Near-infrared photoactive Ag-Zn-Ga-S-Se quantum dots for high-performance quantum dot-sensitized solar cells

• Roopakala Kottayi,
• Ilangovan Veerappan and
• Ramadasse Sittaramane

Beilstein J. Nanotechnol. 2022, 13, 1337–1344, doi:10.3762/bjnano.13.110

• nanocrystals. The X-ray diffraction pattern confirms the hexagonal structure. Due to the near-infrared light absorption capability, the synthesized QDs were used as the sensitizer to fabricate QDSCs. The fabricated QDSCs were characterized by using electrochemical impedance spectroscopy and photovoltaic

• QDSCs. Physical characterization The crystalline structure and size of the synthesized QDs were examined by X-ray diffraction (Riganku Ultima IV XRD spectrometer with nickel-filtered Cu Kα radiation with a step width of 0.02°) High-resolution transmission electron microscopy was carried out on a JEOL

Recent trends in Bi-based nanomaterials: challenges, fabrication, enhancement techniques, and environmental applications

• Vishal Dutta,
• Ankush Chauhan,
• Ritesh Verma,
• C. Gopalkrishnan and
• Van-Huy Nguyen

Beilstein J. Nanotechnol. 2022, 13, 1316–1336, doi:10.3762/bjnano.13.109

• intermediates from the synthesis process into photocatalysts to alter the energy band structure and increase photocatalytic activity [89]. A simple two-step technique was used to develop a novel compound photocatalyst of Bi/BiOBr-Bi5+ [90]. X-ray diffraction, field-emission transmission electron microscopy, and

Rapid fabrication of MgO@g-C₃N₄ heterojunctions for photocatalytic nitric oxide removal

• Minh-Thuan Pham,
• Duyen P. H. Tran,
• Xuan-Thanh Bui and
• Sheng-Jie You

Beilstein J. Nanotechnol. 2022, 13, 1141–1154, doi:10.3762/bjnano.13.96

• properties of the materials. Scanning electron microscopy (SEM) and high-resolution transmission electron microscopy (HR-TEM) were used to assess the morphology of the materials. The crystal phase of the materials was determined by X-ray diffraction (XRD) with a measurement range of 10°–80°. Fourier

Green synthesis of zinc oxide nanoparticles toward highly efficient photocatalysis and antibacterial application

• Vo Thi Thu Nhu,
• Nguyen Duy Dat,
• Le-Minh Tam and
• Nguyen Hoang Phuong

Beilstein J. Nanotechnol. 2022, 13, 1108–1119, doi:10.3762/bjnano.13.94

• reactions that form zinc resinate are shown in Equation 1 and Equation 2. The schematic illustration of the synthesis of ZnO nanoparticles is shown in Figure 1. Methods for determining the characterization of the synthesized material The phase of the synthesized material was determined by X-ray diffraction

Spindle-like MIL101(Fe) decorated with Bi₂O₃ nanoparticles for enhanced degradation of chlortetracycline under visible-light irradiation

• Chen-chen Hao,
• Fang-yan Chen,
• Kun Bian,
• Yu-bin Tang and
• Wei-long Shi

Beilstein J. Nanotechnol. 2022, 13, 1038–1050, doi:10.3762/bjnano.13.91

• . Characterization of the as-prepared catalyst The crystalline structure of the prepared photocatalyst was analyzed by X-ray diffraction spectrometry (Empyrean, Panalytical, Holland) with Cu Kα radiation at a scanning speed of 7 °/min. The morphology of the samples was observed by scanning electron microscopy (SEM

Electrocatalytic oxygen reduction activity of AgCoCu oxides on reduced graphene oxide in alkaline media

• Iyyappan Madakannu,
• Indrajit Patil,
• Bhalchandra Kakade and
• Kasibhatta Kumara Ramanatha Datta

Beilstein J. Nanotechnol. 2022, 13, 1020–1029, doi:10.3762/bjnano.13.89

• and crystallinity of the assembled binary and ternary metallic oxide NPs, powder X-ray diffraction (PXRD) measurements were carried out. The PXRD patterns of the binary and ternary NPs on rGO showed peaks located at 2θ = 38.1°, 44.2°, 64.3°, and 77.1°, which could be indexed to the (111), (200), (220

Efficient liquid exfoliation of KP₁₅ nanowires aided by Hansen's empirical theory

• Zhaoxuan Huang,
• Zhikang Jiang,
• Nan Tian,
• Disheng Yao,
• Fei Long,
• Yanhan Yang and
• Danmin Liu

Beilstein J. Nanotechnol. 2022, 13, 788–795, doi:10.3762/bjnano.13.69

• control the temperature. To prevent sample drift, SiO2 (300 nm)/Si substrates with tested KP15 samples were attached by fixtures to the Linkam THMS600 cryostat. Results and Discussion KP15 bulks, prepared by the gas-phase-transfer method, had a flat and smooth surface shown in Figure 1a. The X-ray

• diffraction patterns of the synthesized KP15 were both theoretically calculated and experimentally measured. The consistency between the two patterns shows that there is no impurity phase (Figure 1b), which confirms an excellent crystallization quality of the KP15 bulks. Measurement of the absorption

Recent advances in nanoarchitectures of monocrystalline coordination polymers through confined assembly

• Lingling Xia,
• Qinyue Wang and
• Ming Hu

Beilstein J. Nanotechnol. 2022, 13, 763–777, doi:10.3762/bjnano.13.67

• the grown coordination polymers can be distinguished by X-ray diffraction analysis [124][125][126][127]. However, the flexibility of the frameworks brought unexpected phenomena [128][129]. The shell crystal could first yield to the core crystal, making the whole composite present a single phase as the

Hierarchical Bi₂WO₆/TiO₂-nanotube composites derived from natural cellulose for visible-light photocatalytic treatment of pollutants

• Zehao Lin,
• Zhan Yang and
• Jianguo Huang

Beilstein J. Nanotechnol. 2022, 13, 745–762, doi:10.3762/bjnano.13.66

• the practical content (72.9 wt %) of the Bi2WO6 component in the 70%−Bi2WO6/TiO2-NT nanocomposite. Characterization Powder X-ray diffraction (XRD) patterns of the samples were obtained from the Rigaku Ultima IV diffractometer with a Cu Kα (λ = 0.15405 nm) radiation source. Fourier transform infrared

A nonenzymatic reduced graphene oxide-based nanosensor for parathion

• Sarani Sen,
• Anurag Roy,
• Ambarish Sanyal and
• Parukuttyamma Sujatha Devi

Beilstein J. Nanotechnol. 2022, 13, 730–744, doi:10.3762/bjnano.13.65

• phase of GO and RGO was characterized by X-ray diffraction (XRD) using a X’pertpro MPD XRD (PAN analytical B.V., the Netherlands) with Cu Kα radiation (λ = 1.5406 Å). Scanning electron microscopy (SEM) of the modified electrode was conducted on a JEOLEVO® 18 special edition (model: ZEISS EVO-MA 10) at

Design and selection of peptides to block the SARS-CoV-2 receptor binding domain by molecular docking

• Kendra Ramirez-Acosta,
• Ivan A. Rosales-Fuerte,
• J. Eduardo Perez-Sanchez,
• Alfredo Nuñez-Rivera,
• Josue Juarez and
• Ruben D. Cadena-Nava

Beilstein J. Nanotechnol. 2022, 13, 699–711, doi:10.3762/bjnano.13.62

• , hydrogen bonds, and interactions of the selected ligand and protein docked complexes were analyzed by PyMOL (version 2.4) and LigPlot+ (version 2.2) [33][34]. Protein and ligand preparation for AutoDock Vina AutoDock Vina (1.1.2) software was employed for all docking experiments [21]. The X-ray diffraction

Nanoarchitectonics of the cathode to improve the reversibility of Li–O₂ batteries

• Hien Thi Thu Pham,
• Jonghyeok Yun,
• So Yeun Kim,
• Sang A Han,
• Jung Ho Kim,
• Jong-Won Lee and
• Min-Sik Park

Beilstein J. Nanotechnol. 2022, 13, 689–698, doi:10.3762/bjnano.13.61

• the carbonization process. After the carbonization and chemical etching processes, the sizes of the ZnxCoy particles were slightly decreased due to the thermal evaporation of organic linkers and metal ions, maintaining free spaces in the particles. According to the X-ray diffraction (XRD) patterns of

Sodium doping in brookite TiO₂ enhances its photocatalytic activity

• Boxiang Zhuang,
• Honglong Shi,
• Honglei Zhang and
• Zeqian Zhang

Beilstein J. Nanotechnol. 2022, 13, 599–609, doi:10.3762/bjnano.13.52

• bandgap values of these four samples. Structural phase diagram, chemical composition, and morphology The crystal structure of samples calcinated at 300–900 °C was characterized by powder X-ray diffraction (XRD), as shown in Figure 3a. The sample calcinated at 300 °C is a mixture of brookite (B) and

• activity of these samples. Quantitative phase analysis of X-ray diffraction patterns provides the structure phase diagram, as shown in Figure 3b. It indicates that the weight fraction of the brookite phase can be up to 82% when samples were calcinated at 500 °C. Note that the sample at 600 °C precipitated

• little due to the finite content of sodium in the brookite phase. The X-ray diffraction experiment suggests the existence of sodium in the samples. Next, we verified in which structure sodium is present. Figure 4a shows four typical morphologies of products observed via SEM. Samples calcinated at 300–500

A new method for obtaining the magnetic shape anisotropy directly from electron tomography images

• Cristian Radu,
• Ioana D. Vlaicu and
• Andrei C. Kuncser

Beilstein J. Nanotechnol. 2022, 13, 590–598, doi:10.3762/bjnano.13.51

• , X-ray diffraction, magnetometry [4], transmission/scanning electron imaging [5][6], small-angle scattering techniques [7], dynamic light scattering, laser diffraction [8][9], resonant mass measurement, and spatial filter velocimetry. Each of these has certain features (i.e., ease of access, ease of

• technique. The “translation” of the experimentally measured parameter to the parameter of interest (particle size in this case) is always accomplished by imperfect assumptions or extrapolations in the mathematical models. For example, in the case of X-ray diffraction, the mean crystal size is provided only

• microscopy (STEM) operation mode, using the high-angle annular dark-field (HAADF) detectors and an appropriate camera length. The TEM specimen was prepared by a standard powder method, using a 300 Mesh, lacey Carbon, Cu grid. X-ray diffraction (XRD) has been performed on MNPs using a Bruker D8 Advance

Influence of thickness and morphology of MoS₂ on the performance of counter electrodes in dye-sensitized solar cells

• Lam Thuy Thi Mai,
• Hai Viet Le,
• Ngan Kim Thi Nguyen,
• Van La Tran Pham,
• Thu Anh Thi Nguyen,
• Nguyen Thanh Le Huynh and
• Hoang Thai Nguyen

Beilstein J. Nanotechnol. 2022, 13, 528–537, doi:10.3762/bjnano.13.44

• , respectively. For comparison, DSSCs based on Pt/FTO CE (DSSCs-Pt) were also fabricated under the same conditions. Characterizations of MoS2 thin films X-ray diffraction (XRD) analysis was carried out using a D8 Advance (Bruker, Germany) with a copper anode (λKα = 1.54 Å). Raman spectroscopy measurements were

Tubular glassy carbon microneedles with fullerene-like tips for biomedical applications

• Sharali Malik and
• George E. Kostakis

Beilstein J. Nanotechnol. 2022, 13, 455–461, doi:10.3762/bjnano.13.38

• the nanoarchitectonics concept of bottom-up creation of functional materials, we use methane rather than a polymer to form glassy carbon. Here we show that tubular glassy carbon microneedles with fullerene-like tips form when methane undergoes pyrolysis on a curved alumina surface. X-ray diffraction

• Raman spectroscopy (WiTec CRM200, laser excitation at 632.8 nm), scanning electron microscopy (SEM Leo 1530, with a spatial resolution of 1 nm at 20 kV and 3 nm at 1 kV, equipped with an energy-dispersive X-ray analysis system EDX INCA 400 from Oxford Instruments), and X-ray diffraction (STOE STADI-P

The role of sulfonate groups and hydrogen bonding in the proton conductivity of two coordination networks

• Ali Javed,
• Felix Steinke,
• Stephan Wöhlbrandt,
• Hana Bunzen,
• Norbert Stock and
• Michael Tiemann

Beilstein J. Nanotechnol. 2022, 13, 437–443, doi:10.3762/bjnano.13.36

• h in dry air. This process is supposed to remove surface-adsorbed water, such as residues from the synthesis process or from exposure to humid conditions. Powder X-ray diffraction confirmed that this process does not affect the crystallinity of the two materials, and no phase transformation was

• within 12 h. The compounds were collected via filtration, dried under ambient conditions, and identified by powder X-ray diffraction. [Mg(H2O)2(H3L)]·H2O was obtained as colorless needles (240 mg, 36%) and [Pb2(HL)]·H2O as small colorless crystals (152 mg, 38%). PXRD data at a relative humidity of 90

A non-enzymatic electrochemical hydrogen peroxide sensor based on copper oxide nanostructures

• Irena Mihailova,
• Vjaceslavs Gerbreders,
• Marina Krasovska,
• Eriks Sledevskis,
• Valdis Mizers,
• Andrejs Bulanovs and
• Andrejs Ogurcovs

Beilstein J. Nanotechnol. 2022, 13, 424–436, doi:10.3762/bjnano.13.35

• amorphous background indicates a high degree of crystallinity of the obtained samples. The X-ray diffraction pattern shows a large number of crystallographic planes corresponding to the CuO (tenorite) lattice; however, the dominant orientation corresponds to the direction perpendicular to the (002) and (111

Selected properties of Al_xZn_yO thin films prepared by reactive pulsed magnetron sputtering using a two-element Zn/Al target

• Witold Posadowski,
• Artur Wiatrowski,
• Jarosław Domaradzki and
• Michał Mazur

Beilstein J. Nanotechnol. 2022, 13, 344–354, doi:10.3762/bjnano.13.29

• was performed using the WTheiss Hard- and Software Scout software, ver. 4.17. X-ray diffraction in the grazing incidence mode (GIXRD) was used to assess the structural properties of the deposited thin films. For this purpose, an Empyrean PANalytical X-ray diffractometer equipped with a PIXel3D

Interfacial nanoarchitectonics for ZIF-8 membranes with enhanced gas separation

• Season S. Chen,
• Zhen-Jie Yang,
• Chia-Hao Chang,
• Hoong-Uei Koh,
• Sameerah I. Al-Saeedi,
• Kuo-Lun Tung and
• Kevin C.-W. Wu

Beilstein J. Nanotechnol. 2022, 13, 313–324, doi:10.3762/bjnano.13.26

• -ray diffraction were measured on a Rigaku Ultima IV with Cu Kα radiation (λ = 1.5418 Å) to check the crystallinity of the synthesized ZIF-8 thin films. The morphology of the supports, the free-standing thin films, and the supported membranes was observed by FE-SEM (NovaTM NanoSEM 230). The elemental

• membranes were synthesized according to the procedures described in the previous section with a reaction temperature of 80 °C and a reaction time of 12 h. Characterizations Pore size and porosity of α-Al2O3 disks were determined with a mercury porosimeter (AutoPore® IV 9520). Wide-angle patterns of powder X

Investigation of a memory effect in a Au/(Ti–Cu)Ox-gradient thin film/TiAlV structure

• Damian Wojcieszak,
• Jarosław Domaradzki,
• Michał Mazur,
• Tomasz Kotwica and
• Danuta Kaczmarek

Beilstein J. Nanotechnol. 2022, 13, 265–273, doi:10.3762/bjnano.13.21

• impurities were observed in the coating. Structural properties were analyzed using X-ray diffraction (XRD) and transmission electron microscopy (TEM). XRD patterns were obtained with a PANalytical Empyrean PIXed3D powder diffractometer with Cu Kα radiation (1.5406 Å) and no diffraction peaks were observed

Relationship between corrosion and nanoscale friction on a metallic glass

• Haoran Ma and
• Roland Bennewitz

Beilstein J. Nanotechnol. 2022, 13, 236–244, doi:10.3762/bjnano.13.18

• -spinning technique and provided by the Physics Institute at the University of Basel (Switzerland). The X-ray diffraction of Cu Kα radiation (XRD) verified the amorphous nature of the ribbons. All friction experiments were conducted at room temperature in 0.2 M phosphate buffer (Na2HPO4 + NaH2PO4, pH ≈ 7

Surfactant-free syntheses and pair distribution function analysis of osmium nanoparticles

• Mikkel Juelsholt,
• Jonathan Quinson,
• Emil T. S. Kjær,
• Baiyu Wang,
• Rebecca Pittkowski,
• Susan R. Cooper,
• Tiffany L. Kinnibrugh,
• Søren B. Simonsen,
• Luise Theil Kuhn,
• María Escudero-Escribano and
• Kirsten M. Ø. Jensen

Beilstein J. Nanotechnol. 2022, 13, 230–235, doi:10.3762/bjnano.13.17

• conditions to obtain Os NPs for further studies. Transmission electron microscopy images from samples synthesized with these parameter sets are shown in Figure 1. The small size of the nanoparticles challenges conventional structural characterization methods such as X-ray diffraction analysis (XRD). Here, we

Piezoelectric nanogenerator for bio-mechanical strain measurement

• Zafar Javed,
• Lybah Rafiq,
• Muhammad Anwaar Nazeer,
• Saqib Siddiqui,
• Muhammad Babar Ramzan,
• Muhammad Qamar Khan and
• Muhammad Salman Naeem

Beilstein J. Nanotechnol. 2022, 13, 192–200, doi:10.3762/bjnano.13.14

• characterized through scanning electron microscopy (SEM) and X-ray diffraction (XRD) to determine morphology and crystalline structure, respectively. Sensor development, its embedding, and testing The prepared PVDF nanofibrous mesh was folded into a square shape (4 cm2) with 2 mm thickness for sensor

• diameter variation of nanofibers against different solution concentrations (D). X-ray diffraction pattern of nanofibers at various concentrations. Digital oscilloscope graph of the sensor under low dynamic strain (A), the output voltage under low dynamic stress (B), digital oscilloscope graph of the sensor

• fluoride (PVDF) and other piezoelectric polymers are used in the form of fibers, filaments, and composites. In this research, PVDF nanofibers were developed and integrated onto a knitted fabric to fabricate a piezoelectric device for human body angle monitoring. Scanning electron microscopy and X-ray

Theranostic potential of self-luminescent branched polyethyleneimine-coated superparamagnetic iron oxide nanoparticles

• Rouhollah Khodadust,
• Ozlem Unal and
• Havva Yagci Acar

Beilstein J. Nanotechnol. 2022, 13, 82–95, doi:10.3762/bjnano.13.6

• , holds great potential for effective gene/drug delivery coupled with dual-mode imaging. a) TEM image of SPION@bPEI. b) AFM micrograph image of SPION@bPEI (magnetic mode). c) X-ray diffraction pattern of SPION@bPEI prepared via the in situ coating method. Since the presence of the polymer prevented the