Influence of thickness and morphology of MoS₂ on the performance of counter electrodes in dye-sensitized solar cells

• Lam Thuy Thi Mai,
• Hai Viet Le,
• Ngan Kim Thi Nguyen,
• Van La Tran Pham,
• Thu Anh Thi Nguyen,
• Nguyen Thanh Le Huynh and
• Hoang Thai Nguyen

Beilstein J. Nanotechnol. 2022, 13, 528–537, doi:10.3762/bjnano.13.44

• -Newport-USA, Model No. 94061A). Simulated sunlight of 100 mW·cm−2 (1 sun) was generated and corrected by a 1000 W Xe lamp and an AM 1.5 filter. The photocurrent density–voltage (J–V) curves of the DSSCs were measured using a Keithley model 2400 multisource meter. Electrochemical impedance spectroscopy

The role of sulfonate groups and hydrogen bonding in the proton conductivity of two coordination networks

• Ali Javed,
• Felix Steinke,
• Stephan Wöhlbrandt,
• Hana Bunzen,
• Norbert Stock and
• Michael Tiemann

Beilstein J. Nanotechnol. 2022, 13, 437–443, doi:10.3762/bjnano.13.36

• , Germany 10.3762/bjnano.13.36 Abstract The proton conductivity of two coordination networks, [Mg(H2O)2(H3L)]·H2O and [Pb2(HL)]·H2O (H5L = (H2O3PCH2)2-NCH2-C6H4-SO3H), is investigated by AC impedance spectroscopy. Both materials contain the same phosphonato-sulfonate linker molecule, but have clearly

• the Pb-based metal-organic framework, in contrast, no extended hydrogen bonding occurs, as the sulfonate groups coordinate to Pb2+, without forming hydrogen bonds; the proton conductivity is much lower in this material. Keywords: coordination network; coordination polymer; impedance spectroscopy

• % were recorded on a Panalytical Empyrean diffractometer equipped with a CHC plus+ chamber in a transmittance Bragg–Brentano geometry employing Cu radiation. The patterns were recorded at a temperature of 25 °C before and after the activation of sample at 80 °C and 10% relative humidity. For impedance

A non-enzymatic electrochemical hydrogen peroxide sensor based on copper oxide nanostructures

• Irena Mihailova,
• Vjaceslavs Gerbreders,
• Marina Krasovska,
• Eriks Sledevskis,
• Valdis Mizers,
• Andrejs Bulanovs and
• Andrejs Ogurcovs

Beilstein J. Nanotechnol. 2022, 13, 424–436, doi:10.3762/bjnano.13.35

• following sections show the averaged data from all measurements. To determine the optimal scanning parameters that provide the maximum sensitivity of the sensor, the dependence of the electrochemical response on the pH of the buffer solution and on the scanning speed was studied. Impedance spectroscopy was

Tin dioxide nanomaterial-based photocatalysts for nitrogen oxide oxidation: a review

• Viet Van Pham,
• Hong-Huy Tran,
• Thao Kim Truong and
• Thi Minh Cao

Beilstein J. Nanotechnol. 2022, 13, 96–113, doi:10.3762/bjnano.13.7

• extending the light harvesting range and promoting the separation of photogenerated electrons. A considerable amount of reactive oxygen radicals was produced during the photocatalytic reaction, resulting from the large amount of free surface OH groups. PL, photocurrent response, electrochemical impedance

• spectroscopy (EIS) data, and the nanosecond-level time-resolved fluorescence decay spectra (Figure 11) demonstrated that the SnO2/NCDs/ZHS nanohybrid achieved low charge carrier recombination, high photoactivity, and excellent photoinduced charge transfer to the surface of the semiconductor. This study enables

Boosting of photocatalytic hydrogen evolution via chlorine doping of polymeric carbon nitride

• Malgorzata Aleksandrzak,
• Michalina Kijaczko,
• Wojciech Kukulka,
• Daria Baranowska,
• Martyna Baca,
• Beata Zielinska and
• Ewa Mijowska

Beilstein J. Nanotechnol. 2021, 12, 473–484, doi:10.3762/bjnano.12.38

• three cycles of light on–off, the performance of both electrodes tends to stabilize, indicating that the photocatalysts are stable under visible-light irradiation [55]. The measurements obtained from electrochemical impedance spectroscopy (EIS) are shown in Figure 9b. It is known that the arc radius of

• (F7000, Hitachi) with an excitation wavelength of 280 nm. The DRS was performed using a Jasco (Japan) spectrometer. The Kubelka–Munk function was used to calculate the bandgap energy. The photocurrent response and electrochemical impedance spectroscopy were measured using the Autolab PGSTAT302 N

Solution combustion synthesis of a nanometer-scale Co₃O₄ anode material for Li-ion batteries

• Monika Michalska,
• Huajun Xu,
• Qingmin Shan,
• Shiqiang Zhang,
• Yohan Dall'Agnese,
• Yu Gao,
• Amrita Jain and
• Marcin Krajewski

Beilstein J. Nanotechnol. 2021, 12, 424–431, doi:10.3762/bjnano.12.34

• Co3O4 electrode. In order to better understand of the capacitive behavior of the investigated Co3O4 electrode material, electrochemical impedance spectroscopy (EIS) measurements at a current density of 100 mA·g−1 were carried out before cycling and after the first, second, third, fourth, and fifth cycle

• using a Lanhe CT2001A. Electrochemical impedance spectroscopy (EIS) experiments were carried out to in the frequency range from 1 MHz to 1 mHz with a perturbation amplitude set at 10 mV on a potentiostat (VSP, Biologic-SAS). (a) XRD pattern and (b) Raman spectrum of Co3O4 powder. SEM images of Co3O4

• circuit corresponding to the electrochemical impedance spectroscopy (EIS) measurements for the cell (a) before cycling, and (b) after cycling; Rf – contact resistance, RSEI – the solid–electrolyte interface (SEI) resistance, CSEI – the surface capacitance, Rct – the charge transfer resistance at the

ZnO and MXenes as electrode materials for supercapacitor devices

• Ameen Uddin Ammar,
• Ipek Deniz Yildirim,
• Feray Bakan and
• Emre Erdem

Beilstein J. Nanotechnol. 2021, 12, 49–57, doi:10.3762/bjnano.12.4

• ) spectroscopy techniques among the most powerful techniques to extract detailed information on the defect structures of ZnO. Also, electrical impedance spectroscopy (EIS) and cyclic voltammetry (CV) are sensitive to electrical properties such as specific capacitance and impedance, which can be correlated with

Self-standing heterostructured NiC_x-NiFe-NC/biochar as a highly efficient cathode for lithium–oxygen batteries

• Shengyu Jing,
• Xu Gong,
• Shan Ji,
• Linhui Jia,
• Bruno G. Pollet,
• Sheng Yan and
• Huagen Liang

Beilstein J. Nanotechnol. 2020, 11, 1809–1821, doi:10.3762/bjnano.11.163

• impedance spectroscopy (EIS) in a frequency range from 100 kHz to 0.1 Hz and with a perturbation amplitude of 5 mV was used on the PARSTAT 4000 (AMETEK, USA) electrochemical workstation. Cyclic voltammetry (CV) was performed at a scan rate of 0.1 mV·s−1 and in a cell voltage range from 2.0 to 4.5 V vs Li

• existence of some amount of undecomposed Li2O2. Electrochemical impedance spectroscopy was also carried out to investigate NiFe-PBA/PP-T samples after the first charge and discharge (Figure 8c and Figure 8d). The illustrations (top part of Figure 8c and Figure 8d) show the corresponding equivalent circuit

Structure and electrochemical performance of electrospun-ordered porous carbon/graphene composite nanofibers

• Yi Wang,
• Yanhua Song,
• Chengwei Ye and
• Lan Xu

Beilstein J. Nanotechnol. 2020, 11, 1280–1290, doi:10.3762/bjnano.11.112

• station (CHI660E, Chenhua, Shanghai) by using cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and constant current galvanostatic charge/discharge (GCD) techniques. A voltage range of 0–1.0 V was applied to the CV electrode at a scan rate of 25 mV·s−1. The impedance measurements of

• of these electrodes exhibited similar symmetrical isosceles triangles, which were consistent with the characteristics of the double-layer capacitor electrode and with the results of the CV curves. Electrochemical impedance spectroscopy (EIS) is a reliable method used to characterize electrode

Nickel nanoparticles supported on a covalent triazine framework as electrocatalyst for oxygen evolution reaction and oxygen reduction reactions

• Secil Öztürk,
• Yu-Xuan Xiao,
• Dennis Dietrich,
• Beatriz Giesen,
• Juri Barthel,
• Jie Ying,
• Xiao-Yu Yang and
• Christoph Janiak

Beilstein J. Nanotechnol. 2020, 11, 770–781, doi:10.3762/bjnano.11.62

• good electrochemical ORR performance of Ni/CTF-1-600-22 was investigated by electrochemical impedance spectroscopy (EIS). As shown in Figure 7, all CTF-1-600 materials exhibited a higher conductivity than CTF-1-400. This could be ascribed to the higher graphitization degree achieved through the higher

• for ORR were performed in 1 mol/L KOH solution under air with cyclic potential sweeps between 0.6 and 1.1 V versus RHE at a 50 mV/s sweep rate for 2000 cycles. The electrochemical impedance spectroscopy (EIS) measurements were performed in 1 mol/L KOH, in a frequency range of (0.1–1) × 105 Hz and a

Exfoliation in a low boiling point solvent and electrochemical applications of MoO₃

• Matangi Sricharan,
• Bikesh Gupta,
• Sreejesh Moolayadukkam and
• H. S. S. Ramakrishna Matte

Beilstein J. Nanotechnol. 2020, 11, 662–670, doi:10.3762/bjnano.11.52

• supercapacitors [30][31]. The composite with 5 wt % CB was tested for about 500 cycles (Figure 3e). Initially the specific capacitance was found to increase, which can be attributed to the wetting of the active material in the initial cycles [26]. Electrochemical impedance spectroscopy was used to study the

• and the activation of available sites. Also, the composite shows a capacitance retention up to 94% even after 2000 cycles. Electrochemical impedance spectroscopy (EIS) is used to study the electrochemical series resistance and ideal nature of the capacitor. As shown in Figure 4f, EIS shows a typical

Comparison of fresh and aged lithium iron phosphate cathodes using a tailored electrochemical strain microscopy technique

• Matthias Simolka,
• Hanno Kaess and
• Kaspar Andreas Friedrich

Beilstein J. Nanotechnol. 2020, 11, 583–596, doi:10.3762/bjnano.11.46

• impedance spectroscopy (EIS), potentiostatic intermittent titration technique (PITT), galvanostatic intermittent titration technique (GITT), CV). These techniques assume a simultaneous participation of all LFP particles in the electrodes when a “domino-cascade” is presumed to more accurately reflect the

High-performance asymmetric supercapacitor made of NiMoO₄ nanorods@Co₃O₄ on a cellulose-based carbon aerogel

• Meixia Wang,
• Jing Zhang,
• Xibin Yi,
• Benxue Liu,
• Xinfu Zhao and
• Xiaochan Liu

Beilstein J. Nanotechnol. 2020, 11, 240–251, doi:10.3762/bjnano.11.18

• electrodes impede the diffusion less strongly, which is attributed to the faster transport of electrons and the charge transfer resistance (Rct). Fitting the electrochemical impedance spectroscopy (EIS) plots based on the equivalent circuit model (inset of Figure 6d), reveals a solution resistance (Rs) of

• (GCD) curves at different values of the current density ranging from 0.5 to 5.0 A/g of the NiMoO4@Co3O4/CA ternary composite. (c) Specific capacitance at various values of the current density and (d) electrochemical impedance spectroscopy (EIS) plots of pure ZIF-67 derived Co3O4 and NiMoO4@Co3O4/CA

Rational design of block copolymer self-assemblies in photodynamic therapy

• Maxime Demazeau,
• Laure Gibot,
• Anne-Françoise Mingotaud,
• Patricia Vicendo,
• Clément Roux and
• Barbara Lonetti

Beilstein J. Nanotechnol. 2020, 11, 180–212, doi:10.3762/bjnano.11.15

Polyvinylpyrrolidone as additive for perovskite solar cells with water and isopropanol as solvents

• Chen Du,
• Shuo Wang,
• Xu Miao,
• Wenhai Sun,
• Yu Zhu,
• Chengyan Wang and
• Ruixin Ma

Beilstein J. Nanotechnol. 2019, 10, 2374–2382, doi:10.3762/bjnano.10.228

• simulator (Newport Oriel Sol3A Class AAA, 64023A Simulator), which was calibrated using a NREL standard Si solar cell. Electrochemical impedance spectroscopy (EIS) measurements were conducted by using an electrochemical workstation (CHI660d) (1 MHz to 100 Hz) and for fitting the Zview software was used. The

• attributed to the appearance of voids on the surface of the perovskite layer, which results in a higher recombination rate of the carriers [34]. Figure 5 shows electrical impedance spectroscopy (EIS) measurements at a voltage bias of 0 V under one-sun light intensity with the test frequency ranging from 0.1

Design and facile synthesis of defect-rich C-MoS₂/rGO nanosheets for enhanced lithium–sulfur battery performance

• Chengxiang Tian,
• Juwei Wu,
• Zheng Ma,
• Bo Li,
• Pengcheng Li,
• Xiaotao Zu and
• Xia Xiang

Beilstein J. Nanotechnol. 2019, 10, 2251–2260, doi:10.3762/bjnano.10.217

• impedance spectroscopy (EIS) measurements were achieved at the open-circuit potential between 0.01 Hz and 100 kHz. All the tests were carried out at room temperature. Results and Discussion The preparation of the C-MoS2/rGO composite is shown in Figure 1. The C-MoS2/rGO composite is synthesized by the

• overlap, indicating the superior electrochemical reversibility of the C-MoS2/rGO-6-S cathode. The electrochemical impedance spectroscopy results of MoS2-S, C-MoS2/rGO-S, C-MoS2/rGO-6-S electrodes are shown in Figure 6b. Obviously, the C-MoS2/rGO-S and C-MoS2/rGO-6-S electrodes have the minor semicircles

Nontoxic pyrite iron sulfide nanocrystals as second electron acceptor in PTB7:PC₇₁BM-based organic photovoltaic cells

• Olivia Amargós-Reyes,
• José-Luis Maldonado,
• Omar Martínez-Alvarez,
• María-Elena Nicho,
• José Santos-Cruz,
• Juan Nicasio-Collazo,
• Irving Caballero-Quintana and
• Concepción Arenas-Arrocena

Beilstein J. Nanotechnol. 2019, 10, 2238–2250, doi:10.3762/bjnano.10.216

• the charge carrier transport and recombination in the devices based on PTB7:PC71BM and PTB7:PC71BM:FeS2 with 0.5 wt % FeS2, impedance spectroscopy (IS) was conducted. IS is an important technique for monitoring charge carrier transport and recombination processes in solar cells [59]. These

• noncontact mode. Impedance spectroscopy measurements (filled color squares) and simulations (black lines) of a) PTB7:PC71BM and b) PTB7:PC71BM:FeS2 with 0.5 wt % of FeS2; c) equivalent circuit used for the IS simulations; d) Rrec values vs bias voltage of PTB7:PC71BM (blue) and PTB7:PC71BM:FeS2 (with 0.5 wt

• -UNAM for financial support through the PAPIIT-IN115018 project. The authors acknowledge Lourdes Palma (INB-UNAM), Dra. Marina Vega (CGeo-UNAM), Martín Olmos (CIO) and Christian Albor (CIO) for their technical support and Dr. D. Barreiro-Argüelles (CIO) for impedance spectroscopy measurements.

A novel all-fiber-based LiFePO₄/Li₄Ti₅O₁₂ battery with self-standing nanofiber membrane electrodes

• Li-li Chen,
• Hua Yang,
• Mao-xiang Jing,
• Chong Han,
• Fei Chen,
• Xin-yu Hu,
• Wei-yong Yuan,
• Shan-shan Yao and
• Xiang-qian Shen

Beilstein J. Nanotechnol. 2019, 10, 2229–2237, doi:10.3762/bjnano.10.215

• agreement with the redox peaks in the CV curves. Figure 9 shows the electrical impedance spectroscopy curves of the two kinds of fiber membrane electrodes. It can be seen that there is a regular semicircle in the high-frequency region, which represents the magnitude of the charge transfer resistance Rct

• assembled in an Ar-filled glovebox by using lithium foil as anode and 1 M LiPF6 electrolyte (ethylene carbonate/dimethyl carbonate/ethyl methyl carbonate = 1:1:1). A Celgard 2400 polypropylene membrane was used as separator. The cyclic voltammetry and electrochemical impedance spectroscopy measurements were

Ultrathin Ni_1−xCo_xS₂ nanoflakes as high energy density electrode materials for asymmetric supercapacitors

• Xiaoxiang Wang,
• Teng Wang,
• Rusen Zhou,
• Lijuan Fan,
• Shengli Zhang,
• Feng Yu,
• Tuquabo Tesfamichael,
• Liwei Su and
• Hongxia Wang

Beilstein J. Nanotechnol. 2019, 10, 2207–2216, doi:10.3762/bjnano.10.213

• ) at room temperature of 24 °C. Electrochemical impedance spectroscopy (EIS) of the electrode material was carried out in the frequency range from 100 kHz to 0.01 Hz at AC voltage under open-circuit conditions. The cycling stability was tested by using a LAND system (Wuhan LAND electronics). The

Use of data processing for rapid detection of the prostate-specific antigen biomarker using immunomagnetic sandwich-type sensors

• Camila A. Proença,
• Tayane A. Freitas,
• Thaísa A. Baldo,
• Elsa M. Materón,
• Flávio M. Shimizu,
• Gabriella R. Ferreira,
• Frederico L. F. Soares,
• Ronaldo C. Faria and
• Osvaldo N. Oliveira Jr.

Beilstein J. Nanotechnol. 2019, 10, 2171–2181, doi:10.3762/bjnano.10.210

• can be adapted for multiplex detection of biomarkers, in addition to PSA, by combining with other proteins. We also demonstrated that information visualization techniques, so far most commonly used for impedance spectroscopy sensing data, can be applied to amperometric results with a microfluidic

Facile synthesis of carbon nanotube-supported NiO//Fe₂O₃ for all-solid-state supercapacitors

• Shengming Zhang,
• Xuhui Wang,
• Yan Li,
• Xuemei Mu,
• Yaxiong Zhang,
• Jingwei Du,
• Guo Liu,
• Xiaohui Hua,
• Yingzhuo Sheng,
• Erqing Xie and
• Zhenxing Zhang

Beilstein J. Nanotechnol. 2019, 10, 1923–1932, doi:10.3762/bjnano.10.188

• the CC-CNT@Fe2O3 electrode. Electrochemical impedance spectroscopy (EIS) was carried out to explore the resistance of the electrode (Figure 4d). The measured curve can be well fitted by equivalent circuits, and the insert is an enlarged view in the high-frequency area. All fitted values are shown in

• counter electrode, a saturated calomel electrode (SCE) as the reference electrode, and the CC-CNT@Fe2O3 or CC-CNT@NiO as the binder-free working electrode. Electrochemical impedance spectroscopy (EIS) curves were measured in frequencies from 100 kHz to 0.01 Hz at open-circuit voltage with an AC voltage

TiO₂/GO-coated functional separator to suppress polysulfide migration in lithium–sulfur batteries

• Ning Liu,
• Lu Wang,
• Taizhe Tan,
• Yan Zhao and
• Yongguang Zhang

Beilstein J. Nanotechnol. 2019, 10, 1726–1736, doi:10.3762/bjnano.10.168

• electrochemical impedance spectroscopy (EIS) analysis to analyze the charge transfer kinetics in Li/S batteries with pristine and TiO2/GO-coated separators. Figure 8 presents the Nyquist plots of Li/S batteries with pristine and TiO2/GO-coated separators before and after cycling. As shown in Figure 8a, the charge

Hierarchically structured 3D carbon nanotube electrodes for electrocatalytic applications

• Pei Wang,
• Katarzyna Kulp and
• Michael Bron

Beilstein J. Nanotechnol. 2019, 10, 1475–1487, doi:10.3762/bjnano.10.146

• transfer resistance with respect to the primary CNTs as determined by electrochemical impedance spectroscopy. Thus, we speculate that the improvement in Pt dispersion is due to a better conductivity within the 3D network and a facilitated electron transfer, which may facilitate Pt nucleation at the CNT

BiOCl/TiO₂/diatomite composites with enhanced visible-light photocatalytic activity for the degradation of rhodamine B

• Minlin Ao,
• Kun Liu,
• Xuekun Tang,
• Zishun Li,
• Qian Peng and
• Jing Huang

Beilstein J. Nanotechnol. 2019, 10, 1412–1422, doi:10.3762/bjnano.10.139

• efficiency of the samples, photoluminescence spectroscopy, photocurrent and electrochemical impedance spectroscopy were tested. The recombination rate of photogenerated carriers (electrons and holes) in photocatalysts was characterized by photoluminescence spectra. Generally, the lower the spectral intensity

• internal structure of the material to its surface [48]. BTD shows the most prominent photocurrent density, proving that the carrier recombination rate is low and the lifetime is long, which contributes to the enhancement of photocatalytic activity. Electrochemical impedance spectroscopy (EIS) is one of the

Construction of a 0D/1D composite based on Au nanoparticles/CuBi₂O₄ microrods for efficient visible-light-driven photocatalytic activity

• Weilong Shi,
• Mingyang Li,
• Hongji Ren,
• Feng Guo,
• Xiliu Huang,
• Yu Shi and
• Yubin Tang

Beilstein J. Nanotechnol. 2019, 10, 1360–1367, doi:10.3762/bjnano.10.134

• photocatalytic activity after three cycles. This decrease of photocatalytic performance is mainly due to the mass of catalysts being inevitably lost in the recycling process [39]. Photocurrent response and electrochemical impedance spectroscopy (EIS) measurements were carried out to obtain some insights into the