Doxorubicin-loaded gold nanorods: a multifunctional chemo-photothermal nanoplatform for cancer management

• Uzma Azeem Awan,
• Abida Raza,
• Shaukat Ali,
• Rida Fatima Saeed and
• Nosheen Akhtar

Beilstein J. Nanotechnol. 2021, 12, 295–303, doi:10.3762/bjnano.12.24

• prepared by simple wet chemistry. A polymer was electrostatically conjugated, which facilitates the loading of DOX and its phototriggered release inside cancer cells in acidic environment. A comparatively good photothermal transfer ability has been achieved at a very low power density of 1.5 W/cm2 of NIR

• light into heat and kill heat-sensitive cancer cells with minimal side effects on the surrounding healthy cells due to the low power density of the laser and the shorter time of exposure. At the same time, the DOX release stimulated by the temperature rise could inhibit the proliferation of residual

TiO_x/Pt₃Ti(111) surface-directed formation of electronically responsive supramolecular assemblies of tungsten oxide clusters

• Marco Moors,
• Yun An,
• Agnieszka Kuc and
• Kirill Yu. Monakhov

Beilstein J. Nanotechnol. 2021, 12, 203–212, doi:10.3762/bjnano.12.16

• oxide; tungsten oxide; Introduction Molecular electronics has developed to a fast-growing research field in the past decades. Aspects such as low-cost fabrication and potentially high scalability down to the level of single molecules, resulting directly in a very low power consumption, make this type

Toward graphene textiles in wearable eye tracking systems for human–machine interaction

• Ata Jedari Golparvar and
• Murat Kaya Yapici

Beilstein J. Nanotechnol. 2021, 12, 180–189, doi:10.3762/bjnano.12.14

• , however, by being either invasive, expensive, or bulky [2][3][4] do not address the requirements of a readily usable product in HCI intended for widespread use; and fail to meet the fundamental characteristics of wearability in terms of size miniaturization, low-power operation, ergonomics, and aesthetics

• ) module, such as HM-10, which has low power consumption and offers a higher range up to several tens of meters. Results and Discussion Different eye movements along with a detection and classification algorithm having a success rate ranging from 85% up to 100% for detecting eleven different patterns over

• . Conclusion In contrast to well-established vision-based gaze tracking, we demonstrate electrooculography (EOG) with truly wearable graphene textiles, enabling an effective, low-cost, low-power, body-worn embedded system with small form factor to monitor and utilize eye movements for the remote control of

Molecular dynamics modeling of the influence forming process parameters on the structure and morphology of a superconducting spin valve

• Alexander Vakhrushev,
• Aleksey Fedotov,
• Vladimir Boian,
• Roman Morari and
• Anatolie Sidorenko

Beilstein J. Nanotechnol. 2020, 11, 1776–1788, doi:10.3762/bjnano.11.160

• ferromagnetic layers causes a restructuring of the magnetic moment configuration under low-power magnetic fields and switches the spin valve from a high to a low resistance state. When a superconducting film is used as a magneto-resistive interlayer, a superconducting spin valve is obtained. Furthermore, these

Triboelectric nanogenerator based on Teflon/vitamin B1 powder for self-powered humidity sensing

• Liangyi Zhang,
• Huan Li,
• Yiyuan Xie,
• Jing Guo and
• Zhiyuan Zhu

Beilstein J. Nanotechnol. 2020, 11, 1394–1401, doi:10.3762/bjnano.11.123

• output power density of the TVB-TENG can reach 120.13 µW/cm2. In addition, the approximate values of the open-circuit voltage (Voc) and short-circuit current (Isc) of this device were 340 V and 46.3 μA, respectively. These results indicate that sufficient power can be supplied to systems with low power

Analysis of catalyst surface wetting: the early stage of epitaxial germanium nanowire growth

• Owen C. Ernst,
• Felix Lange,
• David Uebel,
• Thomas Teubner and
• Torsten Boeck

Beilstein J. Nanotechnol. 2020, 11, 1371–1380, doi:10.3762/bjnano.11.121

• materials are, therefore, promising for gate-all-around architectures [16][17], which are very attractive for future low-power field-effect transistors (FETs) [18] and thermoelectrics [19][20][21]. The formation of nanodroplets leads to various outcomes, depending on the combination of substrate and droplet

Effect of localized helium ion irradiation on the performance of synthetic monolayer MoS₂ field-effect transistors

• Jakub Jadwiszczak,
• Pierce Maguire,
• Conor P. Cullen,
• Georg S. Duesberg and
• Hongzhou Zhang

Beilstein J. Nanotechnol. 2020, 11, 1329–1335, doi:10.3762/bjnano.11.117

• materials; Introduction Layered two-dimensional (2D) semiconductors have come to the fore in recent years as promising candidates for the implementation of flexible, transparent, and low-power electronics. In particular, transition metal dichalcogenides (TMDs), such as molybdenum disulfide (MoS2), have

Photothermally active nanoparticles as a promising tool for eliminating bacteria and biofilms

• Mykola Borzenkov,
• Piersandro Pallavicini,
• Angelo Taglietti,
• Laura D’Alfonso,
• Maddalena Collini and
• Giuseppe Chirico

Beilstein J. Nanotechnol. 2020, 11, 1134–1146, doi:10.3762/bjnano.11.98

• . The local photothermal effect triggered by the NIR irradiation of PVA-GNS films was highly efficient in eliminating E. coli bacteria, as shown in Figure 4. In a very recent study, the antimicrobial activity of a chitosan-based hydrogel with embedded gold nanorods under low-power (200 mW) diode laser

Microwave photon detection by an Al Josephson junction

• Leonid S. Revin,
• Andrey L. Pankratov,
• Anna V. Gordeeva,
• Anton A. Yablokov,
• Igor V. Rakut,
• Victor O. Zbrozhek and
• Leonid S. Kuzmin

Beilstein J. Nanotechnol. 2020, 11, 960–965, doi:10.3762/bjnano.11.80

• calibrated with a commercial spectrum analyzer. The high-frequency signal was varied from a high power, at which the Shapiro steps and photon-assisted tunneling steps are well pronounced at the I–V-curve, to a low power, the presence of which can be observed only in the switching histograms and in the

Multilayer capsules made of weak polyelectrolytes: a review on the preparation, functionalization and applications in drug delivery

• Varsha Sharma and
• Anandhakumar Sundaramurthy

Beilstein J. Nanotechnol. 2020, 11, 508–532, doi:10.3762/bjnano.11.41

Nanosecond resistive switching in Ag/AgI/PtIr nanojunctions

• Botond Sánta,
• Dániel Molnár,
• Patrick Haiber,
• Agnes Gubicza,
• Edit Szilágyi,
• Zsolt Zolnai,
• András Halbritter and
• Miklós Csontos

Beilstein J. Nanotechnol. 2020, 11, 92–100, doi:10.3762/bjnano.11.9

• Nanometer-scale resistive switching devices operated in the metallic conductance regime offer ultimately scalable and widely reconfigurable hardware elements for novel in-memory and neuromorphic computing architectures. Moreover, they exhibit high operation speed at low power arising from the ease of the

Deterministic placement of ultra-bright near-infrared color centers in arrays of silicon carbide micropillars

• Stefania Castelletto,
• Abdul Salam Al Atem,
• Faraz Ahmed Inam,
• Hans Jürgen von Bardeleben,
• Sophie Hameau,
• Ahmed Fahad Almutairi,
• Gérard Guillot,
• Shin-ichiro Sato,
• Alberto Boretti and
• Jean Marie Bluet

Beilstein J. Nanotechnol. 2019, 10, 2383–2395, doi:10.3762/bjnano.10.229

• capture saturation. In Figure 7c the fluorescence enhancement of the VSi emission was measured for many pillars (more than 100) for each sample in the linear low-power pumping regime. Higher enhancements for sample 1 and sample 4 are observed, with an increased enhancement for the sample with the lower

Multiwalled carbon nanotube based aromatic volatile organic compound sensor: sensitivity enhancement through 1-hexadecanethiol functionalisation

• Nadra Bohli,
• Meryem Belkilani,
• Juan Casanova-Chafer,
• Eduard Llobet and
• Adnane Abdelghani

Beilstein J. Nanotechnol. 2019, 10, 2364–2373, doi:10.3762/bjnano.10.227

• pressing market need for sensitive, fast response, low power consumption and stable sensors. Benzene and toluene detection is subject to several potential applications such as air monitoring in chemical industries or even biosensing of human breath. In this work, we report the fabrication of a room

Nonlinear absorption and scattering of a single plasmonic nanostructure characterized by x-scan technique

• Tushar C. Jagadale,
• Dhanya S. Murali and
• Shi-Wei Chu

Beilstein J. Nanotechnol. 2019, 10, 2182–2191, doi:10.3762/bjnano.10.211

• profiles. Linear response: Gaussian PSF Spherical gold nanostructures dispersed on a glass surface are examined with the two-channel x-scan method. Figure 2 shows the power-dependent scattering images and the corresponding signal profiles in the low-power region, manifesting linear responses. Figure 2a and

Microbubbles decorated with dendronized magnetic nanoparticles for biomedical imaging: effective stabilization via fluorous interactions

• Da Shi,
• Justine Wallyn,
• Dinh-Vu Nguyen,
• Francis Perton,
• Delphine Felder-Flesch,
• Sylvie Bégin-Colin,
• Mounir Maaloum and
• Marie Pierre Krafft

Beilstein J. Nanotechnol. 2019, 10, 2103–2115, doi:10.3762/bjnano.10.205

• exploits the sound attenuation undergone by multifrequency ultrasound waves that propagate through the aqueous bubble dispersion. Standard simple-harmonic resonator curves are fitted to measure the attenuation in order to infer the radii of the bubbles. A low-power emitter is used to avoid alteration of

Gas sensing properties of individual SnO₂ nanowires and SnO₂ sol–gel nanocomposites

• Alexey V. Shaposhnik,
• Dmitry A. Shaposhnik,
• Sergey Yu. Turishchev,
• Olga A. Chuvenkova,
• Stanislav V. Ryabtsev,
• Alexey A. Vasiliev,
• Xavier Vilanova,
• Francisco Hernandez-Ramirez and
• Joan R. Morante

Beilstein J. Nanotechnol. 2019, 10, 1380–1390, doi:10.3762/bjnano.10.136

• phenomenon can be explained by two factors. The first one is the single crystal character of the nanowires. Uniform adsorption enthalpy of all the centers is typical of Langmuir-type adsorption, which is characterized by low power factors in the power-law approximation. Vice versa, the small size of

Hydrophilicity and carbon chain length effects on the gas sensing properties of chemoresistive, self-assembled monolayer carbon nanotube sensors

• Juan Casanova-Cháfer,
• Carla Bittencourt and
• Eduard Llobet

Beilstein J. Nanotechnol. 2019, 10, 565–577, doi:10.3762/bjnano.10.58

• response and selectivity. This would make the detection of polar and nonpolar gas species employing low-power gas sensors easier, even under fluctuating ambient moisture conditions. Keywords: carbon length chain; gas sensing mechanism; hydrophilicity; hydrophobicity; multiwall carbon nanotubes (MWCNTs

• semiconducting character before being integrated in gas sensing devices. In view of developing sensitive, fast-responding, low power consumption and more selective sensors towards nitrogen dioxide or ethanol, in this paper, we combine oxygen plasma treated, Au-decorated MWCNTs with different thiols (see Figure

• (e.g., enhancement in signal intensity) cannot be observed. The reason could be due to the extremely low power of the laser used to record the Raman spectra, in order to prevent damaging the SAMs. As a consequence, a possible explanation is that the applied energy was not enough to create an important

Polymorphic self-assembly of pyrazine-based tectons at the solution–solid interface

• Achintya Jana,
• Puneet Mishra and
• Neeladri Das

Beilstein J. Nanotechnol. 2019, 10, 494–499, doi:10.3762/bjnano.10.50

• ); organic molecules; pyrazine; pyridines; scanning tunneling microscopy; self-assembly; Introduction Molecular materials are attracting considerable attention for the fabrication of next-generation functional devices owing to their high density and low power requirements. Several recent studies have

Geometrical optimisation of core–shell nanowire arrays for enhanced absorption in thin crystalline silicon heterojunction solar cells

• Robin Vismara,
• Olindo Isabella,
• Andrea Ingenito,
• Fai Tong Si and
• Miro Zeman

Beilstein J. Nanotechnol. 2019, 10, 322–331, doi:10.3762/bjnano.10.31

• , a 100 nm thick transparent tin-doped indium oxide (In2O3:Sn, ITO) was deposited at low power and low temperature, using radio-frequency (RF) magnetron sputtering. The cell area was defined as 5 mm × 5 mm, using a mask during ITO deposition. The reported equivalent thickness values of thin films on

Raman study of flash-lamp annealed aqueous Cu₂ZnSnS₄ nanocrystals

• Yevhenii Havryliuk,
• Oleksandr Selyshchev,
• Mykhailo Valakh,
• Alexandra Raevskaya,
• Oleksandr Stroyuk,
• Constance Schmidt,
• Volodymyr Dzhagan and
• Dietrich R. T. Zahn

Beilstein J. Nanotechnol. 2019, 10, 222–227, doi:10.3762/bjnano.10.20

• J/cm2 a high-quality CZTS signal could be observed again. This is probably related to the removal/evaporation of the secondary phases during FLA. Importantly, no notable influence of the inert atmosphere was detected. Therefore, the low-power FLA crystallization, which turned out to be successful

pH-mediated control over the mesostructure of ordered mesoporous materials templated by polyion complex micelles

• Emilie Molina,
• Mélody Mathonnat,
• Jason Richard,
• Patrick Lacroix-Desmazes,
• Martin In,
• Philippe Dieudonné,
• Thomas Cacciaguerra,
• Corine Gérardin and
• Nathalie Marcotte

Beilstein J. Nanotechnol. 2019, 10, 144–156, doi:10.3762/bjnano.10.14

• scattering (SAXS) and electron microscopy. SAXS measurements were performed in transmission mode on an in-house setup at the Laboratoire Charles Coulomb (Université Montpellier, France) using a high brightness, low power X-ray tube (λ = 1.5418 Å). All the intensities were corrected from transmission and

Wet chemistry route for the decoration of carbon nanotubes with iron oxide nanoparticles for gas sensing

• Hussam M. Elnabawy,
• Juan Casanova-Chafer,
• Badawi Anis,
• Mostafa Fedawy,
• Mattia Scardamaglia,
• Carla Bittencourt,
• Ahmed S. G. Khalil,
• Eduard Llobet and
• Xavier Vilanova

Beilstein J. Nanotechnol. 2019, 10, 105–118, doi:10.3762/bjnano.10.10

• sensors can be intrinsically low-power devices make them very attractive for their integration in ubiquitous, unattended mobile sensing nodes running on small batteries or on energy harvested from their environment [4]. Among the wide range of functionalization strategies that can be envisaged for

Charged particle single nanometre manufacturing

• Philip D. Prewett,
• Cornelis W. Hagen,
• Claudia Lenk,
• Steve Lenk,
• Marcus Kaestner,
• Tzvetan Ivanov,
• Ahmad Ahmad,
• Ivo W. Rangelow,
• Xiaoqing Shi,
• Stuart A. Boden,
• Alex P. G. Robinson,
• Dongxu Yang,
• Sangeetha Hari,
• Marijke Scotuzzi and
• Ejaz Huq

Beilstein J. Nanotechnol. 2018, 9, 2855–2882, doi:10.3762/bjnano.9.266

• intense electron irradiation if the lithography takes place under ambient conditions. Unlike tSPL, FE-eSPL structuring is a cold process due to the low power density which has advantages when patterning over thin active device regions, which is common in R&D applications. In this respect, FE-eSPL avoids

Optimization of Mo/Cr bilayer back contacts for thin-film solar cells

• Nima Khoshsirat,
• Fawad Ali,
• Vincent Tiing Tiong,
• Mojtaba Amjadipour,
• Hongxia Wang,
• Mahnaz Shafiei and
• Nunzio Motta

Beilstein J. Nanotechnol. 2018, 9, 2700–2707, doi:10.3762/bjnano.9.252

• layer [10][11][12][13]. This involves the deposition of a thick Mo layer with low resistivity at low pressure and high sputtering power on a thin Mo layer deposited at high pressure and low power providing the required adhesion to the substrate. However, this method still does not guarantee the adhesion

Electrospun one-dimensional nanostructures: a new horizon for gas sensing materials

• Muhammad Imran,
• Nunzio Motta and
• Mahnaz Shafiei

Beilstein J. Nanotechnol. 2018, 9, 2128–2170, doi:10.3762/bjnano.9.202

• followed by death. Gas sensors are the primary devices used for the detection and monitoring of these pollutants. Employing nanotechnology in sensor applications has significantly improved the performance of such devices, providing enhanced sensitivity, selectivity, low power consumption and high