Emerging strategies in the sustainable removal of antibiotics using semiconductor-based photocatalysts

• Yunus Ahmed,
• Keya Rani Dutta,
• Parul Akhtar,
• Md. Arif Hossen,
• Md. Jahangir Alam,
• Obaid A. Alharbi,
• Hamad AlMohamadi and
• Abdul Wahab Mohammad

Beilstein J. Nanotechnol. 2025, 16, 264–285, doi:10.3762/bjnano.16.21

• accomplished the separation with success, greatly enhancing the efficiency of the catalysts and their potential to be reused, while also decreasing the overall cost of synthesis. The construction of the α-Fe2O3@TiO2 photocatalyst resulted in a higher efficiency in removing the antibiotic cefixime (CFX) than

• that of pure TiO2 and Fe2O3 under visible light illumination (500 W halogen lamp and wavelengths above 400 nm) [72]. At a dosage of 0.012 g/L of α-Fe2O3@TiO2 and pH 4.76, 98.8% of an initial CFX concentration of 20.5 mg/L was effectively removed after 103 min. The heterojunction formed between TiO2 and

Electrospun one-dimensional nanostructures: a new horizon for gas sensing materials

• Muhammad Imran,
• Nunzio Motta and
• Mahnaz Shafiei

Beilstein J. Nanotechnol. 2018, 9, 2128–2170, doi:10.3762/bjnano.9.202

High photocatalytic activity of Fe₂O₃/TiO₂ nanocomposites prepared by photodeposition for degradation of 2,4-dichlorophenoxyacetic acid

• Shu Chin Lee,
• Hendrik O. Lintang and
• Leny Yuliati

Beilstein J. Nanotechnol. 2017, 8, 915–926, doi:10.3762/bjnano.8.93

• Puncak Tidar N-01, Malang 65151, East Java, Indonesia 10.3762/bjnano.8.93 Abstract Two series of Fe2O3/TiO2 samples were prepared via impregnation and photodeposition methods. The effect of preparation method on the properties and performance of Fe2O3/TiO2 for photocatalytic degradation of 2,4

• -dichlorophenoxyacetic acid (2,4-D) under UV light irradiation was examined. The Fe2O3/TiO2 nanocomposites prepared by impregnation showed lower activity than the unmodified TiO2, mainly due to lower specific surface area caused by heat treatment. On the other hand, the Fe2O3/TiO2 nanocomposites prepared by

• and TiO2 nanoparticles that improved charge transfer and suppressed electron–hole recombination. A further investigation on the role of the active species on Fe2O3/TiO2 confirmed that the crucial active species were both holes and superoxide radicals. The Fe2O3(0.5)/TiO2 sample also showed good

Photocatalysis applications of some hybrid polymeric composites incorporating TiO₂ nanoparticles and their combinations with SiO₂/Fe₂O₃

• Andreea Laura Chibac,
• Tinca Buruiana,
• Violeta Melinte and
• Emil C. Buruiana

Beilstein J. Nanotechnol. 2017, 8, 272–286, doi:10.3762/bjnano.8.30

• inorganic components (Si–O–Si or/and γ-Fe2O3) were prepared by the dispersion of premade NPs (nanocrystalline TiO2, TiO2/SiO2, TiO2/Fe2O3, TiO2/SiO2/Fe2O3) within a photopolymerizable urethane dimethacrylate (polytetrahydrofuran-urethane dimethacrylate, PTHF-UDMA). The physicochemical characterization of

• physicochemical characterization of nanoparticles Titania nanoparticles (TiO2) and titania nanoparticles mixed with Si–O–Si (TiO2/SiO2), γ-Fe2O3 (TiO2/Fe2O3) or Si–O–Si and γ-Fe2O3 (TiO2/SiO2/Fe2O3) were obtained by the sol–gel method, using titanium isopropoxide as precursor. The crystalline structures of the