Heat-induced transformation of nickel-coated polycrystalline diamond film studied in situ by XPS and NEXAFS

• Olga V. Sedelnikova,
• Yuliya V. Fedoseeva,
• Dmitriy V. Gorodetskiy,
• Yuri N. Palyanov,
• Elena V. Shlyakhova,
• Eugene A. Maksimovskiy,
• Anna A. Makarova,
• Lyubov G. Bulusheva and
• Aleksandr V. Okotrub

Beilstein J. Nanotechnol. 2025, 16, 887–898, doi:10.3762/bjnano.16.67

• the vacuum chamber for further SEM and Raman analysis under ambient conditions. Figure 4 shows SEM images of some large crystallites of about 100 μm in size on the surfaces of the annealed PCD and Ni-PCD. These crystallites have well-defined triangular (111) faces and truncated rectangular faces

Synchrotron X-ray photoelectron spectroscopy study of sodium adsorption on vertically arranged MoS₂ layers coated with pyrolytic carbon

• Alexander V. Okotrub,
• Anastasiya D. Fedorenko,
• Anna A. Makarova,
• Veronica S. Sulyaeva,
• Yuliya V. Fedoseeva and
• Lyubov G. Bulusheva

Beilstein J. Nanotechnol. 2025, 16, 847–859, doi:10.3762/bjnano.16.64

• then dried under ambient conditions. Morphology of sample surfaces was examined by SEM with a CIQTEK SEM5000 (CIQTEK Ltd., Hefei, Anhui, PRC) microscope at an accelerating voltage of 15 kV. The cross section of MoS2 film was prepared using a gallium-ion column FIB system and a two-stage protective cap

Synthesis and magnetic transitions of rare-earth-free Fe–Mn–Ni–Si-based compositionally complex alloys at bulk and nanoscale

• Shabbir Tahir,
• Tatiana Smoliarova,
• Carlos Doñate-Buendía,
• Michael Farle,
• Natalia Shkodich and
• Bilal Gökce

Beilstein J. Nanotechnol. 2025, 16, 823–836, doi:10.3762/bjnano.16.62

• carbon-supported TEM copper grid and dried under ambient conditions. The particle size distribution was determined by measuring the Feret diameter of individual particles from TEM images using ImageJ software [52]. The NP crystal structure was evaluated using CrysTBox software [53] using digital

Thickness dependent oxidation in CrCl₃: a scanning X-ray photoemission and Kelvin probe microscopies study

• Shafaq Kazim,
• Rahul Parmar,
• Maryam Azizinia,
• Matteo Amati,
• Muhammad Rauf,
• Andrea Di Cicco,
• Seyed Javid Rezvani,
• Dario Mastrippolito,
• Luca Ottaviano,
• Tomasz Klimczuk,
• Luca Gregoratti and
• Roberto Gunnella

Beilstein J. Nanotechnol. 2025, 16, 749–761, doi:10.3762/bjnano.16.58

• particular technological interest, even more in the case of chromium trihalides (CrX3, X = Cl, Br, and I), whose longer lifetime under ambient conditions is particularly intriguing. By using synchrotron-based scanning photoelectron microscopy with a resolution of 0.1 μm and Kelvin probe force microscopy, we

Electron beam-based direct writing of nanostructures using a palladium β-ketoesterate complex

• Chinmai Sai Jureddy,
• Krzysztof Maćkosz,
• Aleksandra Butrymowicz-Kubiak,
• Iwona B. Szymańska,
• Patrik Hoffmann and
• Ivo Utke

Beilstein J. Nanotechnol. 2025, 16, 530–539, doi:10.3762/bjnano.16.41

• introduced into the GIS under ambient conditions as it was tested stable. The GIS nozzle was placed 200 µm above the substrate at an angle of 30° to the substrate plane. Both GIS and substrate were heated using resistive heating wires. FEBID was carried out at an operating pressure of 2.0 × 10−6 mbar. For

Comparison of organic and inorganic hole transport layers in double perovskite material-based solar cell

• Deepika K and
• Arjun Singh

Beilstein J. Nanotechnol. 2025, 16, 119–127, doi:10.3762/bjnano.16.11

• passivation, efficiencies of 20.8% for Cs0.05(FA0.90MA0.10)0.95Pb(I0.90Br0.10)3, 18.9% for MAPbI3, and 18.7% for FAPbI3 perovskite layers were observed under ambient conditions and illumination for over 900 h. Mohammed et al. [9] optimized triple-cation PSCs that maintained 83% of the efficiency after 1600 h

• under ambient conditions with humidity levels of 35–40%. Here, 3,4-dihydroxyphenethylamine hydrochloride (3,4-DpACl) was used as an additive during perovskite fabrication. Despite significant research efforts, there are stability issues when working under critical environmental conditions, which is an

Characterization of ZnO nanoparticles synthesized using probiotic Lactiplantibacillus plantarum GP258

• Prashantkumar Siddappa Chakra,
• Aishwarya Banakar,
• Shriram Narayan Puranik,
• Vishwas Kaveeshwar,
• C. R. Ravikumar and
• Devaraja Gayathri

Beilstein J. Nanotechnol. 2025, 16, 78–89, doi:10.3762/bjnano.16.8

• ambient conditions with a bandgap and high exciton binding energy of 3.37 eV and −60 meV, respectively [10]. Because of this high exciton binding energy even at room temperature, the excitonic transitions have a broad range of applications such as in optics, gas detecting, piezoelectrics, and

Advanced atomic force microscopy techniques V

• Philipp Rahe,
• Ilko Bald,
• Nadine Hauptmann,
• Regina Hoffmann-Vogel,
• Harry Mönig and
• Michael Reichling

Beilstein J. Nanotechnol. 2025, 16, 54–56, doi:10.3762/bjnano.16.6

• . investigate the cross-sectional potential distribution across a III-V multilayer stack [6]. With a spatial resolution down to 20 nm at ambient conditions, they identified the presence of several space charge regions along the stack. The authors further conclude on future requirements on electrical contacts to

The effect of age on the attachment ability of stick insects (Phasmatodea)

• Marie Grote,
• Stanislav N. Gorb and
• Thies H. Büscher

Beilstein J. Nanotechnol. 2024, 15, 867–883, doi:10.3762/bjnano.15.72

• stock (Department for Functional Morphology and Biomechanics, Kiel University), kept under ambient conditions, and fed with fresh blackberry leaves ad libitum. This species was previously referred to as Sungaya inexpectata Zompro, 1996, until the original population of this widespread culture stock from

Exploring surface charge dynamics: implications for AFM height measurements in 2D materials

• Mario Navarro-Rodriguez,
• Andres M. Somoza and
• Elisa Palacios-Lidon

Beilstein J. Nanotechnol. 2024, 15, 767–780, doi:10.3762/bjnano.15.64

• [30]. This issue can be addressed with Kelvin probe force microscopy (KPFM). Under ambient conditions, the most common mode is amplitude modulation (AM-AFM), which uses the oscillation amplitude reduction as the input for the topography feedback. Its main aspects are summarized in [31]. At large free

• due to the removal of functionalities during the transition from GO to rGO. As mentioned above, in our AM-AFM measurements, the inconsistencies in height arise from the dissipative contrast between different materials. Under ambient conditions, this is typically dominated by capillary forces [39][40

Effect of repeating hydrothermal growth processes and rapid thermal annealing on CuO thin film properties

• Monika Ozga,
• Eunika Zielony,
• Aleksandra Wierzbicka,
• Anna Wolska,
• Marcin Klepka,
• Marek Godlewski,
• Bogdan J. Kowalski and
• Bartłomiej S. Witkowski

Beilstein J. Nanotechnol. 2024, 15, 743–754, doi:10.3762/bjnano.15.62

• performed under ambient conditions, which may have introduced surface states or absorbed water molecules on the surface of the investigated samples. Consequently, the obtained VCPD values and the resulting work function values are susceptible to additional errors, including those arising from the screening

• –Lorentzian functional GL(30) was applied during the simulations. Raman scattering measurements were performed under ambient conditions and room temperature using a T64000 Horiba Jobin-Yvon spectrometer configured in a backscattering geometry with a 1800 gr/mm grating and a microscope objective of 100

• gasses that may be absorbed at the surface [65]. The measured VCPD may considerably deviate from the real work function values as some of these factors influence the surface studied under ambient conditions. Nevertheless, because constant conditions were maintained for each of the analyzed samples, it is

Exfoliation of titanium nitride using a non-thermal plasma process

• Priscila Jussiane Zambiazi,
• Dolores Ribeiro Ricci Lazar,
• Larissa Otubo,
• Rodrigo Fernando Brambilla de Souza,
• Almir Oliveira Neto and
• Cecilia Chaves Guedes-Silva

Beilstein J. Nanotechnol. 2024, 15, 631–637, doi:10.3762/bjnano.15.53

• from graphene, prominent 2D vdW materials include hexagonal boron nitride, transition metal dichalcogenides, talc nanoflakes, and black phosphorus [2][3][4]. However, because of the inherent chemical stability of 2D vdW materials under ambient conditions, researchers have also turned their attention to

Aero-ZnS prepared by physical vapor transport on three-dimensional networks of sacrificial ZnO microtetrapods

• Veaceslav Ursaki,
• Tudor Braniste,
• Victor Zalamai,
• Emil Rusu,
• Vladimir Ciobanu,
• Vadim Morari,
• Daniel Podgornii,
• Pier Carlo Ricci,
• Rainer Adelung and
• Ion Tiginyanu

Beilstein J. Nanotechnol. 2024, 15, 490–499, doi:10.3762/bjnano.15.44

• processes, including those related to oxygen species adsorbed by the huge surface of the aeromaterial, as previously observed in ZnS nanostructures [42]. Some of these states may be related to oxygen vacancies and complex centers. Under ambient conditions, some oxygen species from the air are adsorbed at

Design, fabrication, and characterization of kinetic-inductive force sensors for scanning probe applications

• August K. Roos,
• Ermes Scarano,
• Elisabet K. Arvidsson,
• Erik Holmgren and
• David B. Haviland

Beilstein J. Nanotechnol. 2024, 15, 242–255, doi:10.3762/bjnano.15.23

• 60 chips from one wafer, detecting the thermal fluctuations at room temperature under ambient conditions and fitting them to a Lorentzian lineshape. We found that ωm decreases with the increasing radial distance D from the center of the wafer, as shown in Figure 7, probably because of non-uniform

A combined gas-phase dissociative ionization, dissociative electron attachment and deposition study on the potential FEBID precursor [Au(CH₃)₂Cl]₂

• Elif Bilgilisoy,
• Ali Kamali,
• Thomas Xaver Gentner,
• Gerd Ballmann,
• Sjoerd Harder,
• Hans-Peter Steinrück,
• Hubertus Marbach and
• Oddur Ingólfsson

Beilstein J. Nanotechnol. 2023, 14, 1178–1199, doi:10.3762/bjnano.14.98

• that we attribute to electron-induced secondary and tertiary reactions in the deposition process. We find this precursor to be stable at ambient conditions and to have sufficient vapor pressure to be suitable for use in HV instruments. More importantly, in the UHV setup, FEBID with [Au(CH3)2Cl]2

Dual-heterodyne Kelvin probe force microscopy

• Benjamin Grévin,
• Fatima Husainy,
• Dmitry Aldakov and
• Cyril Aumaître

Beilstein J. Nanotechnol. 2023, 14, 1068–1084, doi:10.3762/bjnano.14.88

• applications of KPFM are extremely broad. It is now used by physicists, chemists, and biologists to characterize the nanoscale electronic/electrostatic properties of an ever-expanding range of materials, interfaces, and devices, in ambient conditions, under ultrahigh vacuum, or at the liquid–substrate

• measurement, quantities that are directly proportional to the Fourier coefficients of the time-periodic surface photovoltage. Unfortunately, the translation of this promising technique from ambient conditions – where it has proven its worth – to ultra-high vacuum poses significant challenges. This is mainly

Silver-based SERS substrates fabricated using a 3D printed microfluidic device

• Phommachith Sonexai,
• Minh Van Nguyen,
• Bui The Huy and
• Yong-Ill Lee

Beilstein J. Nanotechnol. 2023, 14, 793–803, doi:10.3762/bjnano.14.65

• monolayer of Ag NPs appeared at the methanol/air interface. The PS@Ag substrates were created by depositing a monolayer of Ag NPs on the substrate surface after allowing the methanol to slowly evaporate under ambient conditions. SERS substrate characterization Raman spectra were obtained using a 24 mW laser

Cross-sectional Kelvin probe force microscopy on III–V epitaxial multilayer stacks: challenges and perspectives

• Mattia da Lisca,
• José Alvarez,
• James P. Connolly,
• Nicolas Vaissiere,
• Karim Mekhazni,
• Jean Decobert and
• Jean-Paul Kleider

Beilstein J. Nanotechnol. 2023, 14, 725–737, doi:10.3762/bjnano.14.59

• consisting of many layers and interfaces. The study and the comprehension of the mechanisms that take place at the interfaces is crucial for efficiency improvement. In this work, we apply frequency-modulated Kelvin probe force microscopy under ambient conditions to investigate the capability of this

• a study about the capability of cross-sectional KPFM for the study of a III–V multilayer stack under ambient conditions. In particular, we have investigated an InP/GaInAs(P) multilayer structure with layers of different widths and doping concentrations. The first objective of this analysis is the

• evaluation of the spatial resolution of our KPFM setup under ambient conditions. The second objective is a full understanding of the VCPD results combined with a description of the principal factors that affect KPFM measurements with the application of Kelvin probe (KP) numerical modelling. This enables the

Conjugated photothermal materials and structure design for solar steam generation

• Chia-Yang Lin and
• Tsuyoshi Michinobu

Beilstein J. Nanotechnol. 2023, 14, 454–466, doi:10.3762/bjnano.14.36

• , eventually resulting in APDA derivatives (Figure 8a). The formed APDA derivatives displayed a strong and broad absorption in the range of 500–1400 nm (Figure 8b). APDA was then combined with wood. It was coated on the surface of a wood piece and allowed to dry under ambient conditions. This simple process

Roll-to-roll fabrication of superhydrophobic pads covered with nanofur for the efficient clean-up of oil spills

• Patrick Weiser,
• Robin Kietz,
• Marc Schneider,
• Matthias Worgull and
• Hendrik Hölscher

Beilstein J. Nanotechnol. 2022, 13, 1228–1239, doi:10.3762/bjnano.13.102

• sandblasting step to obtain a sufficient hair density [28]. In particular, attention must be paid to the polymer residue left on the structuring roller (Figure 2c). If the residue polymer stays on the hot roller for too long, especially with oxygen present under ambient conditions, it might decompose and

Rapid fabrication of MgO@g-C₃N₄ heterojunctions for photocatalytic nitric oxide removal

• Minh-Thuan Pham,
• Duyen P. H. Tran,
• Xuan-Thanh Bui and
• Sheng-Jie You

Beilstein J. Nanotechnol. 2022, 13, 1141–1154, doi:10.3762/bjnano.13.96

• pollutants with light under ambient conditions [10]. Due to its unique properties, such as high chemical stability and low synthesis cost, graphitic carbon nitride has attracted considerable attention in the realm of environmental remediation [11][12][13]. It is an organic semiconductor that effectively

A cantilever-based, ultrahigh-vacuum, low-temperature scanning probe instrument for multidimensional scanning force microscopy

• Hao Liu,
• Zuned Ahmed,
• Sasa Vranjkovic,
• Manfred Parschau,
• Andrada-Oana Mandru and
• Hans J. Hug

Beilstein J. Nanotechnol. 2022, 13, 1120–1140, doi:10.3762/bjnano.13.95

• Cantilever-based atomic force microscopy (AFM) performed under ambient conditions has become an important tool to characterize new material systems as well as devices. Current instruments permit robust scanning over large areas, atomic-scale lateral resolution, and the characterization of various sample

• carried out under ambient conditions, are challenging to implement. In this article, we describe a cantilever-based low-temperature UHV AFM setup that allows one to transfer the versatile AFM techniques developed for ambient conditions to UHV and low-temperature conditions. We demonstrate that such a

• conditions are performed with tuning fork-based AFM, the vast majority of the AFM works performed under ambient conditions rely on microfabricated cantilevers that detect based on various mechanical properties and tips. Microfabricated cantilevers can be optimized for different AFM applications and

Theoretical investigations of oxygen vacancy effects in nickel-doped zirconia from ab initio XANES spectroscopy at the oxygen K-edge

• Dick Hartmann Douma,
• Lodvert Tchibota Poaty,
• Alessio Lamperti,
• Stéphane Kenmoe,
• Abdulrafiu Tunde Raji,
• Alberto Debernardi and
• Bernard M’Passi-Mabiala

Beilstein J. Nanotechnol. 2022, 13, 975–985, doi:10.3762/bjnano.13.85

• structure. The fluorite structure is not stable under ambient conditions and, thus, zirconia is usually found in the monoclinic phase. The cubic distorted fluorite structure may however be stabilized by a doping or by deposition as a thin film (because the surface energy of the cubic structure is lower than

Comparing the performance of single and multifrequency Kelvin probe force microscopy techniques in air and water

• Jason I. Kilpatrick,
• Emrullah Kargin and
• Brian J. Rodriguez

Beilstein J. Nanotechnol. 2022, 13, 922–943, doi:10.3762/bjnano.13.82

• environments. Appendix I: Calculation Parameters For calculation parameters see Table 2. Appendix II: Derivation of Performance Determining Equations The noise of a cantilever under ambient conditions at frequency ω, in a given bandwidth B, is defined as for the first two eigenmodes, where kB is Boltzmann's

Influence of thickness and morphology of MoS₂ on the performance of counter electrodes in dye-sensitized solar cells

• Lam Thuy Thi Mai,
• Hai Viet Le,
• Ngan Kim Thi Nguyen,
• Van La Tran Pham,
• Thu Anh Thi Nguyen,
• Nguyen Thanh Le Huynh and
• Hoang Thai Nguyen

Beilstein J. Nanotechnol. 2022, 13, 528–537, doi:10.3762/bjnano.13.44

• MoS2/FTO CEs. The stability of the devices was tested by repeating the I–V measurements every week (Supporting Information File 1, Figure S3). The PCE value of a DSSC fabricated using MoS2-1.25 showed a slight decrease of 2.6% and reached stability after two weeks of testing under ambient conditions