Pull-off and friction forces of micropatterned elastomers on soft substrates: the effects of pattern length scale and stiffness

• Peter van Assenbergh,
• Marike Fokker,
• Julian Langowski,
• Jan van Esch,
• Marleen Kamperman and
• Dimitra Dodou

Beilstein J. Nanotechnol. 2019, 10, 79–94, doi:10.3762/bjnano.10.8

• cycles. PVA subjected to two and three freeze–thaw cycles had storage moduli of 12 kPa (referred to as PVA-12) and 18 kPa (referred to as PVA-18), respectively, as measured using a rheometer (see section 1 of Supporting Information File 1). The dissipation factor tan δ was 0.05 and 0.07 for PVA-12 and

• the micropattern. The PVA substrates have some dissipative properties (dissipation factors of PVA-12: tan δ = 0.05; PVA-18: tan δ = 0.07), which might contribute to the resultant pull-off force as well. Given the low value of these dissipation factors, we doubt whether damping plays a significant role

Femtosecond laser-assisted fabrication of chalcopyrite micro-concentrator photovoltaics

• Franziska Ringleb,
• Stefan Andree,
• Berit Heidmann,
• Jörn Bonse,
• Katharina Eylers,
• Owen Ernst,
• Torsten Boeck,
• Martina Schmid and
• Jörg Krüger

Beilstein J. Nanotechnol. 2018, 9, 3025–3038, doi:10.3762/bjnano.9.281

• concentrator cells both scale with the cell size, flat-plate-like weight and form factors can be realized by downsizing classical CPV to the microscale. Since the amount of heat, which is concentrated on each cell, is lower than for macroscopic concentrators, the system has a better heat dissipation, which has

• absorber area only and the design will benefit from improved heat dissipation. A further enhancement can thus be expected in the final device. In the configuration investigated here, the highest efficiencies were 3.06% at 3 suns for CISe microcells from the nucleation approach, corresponding to a relative

Friction reduction through biologically inspired scale-like laser surface textures

• Johannes Schneider,
• Vergil Djamiykov and
• Christian Greiner

Beilstein J. Nanotechnol. 2018, 9, 2561–2572, doi:10.3762/bjnano.9.238

• elaborate fluid dynamics simulations. As far as the unlubricated experiments are concerned, the concept developed by Bowden and Tabor [51] points out that most frictional energy dissipation is due to plastic deformation of the subsurface layer. If one of the sliding partners is harder than the other, the

Effective sensor properties and sensitivity considerations of a dynamic co-resonantly coupled cantilever sensor

• Julia Körner

Beilstein J. Nanotechnol. 2018, 9, 2546–2560, doi:10.3762/bjnano.9.237

• co-resonantly coupled system, the definition based on energy dissipation will be used, hence: with Ea,b denoting the total energy stored in the system and ΔEa,b the dissipated energy per oscillation period. Please note that the absolute value for the dissipated energy (often considered with a

Influence of the thickness of an antiferromagnetic IrMn layer on the static and dynamic magnetization of weakly coupled CoFeB/IrMn/CoFeB trilayers

• Deepika Jhajhria,
• Dinesh K. Pandya and
• Sujeet Chaudhary

Beilstein J. Nanotechnol. 2018, 9, 2198–2208, doi:10.3762/bjnano.9.206

• trilayers, the spin angular momentum can experience an additional damping dissipation at the FM/AF interface resulting from the direct exchange coupling between FM and AF layers [29], which in our case is minimal as evidenced by the absence of exchange bias at room temperature (discussed below). So, the

Dumbbell gold nanoparticle dimer antennas with advanced optical properties

• Janning F. Herrmann and
• Christiane Höppener

Beilstein J. Nanotechnol. 2018, 9, 2188–2197, doi:10.3762/bjnano.9.205

• decreasing distance, the influence of the electromagnetic field enhancement is counterbalanced by non-radiative transitions to electronic states of the metallic interface and sequential dissipation of the excited state energy. Therefore, for small AuNP-dye distances the spontaneous emission starts to decline

Fabrication of photothermally active poly(vinyl alcohol) films with gold nanostars for antibacterial applications

• Mykola Borzenkov,
• Maria Moros,
• Claudia Tortiglione,
• Serena Bertoldi,
• Nicola Contessi,
• Silvia Faré,
• Angelo Taglietti,
• Agnese D’Agostino,
• Piersandro Pallavicini,
• Maddalena Collini and
• Giuseppe Chirico

Beilstein J. Nanotechnol. 2018, 9, 2040–2048, doi:10.3762/bjnano.9.193

• under irradiation at all three aforementioned laser wavelengths, as shown in Figure 4. The large increase in temperature that is induced by the PVA-GNS films under NIR irradiation in comparison with aqueous GNS solutions [3] can be explained by the reduction of the thermal dissipation from the water

Metal-free catalysis based on nitrogen-doped carbon nanomaterials: a photoelectron spectroscopy point of view

• Mattia Scardamaglia and
• Carla Bittencourt

Beilstein J. Nanotechnol. 2018, 9, 2015–2031, doi:10.3762/bjnano.9.191

• kinetic energies from hundreds of electronvolts to few kiloelectronvolts does not lead to a damage or the sputtering of the material [37][57][84][85]. This effect was explained with different dissipation of the ion energy in the nanostructured material compared to the bulk. In the former, many ions

Recent highlights in nanoscale and mesoscale friction

• Andrea Vanossi,
• Dirk Dietzel,
• Andre Schirmeisen,
• Ernst Meyer,
• Rémy Pawlak,
• Thilo Glatzel,
• Marcin Kisiel,
• Shigeki Kawai and
• Nicola Manini

Beilstein J. Nanotechnol. 2018, 9, 1995–2014, doi:10.3762/bjnano.9.190

• ” research field is leading to new technological advances in the area of engineering and materials science. Keywords: atomic force microscopy; dissipation; friction; mesoscale; nanomanipulation; nanoscale; scale bridging; structural lubricity; superlubricity; Introduction Friction, the force that resists

• the relative lateral motion of bodies in contact, and the related dissipation phenomena are being investigated extensively due to their importance in applications, from everyday life to advanced technology. At the macroscopic scale, friction between sliding bodies depends on their surface roughness

• level, another important achievement of these ion-crystal systems in an optical lattice consists in the capability to span essentially five orders of magnitude in sliding speed. This is achieved while maintaining a full control of dissipation and temperature, thus emulating perfectly the Prandtl

Electromigrated electrical optical antennas for transducing electrons and photons at the nanoscale

• Arindam Dasgupta,
• Mickaël Buret,
• Nicolas Cazier,
• Marie-Maxime Mennemanteuil,
• Reinaldo Chacon,
• Kamal Hammani,
• Jean-Claude Weeber,
• Juan Arocas,
• Laurent Markey,
• Gérard Colas des Francs,
• Alexander Uskov,
• Igor Smetanin and
• Alexandre Bouhelier

Beilstein J. Nanotechnol. 2018, 9, 1964–1976, doi:10.3762/bjnano.9.187

• fairly constant because Joule dissipation is not yet affecting the temperature-dependent resistivity of gold. On increasing Vdc, the temperature of the constriction grows and the conductance starts to fluctuate. The general trend is that G(t) decreases when stepping up Vdc. We also consistently observe a

• momentary rise of the conductance, which we attribute to the desorption of surface contaminants as well as a temperature annealing of the constriction due to dissipation of the electrical power in this area. This effect can be traced in Figure 2a at around t = 150 s. An example of another temperature effect

• are two reasons why the formation of the gap is not occurring at the constriction. First, the dissipation of electrical power during the process takes place at the constriction, i.e., at the region of highest resistance [38]. The evaporated Au layer can thus be partially annealed through Joule heating

Tunable fractional Fourier transform implementation of electronic wave functions in atomically thin materials

• Daniela Dragoman

Beilstein J. Nanotechnol. 2018, 9, 1828–1833, doi:10.3762/bjnano.9.174

• computer architectures based on CMOS technology are reaching their limits of integration that emerge due to several problems, including those related to the increase in the number of interconnects and to heat dissipation [1][2]. Several alternatives, such as quantum computing [3], have been proposed and

• some problems associated with classical computing circuits, in particular with the irreversible nature of their logic operations. For instance, logic architectures employing reversible gates based on an as small as possible number of elements/transistors could minimize the heat dissipation problem

Toward the use of CVD-grown MoS₂ nanosheets as field-emission source

• Geetanjali Deokar,
• Nitul S. Rajput,
• Junjie Li,
• Francis Leonard Deepak,
• Wei Ou-Yang,
• Nicolas Reckinger,
• Carla Bittencourt,
• Jean-Francois Colomer and
• Mustapha Jouiad

Beilstein J. Nanotechnol. 2018, 9, 1686–1694, doi:10.3762/bjnano.9.160

• densely packed NSs might be playing an important role to achieve high current density and faster heat dissipation, thereby reducing the burning out of active emission sites induced by Joule heating. The as-grown NSs could also possibly be used as heat dissipating nano-channels in FE or electronic devices

Optical near-field mapping of plasmonic nanostructures prepared by nanosphere lithography

• Gitanjali Kolhatkar,
• Alexandre Merlen,
• Jiawei Zhang,
• Chahinez Dab,
• Gregory Q. Wallace,
• François Lagugné-Labarthet and
• Andreas Ruediger

Beilstein J. Nanotechnol. 2018, 9, 1536–1543, doi:10.3762/bjnano.9.144

• , which is ascribed to different reasons: for one, the experimental radii of the apexes might be larger than in the numerical model, or the crystallinity of the gold composing the nanotriangles might be less than ideal thus causing dissipation. Also, the simulation assumes perfectly crystalline gold. In

Electrostatically actuated encased cantilevers

• Benoit X. E. Desbiolles,
• Gabriela Furlan,
• Adam M. Schwartzberg,
• Paul D. Ashby and
• Dominik Ziegler

Beilstein J. Nanotechnol. 2018, 9, 1381–1389, doi:10.3762/bjnano.9.130

• immersed in a viscous fluid. Quantitative measurements of stiffness, energy dissipation and tip–sample interactions using dynamic force sensors remain challenging due to spurious resonances of the system. Results: We demonstrate for the first time electrostatic actuation with a built-in electrode. Solely

Disorder-induced suppression of the zero-bias conductance peak splitting in topological superconducting nanowires

• Jun-Tong Ren,
• Hai-Feng Lü,
• Sha-Sha Ke,
• Yong Guo and
• Huai-Wu Zhang

Beilstein J. Nanotechnol. 2018, 9, 1358–1369, doi:10.3762/bjnano.9.128

• = 0.6 μm, it is found that all three types of disorder can suppress the amplitude of the conductance peak and broaden the peak width to some different extent. The presence of disorder in the system leads to a similar result induced by dissipation or finite temperature, both of which can lower the peak

Artifacts in time-resolved Kelvin probe force microscopy

• Sascha Sadewasser,
• Nicoleta Nicoara and
• Santiago D. Solares

Beilstein J. Nanotechnol. 2018, 9, 1272–1281, doi:10.3762/bjnano.9.119

• with the so-called dissipation KPFM mode [31][32]. It is also important to note that the artifacts in time-resolved KPFM observed in Figure 4 and Figure 5 have a different origin from one another. In the latter case, a direct interference of the applied bias or light pulses with the cantilever

A novel copper precursor for electron beam induced deposition

• Caspar Haverkamp,
• George Sarau,
• Mikhail N. Polyakov,
• Ivo Utke,
• Marcos V. Puydinger dos Santos,
• Silke Christiansen and
• Katja Höflich

Beilstein J. Nanotechnol. 2018, 9, 1220–1227, doi:10.3762/bjnano.9.113

• ). Electrical measurements were performed at room temperature using a conventional four-probe setup with a Keithley 2400 source meter. The power dissipation on the deposits was limited to 1 nW to avoid self-heating and changes in atomic composition. The current voltage curve is provided in Supporting

Imaging of viscoelastic soft matter with small indentation using higher eigenmodes in single-eigenmode amplitude-modulation atomic force microscopy

• Miead Nikfarjam,
• Enrique A. López-Guerra,
• Santiago D. Solares and
• Babak Eslami

Beilstein J. Nanotechnol. 2018, 9, 1116–1122, doi:10.3762/bjnano.9.103

• ). At this extreme, no energy dissipation takes place and the material behaves in a soft-elastic manner [11][15][16][17]. On the other hand, when the material is probed at extremely high loading rates, the dashpots do not deform and the behavior of the mechanical model is ruled by the summation of all

Magnetic characterization of cobalt nanowires and square nanorings fabricated by focused electron beam induced deposition

• Federico Venturi,
• Gian Carlo Gazzadi,
• Amir H. Tavabi,
• Alberto Rota,
• Rafal E. Dunin-Borkowski and
• Stefano Frabboni

Beilstein J. Nanotechnol. 2018, 9, 1040–1049, doi:10.3762/bjnano.9.97

• literature data [33][34]. The slightly higher Co content for depositions at lower energy can be interpreted as a thermal effect resulting from power dissipation of the primary beam closer to the surface [35]. Furthermore, the 5 keV depositions are wider than the 15 keV depositions, resulting in a larger

Electro-optical interfacial effects on a graphene/π-conjugated organic semiconductor hybrid system

• Karolline A. S. Araujo,
• Luiz A. Cury,
• Matheus J. S. Matos,
• Thales F. D. Fernandes,
• Luiz G. Cançado and
• Bernardo R. A. Neves

Beilstein J. Nanotechnol. 2018, 9, 963–974, doi:10.3762/bjnano.9.90

• peak force or tapping mode. Besides conventional topographic images, peak force mode yields several concomitant images which map mechanical properties of the sample, like adhesion, elastic modulus, dissipation and others [64]. The adhesion channel monitors tip–sample attractive forces along the imaging

Scanning speed phenomenon in contact-resonance atomic force microscopy

• Christopher C. Glover,
• Jason P. Killgore and
• Ryan C. Tung

Beilstein J. Nanotechnol. 2018, 9, 945–952, doi:10.3762/bjnano.9.87

• be approximately 1 nm in thickness and formed at approximately 40% RH on mica [26][27]. The water film was found to have elastic, viscous, and energy dissipation properties that changed when the driving amplitude was varied [30][33][34]. Hofbauer et al. found that “the mechanical stress exerted by

Tuning adhesion forces between functionalized gold colloidal nanoparticles and silicon AFM tips: role of ligands and capillary forces

• Sven Oras,
• Sergei Vlassov,
• Marta Berholts,
• Rünno Lõhmus and
• Karine Mougin

Beilstein J. Nanotechnol. 2018, 9, 660–670, doi:10.3762/bjnano.9.61

• ) self-assemble on a surface with rather a poor packing [2]. This kind of structuration leads to low density of molecules on the surface. As a result, short chains have more structural disorder and defects that promote energy dissipation through rotational and vibrational excitation modes [30]. These

• between tip and sample surface, Young’s modulus (according to either DMT or Sneddon model), deformation and energy dissipation along with the surface topography (Supporting Information File 1). Etched silicon probes RTESPA-300 with a nominal spring constant k ≈ 40 N/m for QNM were provided by Bruker. All

Electron interactions with the heteronuclear carbonyl precursor H₂FeRu₃(CO)₁₃ and comparison with HFeCo₃(CO)₁₂: from fundamental gas phase and surface science studies to focused electron beam induced deposition

• Ragesh Kumar T P,
• Paul Weirich,
• Lukas Hrachowina,
• Marc Hanefeld,
• Ragnar Bjornsson,
• Helgi Rafn Hrodmarsson,
• Sven Barth,
• D. Howard Fairbrother,
• Michael Huth and
• Oddur Ingólfsson

Beilstein J. Nanotechnol. 2018, 9, 555–579, doi:10.3762/bjnano.9.53

• process proceeding directly along a repulsive path on the respective potential energy surface of the ground state anion. For H2FeRu3(CO)13, on the other hand, energy dissipation is more effective leading to more apparent competition between the apex loss and base plane fragmentation of the ground state

Review: Electrostatically actuated nanobeam-based nanoelectromechanical switches – materials solutions and operational conditions

• Liga Jasulaneca,
• Jelena Kosmaca,
• Raimonds Meija,
• Jana Andzane and
• Donats Erts

Beilstein J. Nanotechnol. 2018, 9, 271–300, doi:10.3762/bjnano.9.29

• conductivity [10][96][99]. If there is a low current density in the contact (in the range of 1 pA/nm2) and a good thermal contact, the temperature changes modestly (ΔT < 30 K) and almost no Joule heating occurs [10]. However, even at current densities as low as 3 pA/nm2, energy dissipation in the contact may

Combined scanning probe electronic and thermal characterization of an indium arsenide nanowire

• Tino Wagner,
• Fabian Menges,
• Heike Riel,
• Bernd Gotsmann and
• Andreas Stemmer

Beilstein J. Nanotechnol. 2018, 9, 129–136, doi:10.3762/bjnano.9.15

• length scale of only a few nanometres. At the same time, Joule dissipation affects devices as they are scaled down, and the increasing power densities require adequate thermal management to avoid performance degradation or failure [1]. Hot spots can appear due to increased local energy dissipation at

• between. Temperature profiles along the centre of the wire at different average power dissipation are shown in Figure 1c. For a homogenously Joule-heated one-dimensional conductor between two heat-sinking electrodes, the heat diffusion equation predicts a parabolic or bell-shaped temperature profile [24