Photocatalytic methane oxidation over a TiO₂/SiNWs p–n junction catalyst at room temperature

• Qui Thanh Hoai Ta,
• Luan Minh Nguyen,
• Ngoc Hoi Nguyen,
• Phan Khanh Thinh Nguyen and
• Dai Hai Nguyen

Beilstein J. Nanotechnol. 2024, 15, 1132–1141, doi:10.3762/bjnano.15.92

• forces generated charge carriers to move in opposite directions and suppresses charge recombination. Besides, surface morphology and optical properties of the the p–n TiO2/SiNWs catalyst are also beneficial for the photocatalytic activity. It is expected that the results of this study will provide

• well prepared with an average length of 4 µm. Moreover, the surface of the SiNWs was fully decorated by the TiO2 passivation layer and became blurry. The active pure 25 nm TiO2 layer exhibits flake-like morphology as displayed in Figure 2c,d. Optical properties Nanowire arrays offer a better optical

Effect of wavelength and liquid on formation of Ag, Au, Ag/Au nanoparticles via picosecond laser ablation and SERS-based detection of DMMP

• Sree Satya Bharati Moram,
• Chandu Byram and
• Venugopal Rao Soma

Beilstein J. Nanotechnol. 2024, 15, 1054–1069, doi:10.3762/bjnano.15.86

• , and aggregation variations, ultimately impacting their optical properties [53]. Also, from absorbance studies, it is observed that the ablation rate is higher for the Au target than for Ag because of the hardness variation observed in an earlier report by Solati et al. [54]. In another study by Bae et

Intermixing of MoS₂ and WS₂ photocatalysts toward methylene blue photodegradation

• Maryam Al Qaydi,
• Nitul S. Rajput,
• Michael Lejeune,
• Abdellatif Bouchalkha,
• Mimoun El Marssi,
• Steevy Cordette,
• Chaouki Kasmi and
• Mustapha Jouiad

Beilstein J. Nanotechnol. 2024, 15, 817–829, doi:10.3762/bjnano.15.68

• ) equipped with a monochromatic and microfocused Al Kα X-ray source (1486.6 eV). During the experiment, an E-neutralizer (1 V) was implemented. The XPS spectra were calibrated using the C 1s peak position at 284.6 eV as a reference. The CasaXPS software was subsequently used for data processing. The optical

• properties and photodegradation experiments were conducted on a UV–vis–near IR spectrometer (JASCO V-670) and using solar simulator excitation for the PD monitoring using 10 mL of MB dye solution with a concentration of 5 mg/L (10−5 M) and 1 mg of exfoliated photocatalyst. The intensity of the optical

Green synthesis of biomass-derived carbon quantum dots for photocatalytic degradation of methylene blue

• Dalia Chávez-García,
• Mario Guzman,
• Viridiana Sanchez and
• Rubén D. Cadena-Nava

Beilstein J. Nanotechnol. 2024, 15, 755–766, doi:10.3762/bjnano.15.63

• activity of the CQDs in degrading methylene blue was evaluated under both sunlight and incandescent light irradiation, with measurements taken at 20 min intervals over a 2 h period. The CQDs, with sizes ranging from 1–10 nm, demonstrated notable optical properties, including upconversion and down

Aero-ZnS prepared by physical vapor transport on three-dimensional networks of sacrificial ZnO microtetrapods

• Veaceslav Ursaki,
• Tudor Braniste,
• Victor Zalamai,
• Emil Rusu,
• Vladimir Ciobanu,
• Vadim Morari,
• Daniel Podgornii,
• Pier Carlo Ricci,
• Rainer Adelung and
• Ion Tiginyanu

Beilstein J. Nanotechnol. 2024, 15, 490–499, doi:10.3762/bjnano.15.44

• the phases is demonstrated by the narrow lines in the XRD pattern, while their good optical properties are indicated by the presence of the near-bandgap emission and the narrow lines of resonant Raman scattering. In spite of the good crystalline quality, emission bands related to donor and acceptor

Photocatalytic degradation of methylene blue under visible light by cobalt ferrite nanoparticles/graphene quantum dots

• Vo Chau Ngoc Anh,
• Le Thi Thanh Nhi,
• Le Thi Kim Dung,
• Dang Thi Ngoc Hoa,
• Nguyen Truong Son,
• Nguyen Thi Thao Uyen,
• Nguyen Ngoc Uyen Thu,
• Le Van Thanh Son,
• Le Trung Hieu,
• Tran Ngoc Tuyen and
• Dinh Quang Khieu

Beilstein J. Nanotechnol. 2024, 15, 475–489, doi:10.3762/bjnano.15.43

• /GQDs-200 after thermal hydrolysis was filtered by centrifuging and divided into two parts, that is, solution and solid. The optical properties of the solution are shown in Figure 2a. The inset in Figure 2a presents the 100 mL beaker containing the GQD solution. The sample on the left was exposed to

On the mechanism of piezoresistance in nanocrystalline graphite

• Sandeep Kumar,
• Simone Dehm and
• Ralph Krupke

Beilstein J. Nanotechnol. 2024, 15, 376–384, doi:10.3762/bjnano.15.34

• , which was constructed in-house and automated using Python. Then, sheet resistance measurements under externally applied strain are discussed. Raman spectroscopy of the NCG under strain is studied, which gives insights into the distribution of strain in the film. Utilizing electrical and optical

• properties, a mechanism for piezoresistance in NCG is proposed. The work included here is a part of the PhD thesis completed by the first author S. Kumar [23]. Results and Discussion The two-point bending fixture, which was constructed to impart external strain and simultaneously perform sheet resistance

Controllable physicochemical properties of WO_x thin films grown under glancing angle

• Rupam Mandal,
• Aparajita Mandal,
• Alapan Dutta,
• Rengasamy Sivakumar,
• Sanjeev Kumar Srivastava and
• Tapobrata Som

Beilstein J. Nanotechnol. 2024, 15, 350–359, doi:10.3762/bjnano.15.31

• the AFM and SEM analysis, henceforth, the films will be referred to as NS-WOx films. Regarding the optical properties, the transmittance spectra of the as-deposited NS-WOx films on glass show the highest transmittance (more than 90%) over the spectral range of 300 to 1200 nm for 6 nm films, which

• . Overall, the detailed study exploring a wide range of tunability regarding electrical and optical properties in WOx films as functions of the thickness points towards its importance for various device applications including electrochromic devices, RRAM, and LEDs, and even in designing carrier-selective

Comparative electron microscopy particle sizing of TiO₂ pigments: sample preparation and measurement

• Ralf Theissmann,
• Christopher Drury,
• Markus Rohe,
• Thomas Koch,
• Jochen Winkler and
• Petr Pikal

Beilstein J. Nanotechnol. 2024, 15, 317–332, doi:10.3762/bjnano.15.29

• dioxide materials, the optical properties of E171 are related to the primary particle size, although the degree of dispersion needs to be taken into account [12]. An overview of particle size measurement methods for nanomaterials is given in [4]. Our paper focuses mainly on number-based particle size

• measurements for E171 using EM investigations and the comparison with optical properties, SSA, and single-particle inductively coupled mass spectrometry (spICP-MS) to accompany the reported EM results. An overview covering industrially applied measurement methods for pigments and fillers is given in the JRC

• log-normal assumption. The probability p that the particle size distribution is not log-normal is given in Table 2 together with the results of the fits. Indirect particle size measurements and optical properties Single-particle inductively coupled plasma mass spectrometry (spICP-MS) measurements are

Determining by Raman spectroscopy the average thickness and N-layer-specific surface coverages of MoS₂ thin films with domains much smaller than the laser spot size

• Felipe Wasem Klein,
• Jean-Roch Huntzinger,
• Vincent Astié,
• Damien Voiry,
• Romain Parret,
• Houssine Makhlouf,
• Sandrine Juillaguet,
• Jean-Manuel Decams,
• Sylvie Contreras,
• Périne Landois,
• Ahmed-Azmi Zahab,
• Jean-Louis Sauvajol and
• Matthieu Paillet

Beilstein J. Nanotechnol. 2024, 15, 279–296, doi:10.3762/bjnano.15.26

• transition to a direct bandgap semiconductor with very high photoluminescence quantum yield when thinned down to a monolayer [13][14][15][16][17]. Its unique electronic and optical properties could provide an edge in many future applications. The multilayers MoS2 structures are of the most common 2Hc type

In situ optical sub-wavelength thickness control of porous anodic aluminum oxide

• Aleksandrs Dutovs,
• Raimonds Popļausks,
• Oskars Putāns,
• Vladislavs Perkanuks,
• Aušrinė Jurkevičiūtė,
• Tomas Tamulevičius,
• Uldis Malinovskis,
• Iryna Olyshevets,
• Donats Erts and
• Juris Prikulis

Beilstein J. Nanotechnol. 2024, 15, 126–133, doi:10.3762/bjnano.15.12

• software (SEA, v1.3.8, Semilab). The optical model is depicted in Figure 1c. The substrate is aluminum, phase 1 represents the barrier layer and is aluminum oxide, phase 2 represents PAAO and is a mixture of air and aluminum oxide, and ambient is air. The optical properties of all materials were available

Curcumin-loaded nanostructured systems for treatment of leishmaniasis: a review

• Douglas Dourado,
• Thayse Silva Medeiros,
• Éverton do Nascimento Alencar,
• Edijane Matos Sales and
• Fábio Rocha Formiga

Beilstein J. Nanotechnol. 2024, 15, 37–50, doi:10.3762/bjnano.15.4

• , assembly, and optical properties [113]. These nanoformulations can be synthesized through chemical, physical, or biological processes and are solely generated from metal precursors such as silver and gold [114][115]. In addition, MNPs have been widely used in therapy, drug delivery, targeting, and imaging

A visible-light photodetector based on heterojunctions between CuO nanoparticles and ZnO nanorods

• Doan Nhat Giang,
• Nhat Minh Nguyen,
• Duc Anh Ngo,
• Thanh Trang Tran,
• Le Thai Duy,
• Cong Khanh Tran,
• Thi Thanh Van Tran,
• Phan Phuong Ha La and
• Vinh Quang Dang

Beilstein J. Nanotechnol. 2023, 14, 1018–1027, doi:10.3762/bjnano.14.84

• composition of the materials. The morphology of pure CuO NPs and CuO NPs/ZnO NRs was examined by field-emission scanning electron microscopy. UV–vis absorption spectroscopy showed the optical properties of the materials. The photodetector performance was studied through the current–voltage (I–V

Nanoarchitectonics of photothermal materials to enhance the sensitivity of lateral flow assays

• Elangovan Sarathkumar,
• Rajasekharan S. Anjana and
• Ramapurath S. Jayasree

Beilstein J. Nanotechnol. 2023, 14, 988–1003, doi:10.3762/bjnano.14.82

• maintained. Further, the development of a laser readout system to measure the signal intensity of the test line could potentially bring out the characteristic feature of POCT [10]. To establish a correlation between the nanoscale architecture and the optical properties of materials in order to enhance the

• higher cross-sectional area. The PCE of the gold nanoshells can be increased by either increasing the core-to-shell radius ratio or by increasing their aspect ratio [58][59]. In a theoretical study, the size-dependent optical properties of three different nanomaterials, including gold nanospheres, gold

• [74][76]. Au-based nanocomposites have been widely applied in the field of biosensor development because of their wide absorption and excellent light-to-heat conversion properties. Core–shell nanoparticles have a higher PCE than gold nanospheres [77]. Variations in the optical properties were observed

Isolation of cubic Si₃P₄ in the form of nanocrystals

• Polina K. Nikiforova,
• Sergei S. Bubenov,
• Vadim B. Platonov,
• Andrey S. Kumskov,
• Nikolay N. Kononov,
• Tatyana A. Kuznetsova and
• Sergey G. Dorofeev

Beilstein J. Nanotechnol. 2023, 14, 971–979, doi:10.3762/bjnano.14.80

• . Several techniques for functionalization and colloidal solubilization of Si3P4 NPs were outlined. Optical properties of the material were studied to reveal an experimental bandgap of 1.25 eV. Potential applications of the material include the preparation of microcircuits through the introduction of P

A graphene quantum dots–glassy carbon electrode-based electrochemical sensor for monitoring malathion

• Sanju Tanwar,
• Aditi Sharma and
• Dhirendra Mathur

Beilstein J. Nanotechnol. 2023, 14, 701–710, doi:10.3762/bjnano.14.56

• obtained, which will be used as an electrochemical nanosensor in further studies for malathion detection (Figure 1). Characterization FTIR, Raman, UV–vis, and fluorescence spectroscopy measurements were carried out to determine the optical properties of GQDs. A Perkin Elmer LAMBDA 750 spectrophotometer was

Metal-organic framework-based nanomaterials as opto-electrochemical sensors for the detection of antibiotics and hormones: A review

• Akeem Adeyemi Oladipo,
• Saba Derakhshan Oskouei and
• Mustafa Gazi

Beilstein J. Nanotechnol. 2023, 14, 631–673, doi:10.3762/bjnano.14.52

• ions. By regulating how many ligands can bind to the metal and in which direction, the coordination preference of the metal, for instance, affects the stability, size, and nature of the formed pores. Electronic and optical properties of MOFs In addition to the physicochemical characteristics of MOFs

Titania nanoparticles for photocatalytic degradation of ethanol under simulated solar light

• Evghenii Goncearenco,
• Iuliana P. Morjan,
• Claudiu Teodor Fleaca,
• Florian Dumitrache,
• Elena Dutu,
• Monica Scarisoreanu,
• Valentin Serban Teodorescu,
• Alexandra Sandulescu,
• Crina Anastasescu and
• Ioan Balint

Beilstein J. Nanotechnol. 2023, 14, 616–630, doi:10.3762/bjnano.14.51

• recombination between free electrons and holes. The optical properties of the TiO2 powders has been investigated by absorbance measurements. Figure 5 presents an example of these measurements of both sample series. In the case of the TiO2 material, it is known that it can have two types of transitions, namely

• donor levels, for example chlorine atoms [66], but most probably they are acceptor levels created by titanium vacancies [67][68]. Band-to-band transitions have not been detected as separate PL bands, taking into account the obtained bandgap values from the optical properties. But, they are surely a part

SERS performance of GaN/Ag substrates fabricated by Ag coating of GaN platforms

• Magdalena A. Zając,
• Bogusław Budner,
• Malwina Liszewska,
• Bartosz Bartosewicz,
• Łukasz Gutowski,
• Jan L. Weyher and
• Bartłomiej J. Jankiewicz

Beilstein J. Nanotechnol. 2023, 14, 552–564, doi:10.3762/bjnano.14.46

• substrates were examined regarding their optical properties using UV–vis spectroscopy and regarding their morphology using scanning electron microscopy. SERS properties of the fabricated GaN/Ag substrates were evaluated by measuring SERS spectra of 4-mercaptobenzoic acid molecules adsorbed on them. For all

• morphology of fabricated Ag layers examined by scanning electron microscopy (SEM). Then, we present the results of their optical properties determined using UV–vis spectroscopy. Finally, we compare the SERS performance of the GaN/Ag substrates toward 4-mercaptobenzoic acid (pMBA) molecules adsorbed on them

• -developed surface is created. Also, with the increase in the temperature of the GaN platforms, the surface of the pillars is less and less covered with Ag, and they look mostly exposed as a result of the growth of even larger Ag nanoparticles. Optical properties of fabricated GaN/Ag substrates The

The origin of black and white coloration of the Asian tiger mosquito Aedes albopictus (Diptera: Culicidae)

• Manuela Rebora,
• Gianandrea Salerno,
• Silvana Piersanti,
• Alexander Kovalev and
• Stanislav N. Gorb

Beilstein J. Nanotechnol. 2023, 14, 496–508, doi:10.3762/bjnano.14.41

• 100 most invasive species in the world being an aggressive day-biting species. It is of high medical importance as a vector of chikungunya virus, dengue virus, and dirofilariasis [18]. Detailed studies regarding the optical properties of the body surface of insects, such as Ae. albopictus can be

Conjugated photothermal materials and structure design for solar steam generation

• Chia-Yang Lin and
• Tsuyoshi Michinobu

Beilstein J. Nanotechnol. 2023, 14, 454–466, doi:10.3762/bjnano.14.36

• evaporator (Figure 12d–f). Conclusion In this review, we presented the recent progress and important contributions regarding conjugated photothermal materials used in the SSG process, such as pyrrole derivatives, PANI, PPy, and PDA. Conjugated molecules can be designed to tailor the optical properties and

Plasmonic nanotechnology for photothermal applications – an evaluation

• A. R. Indhu,
• L. Keerthana and
• Gnanaprakash Dharmalingam

Beilstein J. Nanotechnol. 2023, 14, 380–419, doi:10.3762/bjnano.14.33

• in this study can still be important for the assessment of optical properties. In this study the conclusion that all particles become increasing scatterers with size (from 10 to 50 nm), with an analogous trend in the maximal temperature increase of the nanoparticles, was made. The larger nanospheres

Bismuth-based nanostructured photocatalysts for the remediation of antibiotics and organic dyes

• Akeem Adeyemi Oladipo and
• Faisal Suleiman Mustafa

Beilstein J. Nanotechnol. 2023, 14, 291–321, doi:10.3762/bjnano.14.26

• static electric field, which effectively aids in the separation and transfer of photogenerated carriers. Bulk Bi and Bi-based nanostructure morphologies can also be easily altered using a variety of synthesis techniques due to their unique electrical and optical properties, which are directly tied to the

• visible in Bi nanowires with a diameter of around 1–3 nm, but as the diameter increased, they became less visible because of the intense quantum confinement effect. In addition to the electronic properties of Bi, its outstanding optical properties have a big impact on how effective it is as a

• photocatalyst. Bulk Bi exhibits high interband electronic transition rates that result in a negative ultraviolet–visible permittivity and a large infrared refractive index. Numerous investigations have shown that the quantum confinement effect affects the optical properties of Bi [25][71][72][73][74][75][76][77

Structural, optical, and bioimaging characterization of carbon quantum dots solvothermally synthesized from o-phenylenediamine

• Zoran M. Marković,
• Milica D. Budimir,
• Martin Danko,
• Dušan D. Milivojević,
• Pavel Kubat,
• Danica Z. Zmejkoski,
• Vladimir B. Pavlović,
• Marija M. Mojsin,
• Milena J. Stevanović and
• Biljana M. Todorović Marković

Beilstein J. Nanotechnol. 2023, 14, 165–174, doi:10.3762/bjnano.14.17

• characterization methods (AFM, TEM, EDS, FTIR, photoluminescence, and EPR) indicate the significant influence of the precursor on structural, chemical, and optical properties. Antibacterial and cytotoxicity tests showed that these dots did not have any antibacterial potential, because of the low extent of reactive

• nm (Figure S1c,d in Supporting Information File 1). Figure 1 shows the surface morphology of neat PU and a CQDs/PU sample. The RMS roughness values of these samples are 4.45 and 14.04 nm, respectively. FTIR, UV–vis, and PL spectra of CQDs and CQDs/PU To study the chemical and optical properties of

Formation of nanoflowers: Au and Ni silicide cores surrounded by SiO_x branches

• Feitao Li,
• Siyao Wan,
• Dong Wang and
• Peter Schaaf

Beilstein J. Nanotechnol. 2023, 14, 133–140, doi:10.3762/bjnano.14.14

• instance, alloyed AuAg nanoparticles show a tunable LSPR peak by changing the Au/Ag ratio [30]. Also, through the leaching of the less noble element, such as Ag in AuAg nanoparticles, dealloying can yield porous Au nanosponges with excellent optical properties [31][32][33][34][35]. Thus, it is interesting