Effect of repeating hydrothermal growth processes and rapid thermal annealing on CuO thin film properties

• Monika Ozga,
• Eunika Zielony,
• Aleksandra Wierzbicka,
• Anna Wolska,
• Marcin Klepka,
• Marek Godlewski,
• Bogdan J. Kowalski and
• Bartłomiej S. Witkowski

Beilstein J. Nanotechnol. 2024, 15, 743–754, doi:10.3762/bjnano.15.62

• work [47], outlining the fabrication of structured CuO films on fluorine-doped tin oxide from a solution devoid of additional substances. Post-processing plays a significant role in the field of nanomaterials fabrication. Metal oxide thin films often undergo annealing. This practice aims to improve the

Ni, Co, Zn, and Cu metal-organic framework-based nanomaterials for electrochemical reduction of CO₂: A review

• Ha Huu Do and
• Hai Bang Truong

Beilstein J. Nanotechnol. 2023, 14, 904–911, doi:10.3762/bjnano.14.74

• catalyst for CO2RR. The author postulated that Co(II) is converted into Co(I), which acts as a redox center for the reduction of CO2 into CO (Figure 3c,d). Because of their poor conductivity, Co-MOFs are typically grown on conductive templates, such as fluorine-doped tin oxide (FTO), carbon cloth, and

Influence of thickness and morphology of MoS₂ on the performance of counter electrodes in dye-sensitized solar cells

• Lam Thuy Thi Mai,
• Hai Viet Le,
• Ngan Kim Thi Nguyen,
• Van La Tran Pham,
• Thu Anh Thi Nguyen,
• Nguyen Thanh Le Huynh and
• Hoang Thai Nguyen

Beilstein J. Nanotechnol. 2022, 13, 528–537, doi:10.3762/bjnano.13.44

• disulfide (MoS2) was prepared on substrates coated with fluorine-doped tin oxide (FTO) to substitute the platinum counter electrode (CE) for dye-sensitized solar cells (DSSCs). Herein, we synthesized layered and honeycomb-like MoS2 thin films via the cyclic voltammetry (CV) route. Thickness and morphology

• , 25 μm), 18NR-T transparent titania paste (particle size of 20 nm), 18NR-AO active opaque titania paste (particle sizes of 20 and 450 nm), fluorine-doped tin oxide (FTO, TEC8 glass plates, 8 Ω·cm−2, 2.2 mm thickness), and N719 industry standard dye (N719) were purchased from Dyesol (Australia). All

Tin dioxide nanomaterial-based photocatalysts for nitrogen oxide oxidation: a review

• Viet Van Pham,
• Hong-Huy Tran,
• Thao Kim Truong and
• Thi Minh Cao

Beilstein J. Nanotechnol. 2022, 13, 96–113, doi:10.3762/bjnano.13.7

• ] synthesized SnO2 microspheres on a fluorine-doped tin oxide (FTO) substrate and the SEM images (Figure 6) show SnO2 microspheres with an average diameter of 2.0–2.5 μm. By using SnO2 microsphere photocatalysts for the photocatalytic oxidation of NO, Le et al. [67] indicated that 3D hierarchical flower-like

Boosting of photocatalytic hydrogen evolution via chlorine doping of polymeric carbon nitride

• Malgorzata Aleksandrzak,
• Michalina Kijaczko,
• Wojciech Kukulka,
• Daria Baranowska,
• Martyna Baca,
• Beata Zielinska and
• Ewa Mijowska

Beilstein J. Nanotechnol. 2021, 12, 473–484, doi:10.3762/bjnano.12.38

• potentiostat in a three-electrode test cell with a platinum wire as the counter electrode and the saturated calomel electrode (SCE) as the reference. The working electrode was a fluorine-doped tin oxide (FTO) glass with the analyzed material drop-casted from a 0.2% ethanol/Nafion solution. A 0.5 M sodium

Atomic layer deposited films of Al₂O₃ on fluorine-doped tin oxide electrodes: stability and barrier properties

• Hana Krýsová,
• Michael Neumann-Spallart,
• Hana Tarábková,
• Pavel Janda,
• Ladislav Kavan and
• Josef Krýsa

Beilstein J. Nanotechnol. 2021, 12, 24–34, doi:10.3762/bjnano.12.2

• , Technická 5, 166 28 Prague 6, Czech Republic 10.3762/bjnano.12.2 Abstract Al2O3 layers were deposited onto electrodes by atomic layer deposition. Solubility and electron-transport blocking were tested. Films deposited onto fluorine-doped tin oxide (FTO, F:SnO2/glass) substrates blocked electron transfer to

• alumina coatings was ascribed to its capability of passivating semiconductor/electrolyte interfaces, thus reducing photogenerated charge-carrier recombination (e.g., on BiVO4 [16]). In this work, Al2O3 films were deposited via ALD on thermally grown SiO2 on silicon or on fluorine-doped tin oxide (FTO

• grade. 0.1 M sodium phosphate buffer solution, pH 7.2, was obtained from Fluka. Triply distilled water was used for the preparation of solutions. Fluorine-doped tin oxide-coated 2 mm thick glass (TEC-7, 7 Ω/□, Sigma-Aldrich), was ultrasonically pre-cleaned with isopropanol, treated with acetone, ethanol

Structural and electronic properties of SnO₂ doped with non-metal elements

• Jianyuan Yu,
• Yingeng Wang,
• Yan Huang,
• Xiuwen Wang,
• Jing Guo,
• Jingkai Yang and
• Hongli Zhao

Beilstein J. Nanotechnol. 2020, 11, 1321–1328, doi:10.3762/bjnano.11.116

• research works has been done examining different doping elements. Doped tin oxide thin film have been widely used in the fields of thin film solar cell electrodes, electronic display devices, and gas sensors. Also doped SnO2 been used for energy-saving low-emissivity glass coatings due to low resistivity

Site-specific growth of oriented ZnO nanocrystal arrays

• Rekha Bai,
• Dinesh K. Pandya,
• Sujeet Chaudhary,
• Veer Dhaka,
• Vladislav Khayrudinov,
• Jori Lemettinen,
• Christoffer Kauppinen and
• Harri Lipsanen

Beilstein J. Nanotechnol. 2019, 10, 274–280, doi:10.3762/bjnano.10.26

• grow ZnO nanocrystals on both bare and on an array of pores patterned on the polymer-coated indium-doped tin oxide (ITO) conducting substrates. The patterning process for the polymer, poly(Disperse Red 1 acrylate), involves laser interference lithography and oxygen plasma etching and has been reported

Zn/F-doped tin oxide nanoparticles synthesized by laser pyrolysis: structural and optical properties

• Florian Dumitrache,
• Iuliana P. Morjan,
• Elena Dutu,
• Ion Morjan,
• Claudiu Teodor Fleaca,
• Monica Scarisoreanu,
• Alina Ilie,
• Marius Dumitru,
• Cristian Mihailescu,
• Adriana Smarandache and
• Gabriel Prodan

Beilstein J. Nanotechnol. 2019, 10, 9–21, doi:10.3762/bjnano.10.2

• promising, lower cost, but good performing material alternatives to ITO for these types of applications is fluorine-doped tin oxide (FTO) [8]. Regarding the cation doping for the synthesis of tin-based transparent and conductive oxidic (TCO) materials, the literature has been focused on doping with i

• solutions [13] and iv.) iron by laser pyrolysis [14][15] or by electron beam evaporation [16]. Cobalt-doped tin oxide has also been reported, and the resulting polycrystalline films were prepared by spin-coating and annealing from chloride ethanolic solutions resulted in lower bandgap values than pure SnO2

• [17]. Highly conductive films based on amorphous Co-doped SnO2 were also synthesized using a pulsed spray evaporation chemical vapor deposition (CVD) technique [18]. One of the most reported cationic dopants for tin oxide is Zn2+, where the obtained zinc-doped tin oxide (ZTO) films show lower bandgap

Thickness-dependent photoelectrochemical properties of a semitransparent Co₃O₄ photocathode

• Malkeshkumar Patel and
• Joondong Kim

Beilstein J. Nanotechnol. 2018, 9, 2432–2442, doi:10.3762/bjnano.9.228

• heterojunctions. Experimental Sample fabrication: The photocathode was composed of Co3O4/fluorine-doped tin oxide (FTO)/glass. The general synthesis of Kirkendall diffusion grown Co3O4 film was analogue to our previous study [20]. In brief, a commercial fluorine-doped tin oxide (FTO)-coated glass (735167, Sigma

Know your full potential: Quantitative Kelvin probe force microscopy on nanoscale electrical devices

• Amelie Axt,
• Ilka M. Hermes,
• Victor W. Bergmann,
• Niklas Tausendpfund and
• Stefan A. L. Weber

Beilstein J. Nanotechnol. 2018, 9, 1809–1819, doi:10.3762/bjnano.9.172

• , visualized by the red and blue line, respectively. The cell consisted of a fluorine-doped tin oxide (FTO) electrode, a compact TiO2 electron extraction layer and a mesoscopic TiO2 layer (meso) filled with the perovskite light-absorber methylammonium lead iodide (MAPI). The mesoscopic layer was followed by a

Enhanced photoelectrochemical water splitting performance using morphology-controlled BiVO₄ with W doping

• Xin Zhao and
• Zhong Chen

Beilstein J. Nanotechnol. 2017, 8, 2640–2647, doi:10.3762/bjnano.8.264

• diffraction was used to characterize the crystal structure of the obtained films. Figure 2 shows that all peaks agree well with the ones of BiVO4 (PDF#14-0688). No peaks belonging to other phases were present except the ones from the fluorine-doped tin oxide (SnO2) substrate. This demonstrates BiVO4 thin

PTFE-based microreactor system for the continuous synthesis of full-visible-spectrum emitting cesium lead halide perovskite nanocrystals

• Chengxi Zhang,
• Weiling Luan,
• Yuhang Yin and
• Fuqian Yang

Beilstein J. Nanotechnol. 2017, 8, 2521–2529, doi:10.3762/bjnano.8.252

• (XRD) measurements were performed on a Rigaku D/max2550 (Rigaku, USA) device operating with Cu Kα (λ = 0.154056 nm), and the QDs were spin-coated on fluorine-doped tin oxide glass. (a) Color luminescence under ultraviolet light and (b) photoluminescence of CsPbX3 quantum dot solutions. High-resolution

Three-in-one approach towards efficient organic dye-sensitized solar cells: aggregation suppression, panchromatic absorption and resonance energy transfer

• Jayita Patwari,
• Samim Sardar,
• Bo Liu,
• Peter Lemmens and
• Samir Kumar Pal

Beilstein J. Nanotechnol. 2017, 8, 1705–1713, doi:10.3762/bjnano.8.171

• (SQ2) and 60 μm thick Surlyn were bought from Solaronix. Dimethyl sulfoxide (DMSO), acetonitrile and ethanol (≥99%) were purchased from Merck, and Ultrapure water was obtained from Millipore System, (18.2 MΩ·cm). The conducting glass substrate with fluorine-doped tin oxide (FTO) was purchased from

Oxidative stabilization of polyacrylonitrile nanofibers and carbon nanofibers containing graphene oxide (GO): a spectroscopic and electrochemical study

• İlknur Gergin,
• Ezgi Ismar and
• A. Sezai Sarac

Beilstein J. Nanotechnol. 2017, 8, 1616–1628, doi:10.3762/bjnano.8.161

• ). Carbonized nanofibers were used as free standing electrodes whereas oxidized nanofibers were deposited on fluorine-doped tin oxide (FTO) glass to use as working electrodes. EIS analysis were investigated in 0.1 M NaClO4/ACN electrolyte in a frequency range of 10 mHz to 100 kHz at open circuit potential with

Thin SnO_x films for surface plasmon resonance enhanced ellipsometric gas sensing (SPREE)

• Daniel Fischer,
• Andreas Hertwig,
• Uwe Beck,
• Volkmar Lohse,
• Detlef Negendank,
• Martin Kormunda and
• Norbert Esser

Beilstein J. Nanotechnol. 2017, 8, 522–529, doi:10.3762/bjnano.8.56

• the problems of cross sensitivity of the MOS concept. Results: Undoped tin oxide (SnOx) and iron doped tin oxide (Fe:SnOx) thin add-on films were prepared by magnetron sputtering on the top of the actual surface plasmon resonance (SPR) sensing gold layer. The films were tested for their sensitivity to

• sensing devices with different coated SPREE sensors. Keywords: doped tin oxide; ellipsometry; gas sensing; surface plasmon resonance; thin films; transparent conductive oxides; Introduction Gas sensors are an important tool for example in the fields of process monitoring, workplace safety or

• support the theory of a dependence of the binding sites to the response in the gas measurement, iron doped tin oxide (Fe:SnOx) overcoated sensors with an increased number of binding sites for CO were built [33]. This was achieved by adding a block of metallic iron to the target. A gas sensing measurement

Performance of natural-dye-sensitized solar cells by ZnO nanorod and nanowall enhanced photoelectrodes

• Saif Saadaoui,
• Mohamed Aziz Ben Youssef,
• Moufida Ben Karoui,
• Rached Gharbi,
• Emanuele Smecca,
• Vincenzina Strano,
• Salvo Mirabella,
• Alessandra Alberti and
• Rosaria A. Puglisi

Beilstein J. Nanotechnol. 2017, 8, 287–295, doi:10.3762/bjnano.8.31

•  6a gives the SEM images illustrating the morphology of the ZnO NRs annealed in forming gas (FG) (N2/H2, 95:5). From this figure, we observe that nanorods cover the entire surface of the fluorine-doped tin oxide (FTO) conductive glass and have a hexagonal shape with uniform size and length [23]. The

Sb₂S₃ grown by ultrasonic spray pyrolysis and its application in a hybrid solar cell

• Erki Kärber,
• Atanas Katerski,
• Ilona Oja Acik,
• Arvo Mere,
• Valdek Mikli and
• Malle Krunks

Beilstein J. Nanotechnol. 2016, 7, 1662–1673, doi:10.3762/bjnano.7.158

• , situated in the electrical junction created by TiO2 and P3HT (polythiophene) as the electron and hole conductor, respectively. For these type of solar cells, fluorine doped tin oxide (FTO) is prevalently used to contact the TiO2 while evaporated Au has been used to contact the P3HT. The use of a polymeric

Synthesis and applications of carbon nanomaterials for energy generation and storage

• Marco Notarianni,
• Jinzhang Liu,
• Kristy Vernon and
• Nunzio Motta

Beilstein J. Nanotechnol. 2016, 7, 149–196, doi:10.3762/bjnano.7.17

Experimental determination of the light-trapping-induced absorption enhancement factor in DSSC photoanodes

• Serena Gagliardi and
• Mauro Falconieri

Beilstein J. Nanotechnol. 2015, 6, 886–892, doi:10.3762/bjnano.6.91

• . Experimental Preparation of photoanodes and cell assembly A standard procedure was used as described in many literature papers [15] using fluorine-doped tin oxide (FTO) glasses, (Pilkinton TEC8®, 2 mm thick, cut in 2 × 2 cm2 square) as substrates. The photoactive layer was prepared by screen printing Solaronix

Optical modeling-assisted characterization of dye-sensitized solar cells using TiO₂ nanotube arrays as photoanodes

• Jung-Ho Yun,
• Il Ku Kim,
• Yun Hau Ng,
• Lianzhou Wang and
• Rose Amal

Beilstein J. Nanotechnol. 2014, 5, 895–902, doi:10.3762/bjnano.5.102

• . A sandwich-type DSSC was assembled using the dye-sensitized TNT array onto the Ti foil (20 × 20 mm2) as a photoelectrode and platinum-deposited fluorine-doped tin oxide (FTO) glass (20 × 15 mm2, Asahi, Rs ≤ 8 Ω·sq−1) as a counter electrode separated by a sealant (Surlyn 60 µm thickness, Solaronix

Biomolecule-assisted synthesis of carbon nitride and sulfur-doped carbon nitride heterojunction nanosheets: An efficient heterojunction photocatalyst for photoelectrochemical applications

• Hua Bing Tao,
• Hong Bin Yang,
• Jiazang Chen,
• Jianwei Miao and
• Bin Liu

Beilstein J. Nanotechnol. 2014, 5, 770–777, doi:10.3762/bjnano.5.89

• purging nitrogen for 30 min. The working electrode was prepared as the following: briefly, 10 mg of as-prepared sample was suspended in 1 mL of isopropyl alcohol (IPA). Then, 50 μL of the colloidal suspension (10 mg/mL) was dropcasted onto precleaned fluorine-doped tin oxide (FTO) substrate with a fixed

Kelvin probe force microscopy of nanocrystalline TiO₂ photoelectrodes

• Alex Henning,
• Gino Günzburger,
• Res Jöhr,
• Yossi Rosenwaks,
• Biljana Bozic-Weber,
• Catherine E. Housecroft,
• Edwin C. Constable,
• Ernst Meyer and
• Thilo Glatzel

Beilstein J. Nanotechnol. 2013, 4, 418–428, doi:10.3762/bjnano.4.49

• received substantial attention from both academic and industrial communities focusing on new materials and advanced device concepts [3][4][5][6][7][8]. A typical DSC consists of a dye-coated TiO2 photoelectrode, deposited on a fluorine-doped tin oxide (FTO) conductive-glass substrate, an redox-couple

Reduced electron recombination of dye-sensitized solar cells based on TiO₂ spheres consisting of ultrathin nanosheets with [001] facet exposed

• Hongxia Wang,
• Meinan Liu,
• Cheng Yan and
• John Bell

Beilstein J. Nanotechnol. 2012, 3, 378–387, doi:10.3762/bjnano.3.44

• dye-coated TiO2 electrode, which is deposited on a fluorine-doped tin oxide (FTO) conductive-glass substrate, a I−/I3− redox-couple-based electrolyte and a platinum counter electrode. Upon illumination, a photon with high energy (higher than the energy difference between the HOMO and LUMO level of the

• the TiO2 film before reaching the current collector, which is based on the conductive fluorine-doped tin oxide (FTO) substrate. Meanwhile, a parallel reaction, which involves transfer of the hole from the oxidized state of the dye (dye+) to the surrounding I− ions of the redox couple of the

• size of 20 nm was employed for comparison. Assembly of dye-sensitized solar cells The procedure for the fabrication of the dye-sensitized solar cells was reported in our previous work [11][12]. Briefly, a substrate based on fluorine-doped tin oxide (FTO) conductive glass (TEC15, Pilkington) was

Highly efficient ZnO/Au Schottky barrier dye-sensitized solar cells: Role of gold nanoparticles on the charge-transfer process

• Tanujjal Bora,
• Htet H. Kyaw,
• Soumik Sarkar,
• Samir K. Pal and
• Joydeep Dutta

Beilstein J. Nanotechnol. 2011, 2, 681–690, doi:10.3762/bjnano.2.73

• sensitizer dye molecules, the photoexcited electrons in the Au nanoparticles are transferred to the conduction band (CB) of ZnO, and then diffuse through the ZnO nanorods towards the conducting fluorine-doped tin oxide (FTO) substrate resulting in higher photocurrent and photovoltage, as observed. The