Quantification of lead through rod-shaped silver-doped zinc oxide nanoparticles using an electrochemical approach

• Ravinder Lamba,
• Gaurav Bhanjana,
• Neeraj Dilbaghi,
• Vivek Gupta and
• Sandeep Kumar

Beilstein J. Nanotechnol. 2025, 16, 422–434, doi:10.3762/bjnano.16.33

• lead sensor had a high sensitivity of 16 µA·ppm−1·cm−2, along with a detection limit of 3 ppm. Additionally, it demonstrated a response time of less than 2 s. This sensor is most suitable for applications that necessitate cost-effectiveness, rapid readings, and data collection in the field or at the

Engineered PEG–PCL nanoparticles enable sensitive and selective detection of sodium dodecyl sulfate: a qualitative and quantitative analysis

• Soni Prajapati and
• Ranjana Singh

Beilstein J. Nanotechnol. 2025, 16, 385–396, doi:10.3762/bjnano.16.29

• –PCL NPs-based detection system was compared with other nanoparticle-based detection methods for SDS, as summarized in Table 1. This comparison highlights the advantages of the present work, including its high specificity, rapid response time, and ability to effectively operate in complex matrices

Out-of-plane polarization induces a picosecond photoresponse in rhombohedral stacked bilayer WSe₂

• Guixian Liu,
• Yufan Wang,
• Zhoujuan Xu,
• Zhouxiaosong Zeng,
• Lanyu Huang,
• Cuihuan Ge and
• Xiao Wang

Beilstein J. Nanotechnol. 2024, 15, 1362–1368, doi:10.3762/bjnano.15.109

• intrinsic photoresponse time of approximately 3 ps. The ultrafast response time remains consistent across varying detection powers, demonstrating environmental stability and highlighting the potential in optoelectronic applications. Our study presents an effective strategy for enhancing the response time of

• scanning photocurrent map under zero bias. In addition, the OOP polarization accelerates the drift of photogenerated carriers, giving the heterojunction region an ultrafast intrinsic response time of approximately 3 ps, surpassing that of graphene under the same conditions. Despite variations in probe

• power, the ultrafast response time remains consistent, highlighting the reliability of the high-speed heterojunction photodetector across different conditions, confirming its potential application in the field of optoelectronics. Our findings enhance the comprehension of the impact of polarization on

Investigation of Hf/Ti bilayers for the development of transition-edge sensor microcalorimeters

• Victoria Y. Safonova,
• Anna V. Gordeeva,
• Anton V. Blagodatkin,
• Dmitry A. Pimanov,
• Anton A. Yablokov and
• Andrey L. Pankratov

Beilstein J. Nanotechnol. 2024, 15, 1353–1361, doi:10.3762/bjnano.15.108

• generally also means a shorter thermal response time, allowing the detector to respond more quickly to small temperature changes. Second, the active area is reduced, which allows for a more efficient detection of a useful signal because of the higher energy density and, therefore, a higher signal-to-noise

Bolometric IR photoresponse based on a 3D micro-nano integrated CNT architecture

• Yasameen Al-Mafrachi,
• Sandeep Yadav,
• Sascha Preu,
• Jörg J. Schneider and
• Oktay Yilmazoglu

Beilstein J. Nanotechnol. 2024, 15, 1030–1040, doi:10.3762/bjnano.15.84

• response to IR (980 nm) absorption for a 20 × 20 μm2 device. The device exhibits an exceptionally fast response time of ≈0.15 ms, coupled with a TCR of −0.91 %/K. These attributes underscore its high operating speed and responsivity, respectively. In particular, the device maintains excellent thermal

• ], increased responsivity, unwavering reliability, ultrafast response time, and a substantial reduction in device size. The introduction of large, two-dimensional (2D) detector arrays has further increased the complexity of the detector optimization. In response to these multifaceted challenges and the quest

• contacts. The lateral and vertical dimensions of the M-shaped CNT architecture can be adjusted independently to achieve low thermal conductivity, high lateral resistance, and small response time to achieve a higher bolometric effect. Our first responsivity measurements with similar CNT wall structures were

Ultrasensitive and ultrastretchable metal crack strain sensor based on helical polydimethylsiloxane

• Shangbi Chen,
• Dewen Liu,
• Weiwei Chen,
• Huajiang Chen,
• Jiawei Li and
• Jinfang Wang

Beilstein J. Nanotechnol. 2024, 15, 270–278, doi:10.3762/bjnano.15.25

• substrate via sputter deposition. The metal thin film is then pre-stretched to generate microcracks. The sensor demonstrates a remarkable stretchability of 300%, an exceptional sensitivity with a maximum gauge factor reaching 107, a rapid response time of 158 ms, minimal hysteresis, and outstanding

• gauge factor of 107, a broad strain range of 300%, a rapid response time of 158 ms, minimal hysteresis, and outstanding durability. (The GF serves as a means to assess the sensitivity of stretchable strain sensors; it is defined as the ratio of the relative change in resistance to the applied mechanical

• remarkable stability and favorable recoverability. Figure 2d illustrates the response time of the helical sensor when subjected to a quasi-transient step strain of 10%. Notably, the response time was approximately 158 ms, while the relaxation time was approximately 243 ms, indicating a strong response to

Enhanced feedback performance in off-resonance AFM modes through pulse train sampling

• Mustafa Kangül,
• Navid Asmari,
• Santiago H. Andany,
• Marcos Penedo and
• Georg E. Fantner

Beilstein J. Nanotechnol. 2024, 15, 134–143, doi:10.3762/bjnano.15.13

• response time of the Z piezo. The width of the interaction window determines the number of closed-loop control iterations within a single ORT cycle. A wider interaction window allows for more iterations, potentially improving the tracking quality. The width of the interaction window is influenced by the

A visible-light photodetector based on heterojunctions between CuO nanoparticles and ZnO nanorods

• Doan Nhat Giang,
• Nhat Minh Nguyen,
• Duc Anh Ngo,
• Thanh Trang Tran,
• Le Thai Duy,
• Cong Khanh Tran,
• Thi Thanh Van Tran,
• Phan Phuong Ha La and
• Vinh Quang Dang

Beilstein J. Nanotechnol. 2023, 14, 1018–1027, doi:10.3762/bjnano.14.84

• , increasing the visible-light intensity promotes more excited electrons in the conduction band (CB) of CuO NPs. These electrons transfer to the CB of ZnO NRs and increase the photocurrent collected by the Ag electrodes. Response time and recovery are essential when evaluating a photodetector’s performance

• . The response time is defined as the time to approach 63% of the maximum recorded photocurrent, while the recovery time is the time to decay to 37% of the highest value of the photodetector [46]. Under the 395 nm light illumination, response time and recovery time are estimated at about 21.38 s and

• maximum values of R, G, and D were 1.38 A·W−1, 4.33, and 2.58 × 1011 Jones, respectively. The recovery time was 84.64 s, while the response time was about 21.38 s to achieve 63% of the maximum photocurrent value. Simultaneously, the CuO NPs/ZnO NRs photodetector shows photoresponse to other visible

A graphene quantum dots–glassy carbon electrode-based electrochemical sensor for monitoring malathion

• Sanju Tanwar,
• Aditi Sharma and
• Dhirendra Mathur

Beilstein J. Nanotechnol. 2023, 14, 701–710, doi:10.3762/bjnano.14.56

• use of graphene and its derivatives is widespread for electrochemical detection since 2D graphene sheets provide numerous electrochemical sites for the detection of target molecules, while electrons in the sp2-hybridized pz orbital have a faster electron transfer rate, which enhances response time and

Metal-organic framework-based nanomaterials as opto-electrochemical sensors for the detection of antibiotics and hormones: A review

• Akeem Adeyemi Oladipo,
• Saba Derakhshan Oskouei and
• Mustafa Gazi

Beilstein J. Nanotechnol. 2023, 14, 631–673, doi:10.3762/bjnano.14.52

• and challenges It is crucial to assess the performance of sensors during development using standard metrics such as selectivity, sensitivity, the limit of detection (LOD), and response time. Selectivity refers to a sensor’s capacity to respond to a narrow range of target analytes while resisting

• are correlated with sensor response time. An ideal sensor, when taking into account the aforementioned key parameters, should be specific for the target analytes, sensitive to changes in analyte concentrations, have a rapid response time, have a long lifespan of at least several months, and be small

Characterisation of a micrometer-scale active plasmonic element by means of complementary computational and experimental methods

• Ciarán Barron,
• Giulia Di Fazio,
• Samuel Kenny,
• Silas O’Toole,
• Robin O’Reilly and
• Dominic Zerulla

Beilstein J. Nanotechnol. 2023, 14, 110–122, doi:10.3762/bjnano.14.12

• case to ensure the probe captured the deflection due to thermal expansion while minimising artifacts caused by the periodic potential on the surface. The sample was driven with a frequency of 1227 Hz, well below the 170 kHz limitation on the response time of the z-piezo control of the scanner in the

Efficient liquid exfoliation of KP₁₅ nanowires aided by Hansen's empirical theory

• Zhaoxuan Huang,
• Zhikang Jiang,
• Nan Tian,
• Disheng Yao,
• Fei Long,
• Yanhan Yang and
• Danmin Liu

Beilstein J. Nanotechnol. 2022, 13, 788–795, doi:10.3762/bjnano.13.69

• one-dimensional material with high carrier mobility (308 cm2·V−1·s−1) and rapid response time [8][9][10]. These one-dimensional materials are ideal for photovoltaic and photocatalytic applications. The KP15 is considered to be a novel low-dimensional material with layered structure, high hole carrier

• mobility (1000 cm2·V−1·s−1), and highly anisotropic properties [11]. The photodetectors prepared with KP15 have a fast response time and are ideal materials for photovoltaic applications [12]. Based on our previous studies, KP15 is also a one-dimensional material with a defect-free surface [13][14]. This

A nonenzymatic reduced graphene oxide-based nanosensor for parathion

• Sarani Sen,
• Anurag Roy,
• Ambarish Sanyal and
• Parukuttyamma Sujatha Devi

Beilstein J. Nanotechnol. 2022, 13, 730–744, doi:10.3762/bjnano.13.65

• performed to achieve excellent nanosensor performance, such as higher sensitivity, low detection limit (10.9 pM), linear response range (3 × 10−11–11 × 10−6 M), and fast response time. The proposed ERGO/GCE nanosensor exhibits excellent electrocatalytic activity, long-term storage stability, reproducibility

Direct measurement of surface photovoltage by AC bias Kelvin probe force microscopy

• Masato Miyazaki,
• Yasuhiro Sugawara and
• Yan Jun Li

Beilstein J. Nanotechnol. 2022, 13, 712–720, doi:10.3762/bjnano.13.63

• energy resolutions and the image acquisition time of AC-KPFM in the AM mode are comparable to those of the classical KPFM in the AM mode, because both methods detect the electrostatic force, and the response time of the bias feedback τ limits the image acquisition time. To reach sufficient sensitivity

• classical KPFM. The spatial and energy resolutions and the image acquisition time of AC-KPFM in the FM mode are comparable to those of the classical KPFM in the FM mode, because both methods detect the electrostatic force gradient and the response time of the bias feedback τ limits their image acquisition

• disappeared in the spectrum of Δf (Figure 2b). Here, we cannot determine the polarity of the SPV because the phase for the lock-in amplifier was adjusted to maximize the absolute value of the demodulated output. We note that the response time of SPV on the rutile TiO2(110) surface is intrinsically

Approaching microwave photon sensitivity with Al Josephson junctions

• Andrey L. Pankratov,
• Anna V. Gordeeva,
• Leonid S. Revin,
• Dmitry A. Ladeynov,
• Anton A. Yablokov and
• Leonid S. Kuzmin

Beilstein J. Nanotechnol. 2022, 13, 582–589, doi:10.3762/bjnano.13.50

• without a photon, and q[1], q[2], q[3], … are the detection efficiencies for one, two, three, … photons, respectively. The slope of the fitting curves is set by the number of photons, triggering the switching. The position on the power axis is determined by the effective system response time δt and by the

Electrostatic pull-in application in flexible devices: A review

• Teng Cai,
• Yuming Fang,
• Yingli Fang,
• Ruozhou Li,
• Ying Yu and
• Mingyang Huang

Beilstein J. Nanotechnol. 2022, 13, 390–403, doi:10.3762/bjnano.13.32

• between the two plates, ε0 is the vacuum permittivity, and A is the area of the two plates. It can be seen from Equation 1 that the material, size, and structure of the electrodes affect properties such as voltage, response time, and life cycles. When designing an ideal MEMS device, these parameters

• , Kaul et al. [15][16] prepared a two-terminal SWCNT NEM switch. The response time of the switch is nanoseconds, and the voltage is 3.5–4.5 V. Cha et al. [21] prepared a multiwalled carbon nanotube (MWCNT) NEM switch. The switch length is 800 nm, the diameter is 20–40 nm, the initial gap is 40–60 nm, and

• et al. [8] made a CuO NWs switch, 3 µm long, 80 nm in diameter, and 120 nm in the gap, with a pull-in voltage of 12.5 V. Feng et al. [40] prepared SiC nanowire NEM switches using bottom-up techniques. The pull-in voltage ranges from one to several volts and the response time is below microseconds

A photonic crystal material for the online detection of nonpolar hydrocarbon vapors

• Evgenii S. Bolshakov,
• Aleksander V. Ivanov,
• Andrei A. Kozlov,
• Anton S. Aksenov,
• Elena V. Isanbaeva,
• Sergei E. Kushnir,
• Aleksei D. Yapryntsev,
• Aleksander E. Baranchikov and
• Yury A. Zolotov

Beilstein J. Nanotechnol. 2022, 13, 127–136, doi:10.3762/bjnano.13.9

• as a more contrasting color change of the sensor matrix. The effect of vapors of nonpolar aliphatic organic solvents, in contrast, leads to an instantaneous photonic bandgap shift, but there is no sharp jump in the kinetic curve. The response time means the moment when the PBG shift rate is maximum

• screened for the color change time of the sensor. For the series benzene, toluene, p-xylene and n-pentane, n-heptane, n-octane and n-decane, an increase in the response time is observed that is close to exponential. This allows for the detection of the total toxic effect considering the different

• temperature was maintained at 23.1–23.6 °C) and (b) differential curves plotted from the average experimental data (additional curves are given for n-heptane and n-octane). Response rates of sensor matrices (red) and vapor pressure (blue): (a) response time for aromatic hydrocarbons (matrix thickness about

Morphology-driven gas sensing by fabricated fractals: A review

• Vishal Kamathe and
• Rupali Nagar

Beilstein J. Nanotechnol. 2021, 12, 1187–1208, doi:10.3762/bjnano.12.88

• to be possessing better gas sensing capabilities. Fab-fracs with these salient features will help in designing the commercial gas sensors with better performance. Keywords: adsorption sites; fabricated fractal; fractal dimension; gas sensor; morphology; pore network; recovery time; response time

• responds in a particular environment with time), the response time (time taken by a sensor to detect no gas to 90% of the gas when exposed to a gas environment), and recovery time (time taken by a sensor to fall to 10% of its baseline resistance value when the gas is removed from the environment

• performed by Kante et al. were in the temperature range of 200–300 °C. For CO, the response was observed to be about 2.5 at 250 °C with a response time of 70 s and a recovery time of 30 s. When exposed to ethanol vapor, the resulting film exhibited a higher sensitivity (400% at 227 °C) towards ethanol with

Open-loop amplitude-modulation Kelvin probe force microscopy operated in single-pass PeakForce tapping mode

• Gheorghe Stan and
• Pradeep Namboodiri

Beilstein J. Nanotechnol. 2021, 12, 1115–1126, doi:10.3762/bjnano.12.83

• data is limited. Moreover, the finite response time of the CL feedback (of the order of milliseconds in some cases) prevents the use of CL KPFM from observing fast electrodynamic processes. Some of these impediments are addressed in OL implementations such as time-resolved electrostatic force

Uniform arrays of gold nanoelectrodes with tuneable recess depth

• Elena O. Gordeeva,
• Ilya V. Roslyakov,
• Alexey P. Leontiev,
• Alexey A. Klimenko and
• Kirill S. Napolskii

Beilstein J. Nanotechnol. 2021, 12, 957–964, doi:10.3762/bjnano.12.72

• value was chosen as an optimal Ed for further experiments. According to the scheme of the NEA fabrication (Figure 1), the first Cu segment’s length (LCu1) determines the recess of NEAs relative to the template surface. In order to enhance a response time of sensing material inside AAO, LCu1 was

Nickel nanoparticle-decorated reduced graphene oxide/WO₃ nanocomposite – a promising candidate for gas sensing

• Ilka Simon,
• Alexandr Savitsky,
• Rolf Mülhaupt,
• Vladimir Pankov and
• Christoph Janiak

Beilstein J. Nanotechnol. 2021, 12, 343–353, doi:10.3762/bjnano.12.28

• /WO3 composite and CO gas, a response time (Tres) of 7 min and a recovery time (Trec) of 2 min was determined. Keywords: gas sensing; magnetic measurements; nickel nanoparticles; reduced graphene oxide; tungsten oxide; Introduction Toxic gases as well as volatile organic compounds (VOC) are known air

• of resistance in n-type MOS and an increase of resistance in p-type MOS and vice versa [8]. MOS have certain advantages such as fast response time and excellent sensitivity towards all kinds of gases [11]. The major disadvantages of MOS are their poor selectivity and high operating temperatures of

• the sensitivity, response time and working temperature of MOS/rGO systems [15][41]. TiO2/rGO decorated with Pd and Pt nanoparticles was successfully used in the gas sensing of hydrogen gas [19]. The decoration of WO3/rGO nanosheets with Pt nanoparticles yielded a faster response for acetone at 200 °C

A self-powered, flexible ultra-thin Si/ZnO nanowire photodetector as full-spectrum optical sensor and pyroelectric nanogenerator

• Liang Chen,
• Jianqi Dong,
• Miao He and
• Xingfu Wang

Beilstein J. Nanotechnol. 2020, 11, 1623–1630, doi:10.3762/bjnano.11.145

• effect based on the ZnO pyroelectric material. Moreover, response time and high sensitivity are almost the same at each wavelength, and the device exhibits excellent stability and repeatability in the UV–visible–NIR range. Therefore, the self-powered p-Si/n-ZnO NWs heterojunction device can be applied in

Gas-sensing features of nanostructured tellurium thin films

• Dumitru Tsiulyanu

Beilstein J. Nanotechnol. 2020, 11, 1010–1018, doi:10.3762/bjnano.11.85

• hydrothermal recrystallization [23]. The response time range of NH3 gas sensors based on such nanocomponents was 5–18 s but the recovery time ranged between 170–720 s. From comparison with state-of-the-art devices, it can be observed that the physically nanostructured Te thin films exhibit great potential for

• time delay between measurements was 2 s, which was, simultaneously, much smaller than the sensor response time and much higher than the assessed dielectric relaxation time value. In order to transform the resistance signal into a voltage signal, the sample was connected in series to a load resistance

• current (in %/ppm) according to Equation 1: where Ia and Ig are the currents flowing through the specimen in air and in the presence of NO2, respectively, and C is the gas concentration. Figure 4 shows that, independent of the operating temperature, the recovery time (trv) is longer than the response time

Hexagonal boron nitride: a review of the emerging material platform for single-photon sources and the spin–photon interface

• Stefania Castelletto,
• Faraz A. Inam,
• Shin-ichiro Sato and
• Alberto Boretti

Beilstein J. Nanotechnol. 2020, 11, 740–769, doi:10.3762/bjnano.11.61

• ) = < 0.5, two emitters when g(2)(0) ≈ 0.5, 3 emitters g(2)(0) ≈ 0.67, and so on. In fact, due to the photon counts background and finite response time of the correlation measurements are limited today by the convolution of the time response of the two SP detectors, g(2)(0) ≠ 0, in the case of the SP

Electromigration-induced directional steps towards the formation of single atomic Ag contacts

• Atasi Chatterjee,
• Christoph Tegenkamp and
• Herbert Pfnür

Beilstein J. Nanotechnol. 2020, 11, 680–687, doi:10.3762/bjnano.11.55

• increased. In the other case, the control went to the second loop, where momentary resistance changes (due to structural changes) were compared with preset feedback parameters with a response time of 10 ms. Abrupt changes in resistance took place at current densities of (5 ± 2) × 1013 A/m2 and at voltages