Green synthesis of carbon dot structures from Rheum Ribes and Schottky diode fabrication

• Muhammed Taha Durmus and
• Ebru Bozkurt

Beilstein J. Nanotechnol. 2024, 15, 1369–1375, doi:10.3762/bjnano.15.110

• nanostructures are obtained by using small nanoscale blocks. The hydrothermal synthesis method, which is a bottom-up method, is generally used in the synthesis of CDs. A very wide range of source materials, simple reaction equipment, and easy control of reaction conditions are the features that make this method

• switching speed and low forward voltage [14]. In this study, CDs were synthesized in a single step by hydrothermal synthesis using Rheum Ribes, a natural material, for the first time, and diodes were fabricated using the new CDs. To our knowledge, studies on diodes with CDs obtained from natural materials

• autoclave and hydrothermal synthesis was carried out at 125 °C for 12 h. After the reaction was completed, the aqueous suspension was brought to room temperature and filtered with ordinary filter paper. The filtrate was passed through a 0.22 µm membrane filter and centrifuged at 10000 rpm for 30 min. The

Green synthesis of biomass-derived carbon quantum dots for photocatalytic degradation of methylene blue

• Dalia Chávez-García,
• Mario Guzman,
• Viridiana Sanchez and
• Rubén D. Cadena-Nava

Beilstein J. Nanotechnol. 2024, 15, 755–766, doi:10.3762/bjnano.15.63

• photoluminescence spectroscopy (PL). The utilization of biomass as a carbon source offers great opportunities due to its abundance in nature and the wide range of sources available, which exhibit good luminescent and catalytic properties. Focusing on the hydrothermal synthesis method using biomass-derived

Radiofrequency enhances drug release from responsive nanoflowers for hepatocellular carcinoma therapy

• Yanyan Wen,
• Ningning Song,
• Yueyou Peng,
• Weiwei Wu,
• Qixiong Lin,
• Minjie Cui,
• Rongrong Li,
• Qiufeng Yu,
• Sixue Wu,
• Yongkang Liang,
• Wei Tian and
• Yanfeng Meng

Beilstein J. Nanotechnol. 2024, 15, 569–579, doi:10.3762/bjnano.15.49

• when combined with RF hyperthermia. Using these CUR-Fe@MnO2 NFs combined with RF, hyperthermia is a candidate method for the targeted treatment of HCC via combined chemotherapy/hyperthermia. Results and Discussion Characterization The Fe3O4 NCs were prepared by a microwave hydrothermal synthesis method

• Shanghai Zhongqiao Xinzhou Biotechnology Co., Ltd. (Shanghai, China). Preparation of Fe3O4 NCs Fe3O4 NCs were synthesized using a microwave hydrothermal synthesis method with a computer microwave ultrasonic synthesis/extraction instrument (XH-300A+, Beijing Xianghu Technology Development Co., Ltd., Beijing

Upscaling the urea method synthesis of CoAl layered double hydroxides

• Camilo Jaramillo-Hernández,
• Víctor Oestreicher,
• Martín Mizrahi and
• Gonzalo Abellán

Beilstein J. Nanotechnol. 2023, 14, 927–938, doi:10.3762/bjnano.14.76

• storage and conversion [19][20][21], quantum materials [22][23], and others [24]. This wide range of potential applications makes the development of reliable scaling processes crucial. Usually, LDHs are obtained by different synthesis procedures such as co-precipitation [25], hydrothermal synthesis [13

In situ magnesiothermic reduction synthesis of a Ge@C composite for high-performance lithium-ion batterie anodes

• Ha Tran Huu,
• Ngoc Phi Nguyen,
• Vuong Hoang Ngo,
• Huy Hoang Luc,
• Minh Kha Le,
• Minh Thu Nguyen,
• My Loan Phung Le,
• Hye Rim Kim,
• In Young Kim,
• Sung Jin Kim,
• Van Man Tran and
• Vien Vo

Beilstein J. Nanotechnol. 2023, 14, 751–761, doi:10.3762/bjnano.14.62

• with DI water and drying at 70 °C for 12 h, was denoted as Ge/C-iM750. An analogous route to our previous work [29] without adding activated carbon was applied to synthesize pure germanium (denoted as Ge). Hydrothermal coupling to synthesize Ge/C-HT180 composite The hydrothermal synthesis was carried

The microstrain-accompanied structural phase transition from h-MoO₃ to α-MoO₃ investigated by in situ X-ray diffraction

• Zeqian Zhang,
• Honglong Shi,
• Boxiang Zhuang,
• Minting Luo and
• Zhenfei Hu

Beilstein J. Nanotechnol. 2023, 14, 692–700, doi:10.3762/bjnano.14.55

• octahedron layers in the ⟨100⟩α direction, coupled by van der Waals interactions, and the octahedron layers stack in the ⟨010⟩α direction by shifting by a/2. Experimental Hydrothermal synthesis of h-MoO3 Molybdenum oxide h-MoO3 was synthesized by a traditional hydrothermal synthesis method. In a routine

Structural, optical, and bioimaging characterization of carbon quantum dots solvothermally synthesized from o-phenylenediamine

• Zoran M. Marković,
• Milica D. Budimir,
• Martin Danko,
• Dušan D. Milivojević,
• Pavel Kubat,
• Danica Z. Zmejkoski,
• Vladimir B. Pavlović,
• Marija M. Mojsin,
• Milena J. Stevanović and
• Biljana M. Todorović Marković

Beilstein J. Nanotechnol. 2023, 14, 165–174, doi:10.3762/bjnano.14.17

• only a minor role. Furthermore, during the hydrothermal synthesis of CQDs from o-phenylenediamine, the used precursor was able to form slowly a thermodynamically stable polyaniline and further conjugated sp2 domains with NH2 groups. Thus, the formed CQDs do not have reactive centers to generate singlet

Two-step single-reactor synthesis of oleic acid- or undecylenic acid-stabilized magnetic nanoparticles by thermal decomposition

• Mykhailo Nahorniak,
• Pamela Pasetto,
• Jean-Marc Greneche,
• Volodymyr Samaryk,
• Sandy Auguste,
• Anthony Rousseau,
• Nataliya Nosova and
• Serhii Varvarenko

Beilstein J. Nanotechnol. 2023, 14, 11–22, doi:10.3762/bjnano.14.2

• makes them ideal candidates for magnetic-assisted targeted drug delivery [12]. Nanoscale magnetite can be obtained through well-known synthesis routes, such as hydrothermal synthesis, thermal decomposition, or co-precipitation [10][11]. Each of these synthetic approaches has certain advantages and

Recent trends in Bi-based nanomaterials: challenges, fabrication, enhancement techniques, and environmental applications

• Vishal Dutta,
• Ankush Chauhan,
• Ritesh Verma,
• C. Gopalkrishnan and
• Van-Huy Nguyen

Beilstein J. Nanotechnol. 2022, 13, 1316–1336, doi:10.3762/bjnano.13.109

• considerations [52]. Bi-based photocatalysts may currently be synthesized using various methods, the most common of which are hydrothermal synthesis, solid-state reaction, and design and optimization. Today, NaBiO3·2H2O, Bi2O3, Bi(NO3)3·5H2O, BiCl3, and Bi are the most common Bi-based semiconductor

• increase in the overlap between Bi 6s and O 2p orbitals, a reduced charge transfer route, and strange floating features. In another approach, Huang et al. reported a one-step hydrothermal synthesis of a BiIO4/Bi2MoO6 hybrid photocatalyst for photodegradation of RhB dye [56]. Under visible-light irradiation

• simple hydrothermal synthesis for preparing 2D BiOCl nanosheets [83]. This was accomplished by altering the pH value of the precursor solution and using of dulcitol (C6H14O6) as surfactant. The pH value substantially influenced the thickness of the nanosheets and the fraction of exposed (001) facets. The

Enhanced electronic transport properties of Te roll-like nanostructures

• E. R. Viana,
• N. Cifuentes and
• J. C. González

Beilstein J. Nanotechnol. 2022, 13, 1284–1291, doi:10.3762/bjnano.13.106

• chemical composition of the nanostructures. This morphology has not been reported for the hydrothermal synthesis of Te nanostructures. Though, similar morphologies have been observed in Te scroll-like nanostructures grown by reflux processes [20] or Te shuttle-like scrolled nanostructures produced by amino

Recent advances in green carbon dots (2015–2022): synthesis, metal ion sensing, and biological applications

• Aisha Kanwal,
• Naheed Bibi,
• Sajjad Hyder,
• Arif Muhammad,
• Hao Ren,
• Jiangtao Liu and
• Zhongli Lei

Beilstein J. Nanotechnol. 2022, 13, 1068–1107, doi:10.3762/bjnano.13.93

• future applications in other disciplines [107]. Atchudan et al. reported a hydrothermal synthesis technique that yields CDs from Morus nigra (black mulberry) fruit juice [81]. This low-cost synthesis approach provides an effective, robust, and eco-friendly nanoscale sensor for the measurement of Fe3

• +. The CDs were also found to be appropriate FL probes for imaging human colon cancer (HTC-116) cells. Recently, Lin et al. proposed a unique antimicrobial compound for the preservation of Atlantic mackerel by synthesizing antimicrobial CDs through a hydrothermal synthesis approach using food materials

Nanoarchitectonics of the cathode to improve the reversibility of Li–O₂ batteries

• Hien Thi Thu Pham,
• Jonghyeok Yun,
• So Yeun Kim,
• Sang A Han,
• Jung Ho Kim,
• Jong-Won Lee and
• Min-Sik Park

Beilstein J. Nanotechnol. 2022, 13, 689–698, doi:10.3762/bjnano.13.61

• bimetallic ZIF–carbon/CNT composites has been thoroughly investigated for their practical use as potential cathode materials for high-performance LOBs. Results and Discussion In pursuit of improving the reversibility of LOBs, a bimetallic ZIF (ZnxCoy) was designed and grown on CNTs via hydrothermal synthesis

• cathode materials for high-performance LOBs. Experimental Material preparation In a manner similar to our previous works [12][41], bimetallic ZIFs (ZnxCoy) with various Zn/Co ratios were grown on CNTs via hydrothermal synthesis, where x/y was chosen to be 1/4, 1/1, and 4/1, respectively (corresponding to

Sodium doping in brookite TiO₂ enhances its photocatalytic activity

• Boxiang Zhuang,
• Honglong Shi,
• Honglei Zhang and
• Zeqian Zhang

Beilstein J. Nanotechnol. 2022, 13, 599–609, doi:10.3762/bjnano.13.52

• and solvents were used without further purification. Hydrothermal synthesis of the Na-doping brookite In a typical synthesis procedure, 1.27 g of oxalic acid dihydrate was dissolved into 50 mL of N,N-dimethylformamide (DMF) solvent to obtain a colorless and transparent solution under vigorous stirring

Influence of thickness and morphology of MoS₂ on the performance of counter electrodes in dye-sensitized solar cells

• Lam Thuy Thi Mai,
• Hai Viet Le,
• Ngan Kim Thi Nguyen,
• Van La Tran Pham,
• Thu Anh Thi Nguyen,
• Nguyen Thanh Le Huynh and
• Hoang Thai Nguyen

Beilstein J. Nanotechnol. 2022, 13, 528–537, doi:10.3762/bjnano.13.44

• investigated using various techniques such as chemical bath deposition [1], sputtering [2], hydrothermal synthesis [10][11][12][13], wet chemistry [14], thermal reduction [15], and electrodeposition (ED) [20]. Among these methods, ED shows many advances thank to its simplicity and rapidity. Additionally, it

Zinc oxide nanostructures for fluorescence and Raman signal enhancement: a review

• Ioana Marica,
• Fran Nekvapil,
• Maria Ștefan,
• Cosmin Farcău and
• Alexandra Falamaș

Beilstein J. Nanotechnol. 2022, 13, 472–490, doi:10.3762/bjnano.13.40

• conditions involved in the hydrothermal synthesis of ZnO make it an attractive growth method, widely used in recent years. A comprehensive review indicating the morphology of ZnO nanostructures grown using this method is given in [30]. Successful examples of ordered ZnO nanorods [6], one of most common ZnO

• controlled method. ZnO nanorods were first grown and the rod surface was then decorated with Au NPs, resulting in ZnO nanorods with an average diameter of 300 nm and spherical Au NPs with sizes between 5 and 10 nm [46]. ZnO nanorod arrays were obtained by hydrothermal synthesis and then Ag NPs were deposited

A non-enzymatic electrochemical hydrogen peroxide sensor based on copper oxide nanostructures

• Irena Mihailova,
• Vjaceslavs Gerbreders,
• Marina Krasovska,
• Eriks Sledevskis,
• Valdis Mizers,
• Andrejs Bulanovs and
• Andrejs Ogurcovs

Beilstein J. Nanotechnol. 2022, 13, 424–436, doi:10.3762/bjnano.13.35

• , such as thermal oxidation of copper electrodes in an oxygen atmosphere [72][73], hydrothermal chemical oxidation of copper surfaces [56], and hydrothermal synthesis using various precursors containing copper ions [74][75]. Copper oxide nanostructures can also be obtained as a powder and then applied to

• detection of H2O2. The article proves the higher efficiency of nanostructured electrodes compared to electrodes with less developed surface. The article shows the influence of the time of hydrothermal synthesis on the morphology of nanostructures and, as a result, the change in the sensitivity of the sensor

• (reduction of the current peak in the CV curves). An increase in the duration of hydrothermal synthesis to 6 h also leads to a change in the morphology of the nanostructures. The SEM picture shows that the nanoleaves grow together, forming dense spherical formations that are difficult for the solution to

Morphology-driven gas sensing by fabricated fractals: A review

• Vishal Kamathe and
• Rupali Nagar

Beilstein J. Nanotechnol. 2021, 12, 1187–1208, doi:10.3762/bjnano.12.88

• had minimum influence. Thus, better interaction between NO2 and the sensor surface was achieved. The SnO2 DNWs were estimated to have a fractal dimension of 1.82. In 2017, Zang et al. fabricated SnO2 leaf-like hierarchical structures by hydrothermal synthesis [67]. Figure 7a–f shows SEM images of SnO2

One-step synthesis of carbon-supported electrocatalysts

• Sebastian Tigges,
• Nicolas Wöhrl,
• Ivan Radev,
• Ulrich Hagemann,
• Markus Heidelmann,
• Thai Binh Nguyen,
• Stanislav Gorelkov,
• Stephan Schulz and
• Axel Lorke

Beilstein J. Nanotechnol. 2020, 11, 1419–1431, doi:10.3762/bjnano.11.126

• as solvothermal and hydrothermal synthesis [9]. In these processes, long ultrasonication as well as reduction/heating procedures are required [6][10], both of which will impede industrial production. In contrast, physical approaches for the synthesis of electrocatalysts (such as plasma-assisted

Gas sorption porosimetry for the evaluation of hard carbons as anodes for Li- and Na-ion batteries

• Yuko Matsukawa,
• Fabian Linsenmann,
• Maximilian A. Plass,
• George Hasegawa,
• Katsuro Hayashi and
• Tim-Patrick Fellinger

Beilstein J. Nanotechnol. 2020, 11, 1217–1229, doi:10.3762/bjnano.11.106

• ]. The first step was a hydrothermal synthesis of a precursor, followed by a pyrolytic carbonization to get the final HC product. At first, a 25 wt % solution of ᴅ-fructose (Sigma-Aldrich, Germany) in deionized water (Millipore, Merck, Germany) was prepared. Similar to a synthesis reported by Fellinger

High permittivity, breakdown strength, and energy storage density of polythiophene-encapsulated BaTiO₃ nanoparticles

• Adnanullah Khan,
• Amir Habib and
• Adeel Afzal

Beilstein J. Nanotechnol. 2020, 11, 1190–1197, doi:10.3762/bjnano.11.103

• dioxide (TiO2 Tronox, 99.5%, Tronox Pigments GmbH) are used as Ba and Ti precursors for the hydrothermal synthesis of BTO nanoparticles. Ba(OH)2·8H2O also acts as the mineralizer and prevents the use of NaOH or KOH for controlling the pH value of the reaction mixture [12]. Equimolar amounts of Ba and Ti

Preparation, characterization and photocatalytic performance of heterostructured CuO–ZnO-loaded composite nanofiber membranes

• Wei Fang,
• Liang Yu and
• Lan Xu

Beilstein J. Nanotechnol. 2020, 11, 631–650, doi:10.3762/bjnano.11.50

• environmental monitoring, industry, aviation, and transportation. In this paper, heterostructured CuO–ZnO-loaded CNF membranes (CNFMs) were prepared successfully by a combination of electrospinning, heat treatment, and hydrothermal synthesis. The influence of the synthesis parameters on morphology, structure

• three times, and the degradation rate remained above 90%. Keywords: electrospinning; composite nanofibers; heterostructured CuO–ZnO; hydrothermal synthesis; photocatalysis; semiconductor oxide; Introduction Water remediation is one of the main scientific research subjects regarding environmental

• work [37], bubble-electrospinning was used to prepare Cu(Ac)2/Zn(Ac)2/PVDF/PAN on a large scale. Subsequently, PVDF/PAN CNFMs loaded with CuO and ZnO nanocrystals were prepared using heat treatment and hydrothermal synthesis. However, the diameter distribution of CNFMs obtained by bubble

Simple synthesis of nanosheets of rGO and nitrogenated rGO

• Pallellappa Chithaiah,
• Madhan Mohan Raju,
• Giridhar U. Kulkarni and
• C. N. R. Rao

Beilstein J. Nanotechnol. 2020, 11, 68–75, doi:10.3762/bjnano.11.7

• ], solvothermal [16], hydrothermal synthesis [17], laser reduction of graphite oxide [18][19], and photo thermal deoxygenation of graphene oxide by camera flash have been developed to reduce the oxygen content of GO in order to restore the conjugated network [20]. Recently, a well-known chemical reduction method

Design and facile synthesis of defect-rich C-MoS₂/rGO nanosheets for enhanced lithium–sulfur battery performance

• Chengxiang Tian,
• Juwei Wu,
• Zheng Ma,
• Bo Li,
• Pengcheng Li,
• Xiaotao Zu and
• Xia Xiang

Beilstein J. Nanotechnol. 2019, 10, 2251–2260, doi:10.3762/bjnano.10.217

• are almost completely removed during the hydrothermal synthesis and annealing process [41]. Full nitrogen sorption isotherms of the composites were measured to obtain the specific surface area and the pore size distribution. A type-IV isotherm with a type-H3 hysteresis loop in the relative pressure

Synthesis of highly active ETS-10-based titanosilicate for heterogeneously catalyzed transesterification of triglycerides

• Muhammad A. Zaheer,
• David Poppitz,
• Khavar Feyzullayeva,
• Marianne Wenzel,
• Jörg Matysik,
• Radomir Ljupkovic,
• Aleksandra Zarubica,
• Alexander A. Karavaev,
• Andreas Pöppl,
• Roger Gläser and
• Muslim Dvoyashkin

Beilstein J. Nanotechnol. 2019, 10, 2039–2061, doi:10.3762/bjnano.10.200

• initial reaction rates are needed. Conclusion The applied hydrothermal synthesis of the microporous ETS-10 titanosilicate (Na,K-ETS-10) resulted in crystals with an average size of ≈30 μm without structural defects visible by SEM and TEM, but with the presence of a small fraction (less than 5%) of

• 5 t. Afterwards, the pellets were ground and sieved in order to obtain fractions between 1.0 and 1.5 μm. Preparation of ETS-10-based catalysts ETS-10 molecular sieves were prepared by hydrothermal synthesis following a reported procedure [32]. Initially, a visually transparent silica-containing

An efficient electrode material for high performance solid-state hybrid supercapacitors based on a Cu/CuO/porous carbon nanofiber/TiO₂ hybrid composite

• Mamta Sham Lal,
• Thirugnanam Lavanya and
• Sundara Ramaprabhu

Beilstein J. Nanotechnol. 2019, 10, 781–793, doi:10.3762/bjnano.10.78

• on the surface were transform to CuO nanoparticles during hydrothermal synthesis, but in bulk of fiber, retained the phase of Cu. Raman spectroscopy was used to estimate a crystalline phase and the degree of graphitization of the subsequent synthesized samples (Figure 4a). CNF exhibited two