Room-temperature single-photon emitters in titanium dioxide optical defects

• Kelvin Chung,
• Yu H. Leung,
• Chap H. To,
• Aleksandra B. Djurišić and
• Snjezana Tomljenovic-Hanic

Beilstein J. Nanotechnol. 2018, 9, 1085–1094, doi:10.3762/bjnano.9.100

• emission. ZnO is the only metal oxide reported to host single-photon emitting defects at room temperature and was recently shown to exhibit stable fluorescence when uptaken into skin cells, making it a viable biomarker [11]. Titanium dioxide (TiO2) is a well-studied wide-bandgap semiconductor, its

Synthesis and characterization of two new TiO₂-containing benzothiazole-based imine composites for organic device applications

• Anna Różycka,
• Agnieszka Iwan,
• Krzysztof Artur Bogdanowicz,
• Michal Filapek,
• Natalia Górska,
• Damian Pociecha,
• Marek Malinowski,
• Patryk Fryń,
• Agnieszka Hreniak,
• Jakub Rysz,
• Paweł Dąbczyński and
• Monika Marzec

Beilstein J. Nanotechnol. 2018, 9, 721–739, doi:10.3762/bjnano.9.67

• physical parameters of titanium dioxide TiO2 powder was prepared via the sol–gel technique using titanium(IV) isopropoxide (TIPO) as a precursor as was fully described in our previous paper [34]. The obtained TiO2 powder exhibited an anatase form, which was confirmed from X-ray diffraction (XRD

• temperatures of both imines addition of TiO2 to SP2 imine significantly changed the POM texture of imine values of the energy gap and HOMO–LUMO levels of both imines decreased with increasing addition of titanium dioxide TiO2 has an influence on the structural properties of SP1 and SP2 imines the imine:TiO2

Fabrication and photoactivity of ionic liquid–TiO₂ structures for efficient visible-light-induced photocatalytic decomposition of organic pollutants in aqueous phase

• Anna Gołąbiewska,
• Marta Paszkiewicz-Gawron,
• Aleksandra Sadzińska,
• Wojciech Lisowski,
• Ewelina Grabowska,
• Adriana Zaleska-Medynska and
• Justyna Łuczak

Beilstein J. Nanotechnol. 2018, 9, 580–590, doi:10.3762/bjnano.9.54

• pollutants in aqueous and gas phases requires visible-light responsive, stable materials and a basic understanding of these materials [1][2][3][4]. Although various semiconductors are considered for environmental pollution abatement, titanium dioxide (TiO2) is still the most promising due to its stability

Influence of the preparation method on the photocatalytic activity of Nd-modified TiO₂

• Patrycja Parnicka,
• Paweł Mazierski,
• Tomasz Grzyb,
• Wojciech Lisowski,
• Ewa Kowalska,
• Bunsho Ohtani,
• Adriana Zaleska-Medynska and
• Joanna Nadolna

Beilstein J. Nanotechnol. 2018, 9, 447–459, doi:10.3762/bjnano.9.43

• light-induced degradation of the model pollutant in aqueous solution. Keywords: heterogeneous photocatalysis; hydrothermal method; modified TiO2; neodymium; sol–hydrothermal method; Introduction Heterogeneous photocatalysis based on titanium dioxide (TiO2) has become the focus of numerous studies due

Sugarcane juice derived carbon dot–graphitic carbon nitride composites for bisphenol A degradation under sunlight irradiation

• Lan Ching Sim,
• Jing Lin Wong,
• Chen Hong Hak,
• Jun Yan Tai,
• Kah Hon Leong and
• Pichiah Saravanan

Beilstein J. Nanotechnol. 2018, 9, 353–363, doi:10.3762/bjnano.9.35

• absorption spectra after titanium dioxide (TiO2) loading [28] and acid treatment [29], the incorporation of CDs into g-C3N4 consistently red-shifted the absorption spectra towards the visible and NIR region. However, the photocatalytic performance of the composites is possibly limited under NIR light

CdSe nanorod/TiO₂ nanoparticle heterojunctions with enhanced solar- and visible-light photocatalytic activity

• Fakher Laatar,
• Hatem Moussa,
• Halima Alem,
• Lavinia Balan,
• Emilien Girot,
• Ghouti Medjahdi,
• Hatem Ezzaouia and
• Raphaël Schneider

Beilstein J. Nanotechnol. 2017, 8, 2741–2752, doi:10.3762/bjnano.8.273

• conversion of solar energy to chemical energy, for example, via water splitting to produce hydrogen, is the topic of numerous current research projects. Titanium dioxide (TiO2) has been widely investigated over the last three decades and has been demonstrated to be of high potential [1][2]. However, TiO2

Fabrication of hierarchically porous TiO₂ nanofibers by microemulsion electrospinning and their application as anode material for lithium-ion batteries

• Jin Zhang,
• Yibing Cai,
• Xuebin Hou,
• Xiaofei Song,
• Pengfei Lv,
• Huimin Zhou and
• Qufu Wei

Beilstein J. Nanotechnol. 2017, 8, 1297–1306, doi:10.3762/bjnano.8.131

• China 10.3762/bjnano.8.131 Abstract Titanium dioxide (TiO2) nanofibers have been widely applied in various fields including photocatalysis, energy storage and solar cells due to the advantages of low cost, high abundance and nontoxicity. However, the low conductivity of ions and bulk electrons hinder

• density [5][6][7][8]. So far, among all the commercial lithium-ion batteries, graphite plays an extremely important role in anode materials; nevertheless, structural deformation, electrical disconnection and the initial loss of capacity hinder its further development [9][10]. Titanium dioxide (TiO2) is

High photocatalytic activity of Fe₂O₃/TiO₂ nanocomposites prepared by photodeposition for degradation of 2,4-dichlorophenoxyacetic acid

• Shu Chin Lee,
• Hendrik O. Lintang and
• Leny Yuliati

Beilstein J. Nanotechnol. 2017, 8, 915–926, doi:10.3762/bjnano.8.93

• , titanium dioxide (TiO2) has been the foremost established material for degradation of organic pollutants [1][2]. In addition to its nontoxicity, abundance and relatively low cost, TiO2 also shows excellent photocatalytic activity in many degradation reactions. Unfortunately, the photocatalytic performance

Synthesis of graphene–transition metal oxide hybrid nanoparticles and their application in various fields

• Arpita Jana,
• Elke Scheer and
• Sebastian Polarz

Beilstein J. Nanotechnol. 2017, 8, 688–714, doi:10.3762/bjnano.8.74

• precise, in the following, we categorise the graphene–TMO semiconductor NP hybrids on the basis of their counterpart material oxide (from titanium to zinc) following the periodic table. Titanium dioxide (TiO2)–graphene hybrids Nanocrystalline TiO2 is an interesting material because of its unique optical

Functionalized TiO₂ nanoparticles by single-step hydrothermal synthesis: the role of the silane coupling agents

• Antoine R. M. Dalod,
• Lars Henriksen,
• Tor Grande and
• Mari-Ann Einarsrud

Beilstein J. Nanotechnol. 2017, 8, 304–312, doi:10.3762/bjnano.8.33

• Because of the high surface-to-volume ratio, the intrinsic properties of titanium dioxide (TiO2) nanoparticles have led to exploitation in many fields such as in photocatalysis [1], solar cells [2], and in biomedical applications [3]. The naturally occurring phases of TiO2 are rutile (thermodynamically

Performance of natural-dye-sensitized solar cells by ZnO nanorod and nanowall enhanced photoelectrodes

• Saif Saadaoui,
• Mohamed Aziz Ben Youssef,
• Moufida Ben Karoui,
• Rached Gharbi,
• Emanuele Smecca,
• Vincenzina Strano,
• Salvo Mirabella,
• Alessandra Alberti and
• Rosaria A. Puglisi

Beilstein J. Nanotechnol. 2017, 8, 287–295, doi:10.3762/bjnano.8.31

• represents the photoelectrode, composed of a wide band gap semiconductor thin layer coated on transparent conducting oxide (TCO) films. A mesoporous film layer is used as a semiconductor in the photoelectrode. Because of its stability and easy synthesis, titanium dioxide (TiO2) is mostly used as the

Flexible photonic crystal membranes with nanoparticle high refractive index layers

• Torben Karrock,
• Moritz Paulsen and
• Martina Gerken

Beilstein J. Nanotechnol. 2017, 8, 203–209, doi:10.3762/bjnano.8.22

• highly flexible photonic crystal slabs by utilizing nanoreplication of a linear grating nanostructure with a period of 400 nm into a polydimethylsiloxane (PDMS) membrane and subsequent spin coating of titanium dioxide (TiO2) nanoparticles. Investigations with 300 nm and 500 nm gratings lead to similar

• nm period and 140 nm deep linear grating nanostructure is coated with a high-refractive index layer of titanium dioxide (TiO2) nanoparticles. Resonances are observed in the normal-incidence transmission spectrum between crossed-polarization filters. The resonance shift is investigated as a function

Optical and photocatalytic properties of TiO₂ nanoplumes

• Viviana Scuderi,
• Massimo Zimbone,
• Maria Miritello,
• Giuseppe Nicotra,
• Giuliana Impellizzeri and
• Vittorio Privitera

Beilstein J. Nanotechnol. 2017, 8, 190–195, doi:10.3762/bjnano.8.20

• ; photocatalysis; titanium dioxide (TiO2); Introduction Today water, energy, and food are the most urgent problems of humanity. Since the seminal work of Honda and Fujishima in 1972 where photo-induced decomposition of water was discovered [1], semiconductor photocatalysis has shown great potential not only for

The cleaner, the greener? Product sustainability assessment of the biomimetic façade paint Lotusan^® in comparison to the conventional façade paint Jumbosil^®

• Florian Antony,
• Rainer Grießhammer,
• Thomas Speck and
• Olga Speck

Beilstein J. Nanotechnol. 2016, 7, 2100–2115, doi:10.3762/bjnano.7.200

• mainly because of Lotusan®’s higher content of titanium dioxide (TiO2). Regarding the remaining impact indicators both façade paints are equal within the calculation inaccuracy. Contributions by life-cycle stages: The key issue of the contribution analysis is a clarification of the composition of the

Nanostructured TiO₂-based gas sensors with enhanced sensitivity to reducing gases

• Wojciech Maziarz,
• Anna Kusior and
• Anita Trenczek-Zajac

Beilstein J. Nanotechnol. 2016, 7, 1718–1726, doi:10.3762/bjnano.7.164

• to display better gas selectivity and sensitivity [1][2]. Additionally, open nanostructures facilitate the penetration of gas, and as a consequence, reduces the response time. Titanium dioxide (TiO2) is effectively used in environmental and energy production applications such as dye-sensitized solar

Scanning probe microscopy studies on the adsorption of selected molecular dyes on titania

• Jakub S. Prauzner-Bechcicki,
• Lukasz Zajac,
• Piotr Olszowski,
• Res Jöhr,
• Antoine Hinaut,
• Thilo Glatzel,
• Bartosz Such,
• Ernst Meyer and
• Marek Szymonski

Beilstein J. Nanotechnol. 2016, 7, 1642–1653, doi:10.3762/bjnano.7.156

• dianhydride (PTCDA); phtalocyanines; porphyrins; rutile; scanning probe microscopy; scanning tunneling microscopy (STM); titanium dioxide (TiO2); Introduction Today it comes as no surprise that photovoltaic devices can be made of materials other than silicon. Nanocrystalline materials accompanied by organic

Fast diffusion of silver in TiO₂ nanotube arrays

• Wanggang Zhang,
• Yiming Liu,
• Diaoyu Zhou,
• Hui Wang,
• Wei Liang and
• Fuqian Yang

Beilstein J. Nanotechnol. 2016, 7, 1129–1140, doi:10.3762/bjnano.7.105

• the outmost surface of TiO2 nanotubes. Probably there are hardly any Ag nanocrystals formed inside the TiO2 nanotubes through the migration of Ag. Keywords: activation energy; fast diffusion; magnetron sputtering; silver; TiO2 nanotube; Introduction Titanium dioxide (TiO2) has gained great attention

Comparison of the interactions of daunorubicin in a free form and attached to single-walled carbon nanotubes with model lipid membranes

• Dorota Matyszewska

Beilstein J. Nanotechnol. 2016, 7, 524–532, doi:10.3762/bjnano.7.46

• fields. Such magnetic nanoparticles conjugated with DNR were reported to induce apoptosis of cancer cell lines [11][12]. Other examples of nanoparticles include titanium dioxide (TiO2) and gold nanoparticles (AuNPs) [13][14]. In the latter case the nanoparticles were also modified with aptamer – single

Impact of ultrasonic dispersion on the photocatalytic activity of titania aggregates

• Hoai Nga Le,
• Frank Babick,
• Klaus Kühn,
• Minh Tan Nguyen,
• Michael Stintz and
• Gianaurelio Cuniberti

Beilstein J. Nanotechnol. 2015, 6, 2423–2430, doi:10.3762/bjnano.6.250

• oxidation, discoloration, mineralization, and degradation of organic pollutants [1][2]. Photocatalysis is an example of an AOP that has been effectively applied for the treatment of highly polluted water such as dye sewage [3][4]. Among the materials for this application, titanium dioxide (TiO2) is a very

NanoE-Tox: New and in-depth database concerning ecotoxicity of nanomaterials

• Katre Juganson,
• Angela Ivask,
• Irina Blinova,
• Monika Mortimer and
• Anne Kahru

Beilstein J. Nanotechnol. 2015, 6, 1788–1804, doi:10.3762/bjnano.6.183

• database NanoE-Tox that is available as Supporting Information File 2. The database is based on existing literature on ecotoxicology of eight ENMs with different chemical composition: carbon nanotubes (CNTs), fullerenes, silver (Ag), titanium dioxide (TiO2), zinc oxide (ZnO), cerium dioxide (CeO2), copper

• : carbon nanotubes (CNTs), fullerenes, silver (Ag), titanium dioxide (TiO2), zinc oxide (ZnO), cerium dioxide (CeO2), copper oxide (CuO), and iron oxide (FeOx; Fe2O3, Fe3O4). Furthermore, all these ENMs, except CuO, are listed by the Organisation for Economic Co-operation and Development (OECD) Working

Nanotechnology in the real world: Redeveloping the nanomaterial consumer products inventory

• Marina E. Vance,
• Todd Kuiken,
• Eric P. Vejerano,
• Sean P. McGinnis,
• Michael F. Hochella Jr.,
• David Rejeski and
• Matthew S. Hull

Beilstein J. Nanotechnol. 2015, 6, 1769–1780, doi:10.3762/bjnano.6.181

• . Titanium dioxide (TiO2), silicon dioxide, and zinc oxide are the most produced nanomaterials worldwide (on a mass basis) and the global annual production of silver nanoparticles represents only 2% of that of TiO2 [20][21]. However, silver nanoparticles are the most popular advertised nanomaterial in the

Transformation of hydrogen titanate nanoribbons to TiO₂ nanoribbons and the influence of the transformation strategies on the photocatalytic performance

• Melita Rutar,
• Nejc Rozman,
• Matej Pregelj,
• Carla Bittencourt,
• Romana Cerc Korošec,
• Andrijana Sever Škapin,
• Aleš Mrzel,
• Srečo D. Škapin and
• Polona Umek

Beilstein J. Nanotechnol. 2015, 6, 831–844, doi:10.3762/bjnano.6.86

• in air. Keywords: doping; nanoribbon; photocatalytic performance; titanate; titanium dioxide (TiO2); transformation; Introduction Titanium dioxide (TiO2) is a technologically important material due to its remarkable combination of properties, its chemical stability and nontoxicity [1][2]. In

In situ scanning tunneling microscopy study of Ca-modified rutile TiO₂(110) in bulk water

• Giulia Serrano,
• Beatrice Bonanni,
• Tomasz Kosmala,
• Marco Di Giovannantonio,
• Ulrike Diebold,
• Klaus Wandelt and
• Claudio Goletti

Beilstein J. Nanotechnol. 2015, 6, 438–443, doi:10.3762/bjnano.6.44

• microscopy; solid/liquid interface; titanium dioxide reconstruction; Introduction Metal oxide surfaces (in particular titanium dioxide (TiO2) surfaces) covered by an alkaline-earth-metal overlayer have been investigated in recent years in experiments [1][2][3][4][5] and theoretical studies [6], considering

Growth and characterization of CNT–TiO₂ heterostructures

• Yucheng Zhang,
• Ivo Utke,
• Johann Michler,
• Gabriele Ilari,
• Marta D. Rossell and
• Rolf Erni

Beilstein J. Nanotechnol. 2014, 5, 946–955, doi:10.3762/bjnano.5.108

• /metal oxide material systems. Keywords: atomic layer deposition (ALD); carbon nanotubes; electron energy loss spectroscopy (EELS); interface; titanium dioxide (TiO2); transmission electron microscopy (TEM); Introduction Since the discovery by Iijima in 1991, carbon nanotubes (CNTs) have always been on

A visible-light-driven composite photocatalyst of TiO₂ nanotube arrays and graphene quantum dots

• Donald K. L. Chan,
• Po Ling Cheung and
• Jimmy C. Yu

Beilstein J. Nanotechnol. 2014, 5, 689–695, doi:10.3762/bjnano.5.81

• ][2]. Among various photocatalysts, nanostructured titanium dioxide (TiO2) is the most widely used because of its high activity, long-term stability and low production cost [3][4]. However, pure TiO2 is not efficient for solar-driven applications because it requires UV excitation [5]. Belonging to one