz,
• Anna Malankowska,
• Michal Nischk,
• Przemyslaw Jurczak,
• Seishiro Hirano,
• Grzegorz Nowaczyk,
• Adriana Zaleska-Medynska,
• Jerzy Leszczynski,
• Agnieszka Gajewicz and
• Tomasz Puzyn

Beilstein J. Nanotechnol. 2017, 8, 2171–2180, doi:10.3762/bjnano.8.216

• (Brunauer–Emmett–Teller surface, BET) of nanoparticles were discussed. Keywords: Au/Pd–TiO2 photocatalyst; bimetallic nanoparticles; nanotoxicity; nano-QSAR; second-generation nanoparticles; Introduction Unmodified titania (TiO2) nanoparticles (so-called first-generation NPs) represent a material that

• /Pd-TiO2 nanoparticles Titania (TiO2) modified with nanoparticles was obtained by hydrolysis of TIP in a water/AOT/cyclohexane microemulsion containing Au and Pd precursors in water cores. Mixing was carried out for 1 h under nitrogen; Au and Pd were then reduced by dropwise addition of a

Three-in-one approach towards efficient organic dye-sensitized solar cells: aggregation suppression, panchromatic absorption and resonance energy transfer

• Jayita Patwari,
• Samim Sardar,
• Bo Liu,
• Peter Lemmens and
• Samir Kumar Pal

Beilstein J. Nanotechnol. 2017, 8, 1705–1713, doi:10.3762/bjnano.8.171

• increased absorption window, FRET-enhanced photocurrent and the prevention of SQ2 aggregation. Experimental Reagents TiO2 nanoparticles (21 nm), protoporphyrin IX (PPIX), platinum chloride (H2PtCl6), lithium iodide (LiI), 4-tert-butylpyridine (TBP) and iodine (I2) were purchased from Sigma-Aldrich. Squarine

Two-dimensional carbon-based nanocomposites for photocatalytic energy generation and environmental remediation applications

• Suneel Kumar,
• Ashish Kumar,
• Ashish Bahuguna,
• Vipul Sharma and
• Venkata Krishnan

Beilstein J. Nanotechnol. 2017, 8, 1571–1600, doi:10.3762/bjnano.8.159

• ]. This composite prepared by a two-step hydrothermal process lead to uniform dispersion of TiO2 nanopartilces over layered MoS2–graphene (MG), as shown in Figure 8. Herein, the MG hybrid plays a crucial role for charge separation in UV-excited TiO2 nanoparticles and the observed hydrogen production rate

High photocatalytic activity of Fe₂O₃/TiO₂ nanocomposites prepared by photodeposition for degradation of 2,4-dichlorophenoxyacetic acid

• Shu Chin Lee,
• Hendrik O. Lintang and
• Leny Yuliati

Beilstein J. Nanotechnol. 2017, 8, 915–926, doi:10.3762/bjnano.8.93

• and TiO2 nanoparticles that improved charge transfer and suppressed electron–hole recombination. A further investigation on the role of the active species on Fe2O3/TiO2 confirmed that the crucial active species were both holes and superoxide radicals. The Fe2O3(0.5)/TiO2 sample also showed good

• out at ambient conditions [14]. Even though high activity was obtained, evidence of the formation of good contact between Fe2O3 and TiO2 nanoparticles was not provided. Recently, the photodeposition method has been proposed as a suitable method to directly investigate the role of added copper or

• lanthanum species without such heat-treatment effects [20][21]. Moreover, the modification of TiO2 nanoparticles by photodeposition resulted in an improved photocatalytic activity as compared to unmodified TiO2 [20][21][22]. Therefore, it is meaningful to employ the photodeposition method to prepare Fe2O3

Functionalized TiO₂ nanoparticles by single-step hydrothermal synthesis: the role of the silane coupling agents

• Antoine R. M. Dalod,
• Lars Henriksen,
• Tor Grande and
• Mari-Ann Einarsrud

Beilstein J. Nanotechnol. 2017, 8, 304–312, doi:10.3762/bjnano.8.33

• versatile hydrothermal synthesis route to in situ functionalized TiO2 nanoparticles was developed using titanium(IV) isopropoxide as Ti-precursor and selected silane coupling agents (3-aminopropyltriethoxysilane (APTES), 3-(2-aminoethylamino)propyldimethoxymethylsilane (AEAPS), and n-decyltriethoxysilane

• route was demonstrated, and by selecting the type of silane coupling agent the surface properties of the TiO2 nanoparticles could be tailored. This synthesis route has been further developed into a two-step synthesis to TiO2–SiO2 core–shell nanoparticles. Combustion of the silane coupling agents up to

• Because of the high surface-to-volume ratio, the intrinsic properties of titanium dioxide (TiO2) nanoparticles have led to exploitation in many fields such as in photocatalysis [1], solar cells [2], and in biomedical applications [3]. The naturally occurring phases of TiO2 are rutile (thermodynamically

Photocatalysis applications of some hybrid polymeric composites incorporating TiO₂ nanoparticles and their combinations with SiO₂/Fe₂O₃

• Andreea Laura Chibac,
• Tinca Buruiana,
• Violeta Melinte and
• Emil C. Buruiana

Beilstein J. Nanotechnol. 2017, 8, 272–286, doi:10.3762/bjnano.8.30

• nanocatalysts. Keywords: hybrid polymer composites; maghemite nanoparticles; photocatalysis; TiO2 nanoparticles; UV–visible irradiation; Introduction Over the last years, titania nanomaterials have attracted a lot of attention as they have found numerous applications in the field of dye-sensitized solar cells

• , they are active only in UV light (<4% of sunlight) owing to their wide bandgap (3.2 eV), which absorbs photons with wavelengths shorter than 400 nm. Also, TiO2 nanoparticles (NPs) have a low adsorption capacity for hydrophobic molecules, and if they are used for water treatment, severe problems during

• crystallite size of anatase, calculated by applying the Scherrer equation to the major diffraction peak was found to be 21.8 nm. Besides, the TEM image of TiO2 nanoparticles (Figure 1a, inset) sustains that spherical TiO2 NPs with a relatively uniform size distribution (particle dimensions in the range of 25

Colorimetric gas detection by the varying thickness of a thin film of ultrasmall PTSA-coated TiO₂ nanoparticles on a Si substrate

• Urmas Joost,
• Andris Šutka,
• Meeri Visnapuu,
• Aile Tamm,
• Meeri Lembinen,
• Mikk Antsov,
• Kathriin Utt,
• Krisjanis Smits,
• Ergo Nõmmiste and
• Vambola Kisand

Beilstein J. Nanotechnol. 2017, 8, 229–236, doi:10.3762/bjnano.8.25

• Valdena 3/7, 1048 Riga, Latvia Institute of Solid State Physics, University of Latvia, Kengaraga 8, Riga LV-1063, Latvia 10.3762/bjnano.8.25 Abstract Colorimetric gas sensing is demonstrated by thin films based on ultrasmall TiO2 nanoparticles (NPs) on Si substrates. The NPs are bound into the film by p

• . The color response is rapid and changes reversibly within seconds of exposure. The sensing element is extremely simple and cheap, and can be fabricated by common coating processes. Keywords: colorimetric gas sensing; p-toluenesulfonic acid (PTSA); TiO2 nanoparticles; Introduction The apparent color

• ultrasmall TiO2 nanoparticles (NPs) for a colorimetric gas sensor. The functional thin film is extremely simple, consisting of TiO2 NPs and the elastic binding agent p-toluenesulfonic acid (PTSA) on a Si substrate. It is not necessary to use particles with narrow size distributions of diameters in well