Simultaneous electrochemical determination of uric acid and hypoxanthine at a TiO₂/graphene quantum dot-modified electrode

• Vu Ngoc Hoang,
• Dang Thi Ngoc Hoa,
• Nguyen Quang Man,
• Le Vu Truong Son,
• Le Van Thanh Son,
• Vo Thang Nguyen,
• Le Thi Hong Phong,
• Ly Hoang Diem,
• Kieu Chan Ly,
• Ho Sy Thang and
• Dinh Quang Khieu

Beilstein J. Nanotechnol. 2024, 15, 719–732, doi:10.3762/bjnano.15.60

• solution, and acetic acid solution in appropriate ratios. To prepare a TiO2/GQDs-modified glassy carbon electrode (TiO2/GQDs-GCE), 5 mL of TiO2/GQDs suspension in water (0.1 mg/mL) was cast onto the surface of the bare GCE. The modified electrode was allowed to dry naturally for some hours at ambient

A graphene quantum dots–glassy carbon electrode-based electrochemical sensor for monitoring malathion

• Sanju Tanwar,
• Aditi Sharma and
• Dhirendra Mathur

Beilstein J. Nanotechnol. 2023, 14, 701–710, doi:10.3762/bjnano.14.56

• diffraction were used to characterize the morphological and structural properties of GQDs. An electrochemical sensor was developed by drop casting GQDs on a glassy carbon electrode (GCE). The sensor detects the organophosphate pesticide malathion in a selective and sensitive manner. Using cyclic voltammetry

• -functionalized nickel/silver/graphene quantum dot/graphene hybrid for the colorimetric detection of malathion [28]. This paper describes the development of an electrochemical sensor based on a graphene quantum dot-modified glassy carbon electrode (GQDs/GCE) for the determination and quantification of the

• organophosphate pesticide malathion. Graphene quantum dots were synthesized hydrothermally using glucose as precursor. The glassy carbon electrode that served as working electrode in the electrochemical cell was modified with graphene quantum dots by drop casting. To evaluate the modified electrode’s oxidation

Metal-organic framework-based nanomaterials as opto-electrochemical sensors for the detection of antibiotics and hormones: A review

• Akeem Adeyemi Oladipo,
• Saba Derakhshan Oskouei and
• Mustafa Gazi

Beilstein J. Nanotechnol. 2023, 14, 631–673, doi:10.3762/bjnano.14.52

• electrochemical sensor for the detection of tetracycline based on a glassy carbon electrode modified with MIL-53 (Fe) was published by Chen and co-workers [71]. The authors claim that the electrochemical sensor has a good linear relationship for tetracycline detection in the range of 0.0643–1.53 mol L−1 and that

Evaluation of electrosynthesized reduced graphene oxide–Ni/Fe/Co-based (oxy)hydroxide catalysts towards the oxygen evolution reaction

• Karolina Cysewska,
• Marcin Łapiński,
• Marcin Zając,
• Jakub Karczewski,
• Piotr Jasiński and
• Sebastian Molin

Beilstein J. Nanotechnol. 2023, 14, 420–433, doi:10.3762/bjnano.14.34

• and/or GO. For example, Wu et al. [13] chemically fabricated metal alloys and their oxides (NiCo, CoFe) with nitrogen-doped graphene (N-rGO/NiCo-NiO-CoO, N-rGO/CoFe-Co2FeO4) on a glassy carbon electrode (GCE). The N-rGO/NiCo-NiO-CoO and N-rGO/CoFe-Co2FeO4 catalysts revealed an OER overpotential (η) of

A nonenzymatic reduced graphene oxide-based nanosensor for parathion

• Sarani Sen,
• Anurag Roy,
• Ambarish Sanyal and
• Parukuttyamma Sujatha Devi

Beilstein J. Nanotechnol. 2022, 13, 730–744, doi:10.3762/bjnano.13.65

• at 3000 rpm for 15 min. The product (GO) was collected and dried at room temperature for further studies. Fabrication of electrochemically reduced graphene oxide modified electrodes Before surface modification of GO, a bare glassy carbon electrode (GCE, φ = 3 mm) was polished in 1.0, 0.3, and 0.05

• : Chemical sample table indicating corresponding CAS, supplier and other details. Table S2: Experimental sample table for composition analysis using binding energies of GO and RGO by XPS. Table S3: Experimental sample table for the modified glassy carbon electrode electrochemical characteristics. Figure S1

Morphology-driven gas sensing by fabricated fractals: A review

• Vishal Kamathe and
• Rupali Nagar

Beilstein J. Nanotechnol. 2021, 12, 1187–1208, doi:10.3762/bjnano.12.88

Exfoliation in a low boiling point solvent and electrochemical applications of MoO₃

• Matangi Sricharan,
• Bikesh Gupta,
• Sreejesh Moolayadukkam and
• H. S. S. Ramakrishna Matte

Beilstein J. Nanotechnol. 2020, 11, 662–670, doi:10.3762/bjnano.11.52

• Zetasizer NanoZS. All electrochemical measurements were carried out using Autolab PGSTAT302N. Electrode preparation and electrochemical testing Three-electrode system: A glassy carbon electrode (GCE, 0.3 cm diameter) as the working electrode, Pt wire as counter electrode and a saturated calomel electrode

Electrochemically derived functionalized graphene for bulk production of hydrogen peroxide

• Munaiah Yeddala,
• Pallavi Thakur,
• Anugraha A and
• Tharangattu N. Narayanan

Beilstein J. Nanotechnol. 2020, 11, 432–442, doi:10.3762/bjnano.11.34

• electrolyte concentration also determines the extent of functionalization of graphene. The presence of the C=O groups is further confirmed by cyclic voltammetry (CV) measurements in alkaline and acidic electrolyte. The CV profiles of the EEG samples (EEG-modified glassy carbon electrode (GCE) as the working

Simple synthesis of nanosheets of rGO and nitrogenated rGO

• Pallellappa Chithaiah,
• Madhan Mohan Raju,
• Giridhar U. Kulkarni and
• C. N. R. Rao

Beilstein J. Nanotechnol. 2020, 11, 68–75, doi:10.3762/bjnano.11.7

• of 4.0 mg rGO and 0.025 wt % (5 μL) of Nafion in 0.4 mL of dimethylformamide (DMF) was sonicated until a homogeneous dispersion was obtained. 3 μL catalyst ink was taken and drop-cast onto a glassy carbon electrode, which was allowed to dry at room temperature. A similar procedure was followed to

Synthesis of novel C-doped g-C₃N₄ nanosheets coupled with CdIn₂S₄ for enhanced photocatalytic hydrogen evolution

• Jingshuai Chen,
• Chang-Jie Mao,
• Helin Niu and
• Ji-Ming Song

Beilstein J. Nanotechnol. 2019, 10, 912–921, doi:10.3762/bjnano.10.92

• and a Pt wire was used as the counter electrode, respectively. The electrolyte was a 1 M Na2SO4 aqueous solution. A glassy carbon electrode containing the as-prepared sample served as the working electrode. Photocatalytic H2 production reaction In this work, the activity of the photocatalyst was

Electrodeposition of reduced graphene oxide with chitosan based on the coordination deposition method

• Mingyang Liu,
• Yanjun Chen,
• Chaoran Qin,
• Zheng Zhang,
• Shuai Ma,
• Xiuru Cai,
• Xueqian Li and
• Yifeng Wang

Beilstein J. Nanotechnol. 2018, 9, 1200–1210, doi:10.3762/bjnano.9.111

• et al. reported that after electrodeposition in the graphene oxide/chitosan solution, graphene nanosheets could be electrodeposited onto the glassy carbon electrode through the electrochemical reduction of graphene oxide [24]. However, it has been reported that the electrochemically reduced graphene

• film on a glassy carbon electrode (GCE) to detect 1-naphthol (as a model analyte) was explored. The electrochemical measurements were carried out using a three-electrode system with the GCE as the working electrode, a saturated calomel electrode as the reference electrode, and a platinum wire as the

• purchased from Nantong Green Biological Co., Ltd., China. The copper plates, silver plates, titanium plates, platinum foil, glassy carbon electrode and other chemicals were obtained from various commercial sources in China. All chemicals were of analytical grade and were not purified before use. Preparation

Synthesis and characterization of two new TiO₂-containing benzothiazole-based imine composites for organic device applications

• Anna Różycka,
• Agnieszka Iwan,
• Krzysztof Artur Bogdanowicz,
• Michal Filapek,
• Natalia Górska,
• Damian Pociecha,
• Marek Malinowski,
• Patryk Fryń,
• Agnieszka Hreniak,
• Jakub Rysz,
• Paweł Dąbczyński and
• Monika Marzec

Beilstein J. Nanotechnol. 2018, 9, 721–739, doi:10.3762/bjnano.9.67

• ], electrochemical measurements were carried out using an Eco Chemie Autolab PGSTAT128n potentiostat, glassy carbon electrode (diameter 2 mm), platinum coil and silver wire as working, auxiliary and reference electrodes, respectively. The potentials are referenced with respect to ferrocene (Fc), which was used as

Voltammetric determination of polyphenolic content in pomegranate juice using a poly(gallic acid)/multiwalled carbon nanotube modified electrode

• Refat Abdel-Hamid and
• Emad F. Newair

Beilstein J. Nanotechnol. 2016, 7, 1104–1112, doi:10.3762/bjnano.7.103

• Refat Abdel-Hamid Emad F. Newair Unit of Electrochemistry Applications (UEA), Chemistry Department, Faculty of Science, Sohag University, Sohag 82524, Egypt 10.3762/bjnano.7.103 Abstract A simple and sensitive poly(gallic acid)/multiwalled carbon nanotube modified glassy carbon electrode (PGA

• with thionine and nickel hexacyanoferrate [13]. A polyethyleneimine-functionalized graphene oxide modified glassy carbon electrode sensor was developed for sensitive detection of gallic acid [14]. A polyepinephrine modified glassy carbon electrode electrochemical sensor was developed for adsorptive

• stripping voltammetric determination of gallic acid and successfully applied for the estimation of GA in black tea [15]. The determination of gallic acid and caffeic acid was conducted by using a stable sensor based on a Zn–Al–NO3 layered double hydroxide film/glassy carbon electrode [16]. Recently

Fulleropeptide esters as potential self-assembled antioxidants

• Mira S. Bjelaković,
• Tatjana J. Kop,
• Jelena Đorđević and
• Dragana R. Milić

Beilstein J. Nanotechnol. 2015, 6, 1065–1071, doi:10.3762/bjnano.6.107

• potentiostat (CH Instruments, Austin, TX) by using a conventional three-electrode cell (5 cm3) equipped with a glassy carbon electrode, a silver wire (Ag/Ag+) (in contact with 0.01 M AgNO3 and 0.10 M TBAP in acetonitrile) and a platinum wire as the working, reference and auxiliary electrodes, respectively

Enhancement of photocatalytic H₂ evolution of eosin Y-sensitized reduced graphene oxide through a simple photoreaction

• Weiying Zhang,
• Yuexiang Li,
• Shaoqin Peng and
• Xiang Cai

Beilstein J. Nanotechnol. 2014, 5, 801–811, doi:10.3762/bjnano.5.92

• with a glassy carbon electrode (diameter 2 mm) as the working electrode, a platinum wire as the counter electrode, and an Ag/AgCl electrode as the reference electrode. The electrolyte was a solution of 0.1 M phosphate buffer solution (PBS, pH 7), 0.1 M KCl, 10 mM K3Fe(CN)6 and 10 mM K4Fe(CN)6

Electrospinning preparation and electrical and biological properties of ferrocene/poly(vinylpyrrolidone) composite nanofibers

• Ji-Hong Chai and
• Qing-Sheng Wu

Beilstein J. Nanotechnol. 2013, 4, 189–197, doi:10.3762/bjnano.4.19

• demonstrated that the morphologies and diameters of nanofibers could be controlled by adjusting the type of solvents and Fc concentration. These electrospun Fc/PVP nanofibers had bactericidal activity against the Gram-negative bacteria E. coli, and the glassy carbon electrode modified with Fc/PVP nanofibers

Glassy carbon electrodes modified with multiwalled carbon nanotubes for the determination of ascorbic acid by square-wave voltammetry

• Sushil Kumar and
• Victoria Vicente-Beckett

Beilstein J. Nanotechnol. 2012, 3, 388–396, doi:10.3762/bjnano.3.45

• carbon nanotubes were used to modify the surface of a glassy carbon electrode to enhance its electroactivity. Nafion served to immobilise the carbon nanotubes on the electrode surface. The modified electrode was used to develop an analytical method for the analysis of ascorbic acid (AA) by square-wave

• voltammetry (SWV). The oxidation of ascorbic acid at the modified glassy carbon electrode showed a peak potential at 315 mV, about 80 mV lower than that observed at the bare (unmodified) electrode. The peak current was about threefold higher than the response at the bare electrode. Replicate measurements of

• no significant difference (P = 0.05). Keywords: ascorbic acid; carbon nanotubes; glassy carbon electrode; square-wave voltammetry; Introduction L-ascorbic acid (AA), also known as vitamin C, is a well-known antioxidant, which helps the human body to reduce oxidative damage and protects food quality

Electrochemical behavior of dye-linked L-proline dehydrogenase on glassy carbon electrodes modified by multi-walled carbon nanotubes

• Haitao Zheng,
• Leyi Lin,
• Yosuke Okezaki,
• Ryushi Kawakami,
• Haruhiko Sakuraba,
• Toshihisa Ohshima,
• Keiichi Takagi and
• Shin-ichiro Suye

Beilstein J. Nanotechnol. 2010, 1, 135–141, doi:10.3762/bjnano.1.16

• , Institute of Genetic Resources, Faculty of Agriculture, Kyushu University, Fukuoka 812-8581, Japan Wakasa Wan Energy Research Center, Tsuruga 914-0192, Japan 10.3762/bjnano.1.16 Abstract A glassy carbon electrode (GC) was modified by multi-walled carbon nanotubes (MWCNTs). The modified electrode showed a

• ) was used to observe the surface of MWCNTs-modified electrode. All electrochemical experiments were performed on a potentiostat (CHI-800B, Austin, USA) connected to a personal computer. A typical three-electrode system was used, with a 3 mm diameter of glassy carbon electrode (GC) as the working