Investigation of Hf/Ti bilayers for the development of transition-edge sensor microcalorimeters

• Victoria Y. Safonova,
• Anna V. Gordeeva,
• Anton V. Blagodatkin,
• Dmitry A. Pimanov,
• Anton A. Yablokov and
• Andrey L. Pankratov

Beilstein J. Nanotechnol. 2024, 15, 1353–1361, doi:10.3762/bjnano.15.108

• Academy of Sciences, Akademicheskaya Street, 7, Nizhny Novgorod, Russia, 603950, Russia 10.3762/bjnano.15.108 Abstract The superconducting properties of 85 nm thick hafnium thin films with a 5 nm thick titanium layer on top have been investigated for three different geometries, that is, a film covering

• is possible to fabricate microcalorimeters with δE less than 1 eV using these films. Keywords: hafnium; microcalorimeter; neutrino; superconducting transition width; superconductivity; TES; Introduction Over the last two decades, cryogenic microcalorimeters have found applications in various fields

• ongoing, and the choice of a superconductor material plays an important role here [6][7]. An increase in sensitivity can be achieved by lowering the critical temperature TC below 100 mK. A known solution is two- or multilayer films of various superconductors and normal metals to suppress the transition

Mn-doped ZnO nanopowders prepared by sol–gel and microwave-assisted sol–gel methods and their photocatalytic properties

• Cristina Maria Vlăduț,
• Crina Anastasescu,
• Silviu Preda,
• Oana Catalina Mocioiu,
• Simona Petrescu,
• Jeanina Pandele-Cusu,
• Dana Culita,
• Veronica Bratan,
• Ioan Balint and
• Maria Zaharescu

Beilstein J. Nanotechnol. 2024, 15, 1283–1296, doi:10.3762/bjnano.15.104

• -efficient than conventional heating methods [12][13][14]. This approach is particularly advantageous in technology applications, as it significantly reduces reaction times from days to mere hours or minutes and enables the production of nanocrystalline oxides in the form of powders and films on various

• of amorphous oxide nanopowders, the precipitation of nanocrystalline metal oxides, and the drying and thermal treatment of oxide films [23]. However, there has been comparatively less focus on studying chemical reactions in sol–gel solutions under microwave irradiation [24][25][26][27]. Numerous

• previous studies, the authors demonstrated that Mn-doped ZnO films exhibit superior optical and piezoelectric properties compared to undoped ZnO, with a more compact microstructure and reduced surface roughness [41]. Building on this foundation, the current article aims to focus on the methods of

New design of operational MEMS bridges for measurements of properties of FEBID-based nanostructures

• Bartosz Pruchnik,
• Krzysztof Kwoka,
• Ewelina Gacka,
• Dominik Badura,
• Piotr Kunicki,
• Andrzej Sierakowski,
• Paweł Janus,
• Tomasz Piasecki and
• Teodor Gotszalk

Beilstein J. Nanotechnol. 2024, 15, 1273–1282, doi:10.3762/bjnano.15.103

• stresses in thin films by deflecting a cantilever of defined size from a uniform membrane. We see a need for such experiments for future improvement of our proposed RoI spacing tuning method. The proposed approach allowed us to evaluate the leakage currents separately from the nanodevice properties. It was

The role of a tantalum interlayer in enhancing the properties of Fe₃O₄ thin films

• Hai Dang Ngo,
• Vo Doan Thanh Truong,
• Van Qui Le,
• Hoai Phuong Pham and
• Thi Kim Hang Pham

Beilstein J. Nanotechnol. 2024, 15, 1253–1259, doi:10.3762/bjnano.15.101

• promising applications. High-quality Fe3O4 thin films are a must to achieve the goals. In this report, Fe3O4 films on different substrates (SiO2/Si(100), MgO(100), and MgO/Ta/SiO2/Si(100)) were fabricated at room temperature with radio-frequency (RF) sputtering and annealed at 450 °C for 2 h. The

• . More importantly, changes in grain size and structure due to the effect of the MgO/Ta buffering layers have a strong impact on saturation magnetization and coercivity of Fe3O4 thin films compared to cases of no or just a single buffering layer. Keywords: buffer layer; Fe3O4; magnetite; RF magnetron

• K [1], as well as its high spin polarization with only one spin at the Fermi level, even at room temperature [2][3][4][5][6]. Fe3O4 thin films are an issue of interest and have extensive applications in Li-ion batteries, spin Seebeck devices, supercapacitors, spin Hall magnetoresistance, and the

A low-kiloelectronvolt focused ion beam strategy for processing low-thermal-conductance materials with nanoampere currents

• Annalena Wolff,
• Nico Klingner,
• William Thompson,
• Yinghong Zhou,
• Jinying Lin and
• Yin Xiao

Beilstein J. Nanotechnol. 2024, 15, 1197–1207, doi:10.3762/bjnano.15.97

• different ion species, which are becoming more popular now, especially the lighter ion species where the assumption of a flat disc may not hold. Allen et al. showed that He ions can be beneficial when working with thin films [28] as they mostly transmit through the sample. The ion beam-induced heat for

Photocatalytic methane oxidation over a TiO₂/SiNWs p–n junction catalyst at room temperature

• Qui Thanh Hoai Ta,
• Luan Minh Nguyen,
• Ngoc Hoi Nguyen,
• Phan Khanh Thinh Nguyen and
• Dai Hai Nguyen

Beilstein J. Nanotechnol. 2024, 15, 1132–1141, doi:10.3762/bjnano.15.92

• tools is extremely essential and important [37][38][39]. Herein, we constructed a robust p–n junction catalyst by atomic layer deposition (ALD) of TiO2 thin films on a p-type SiNW substrate for enhancing the photocatalytic efficiency in CH4 oxidation. Pristine p-Si wafers have limited surface area and

• properties of as-synthesized samples were analyzed using an X-ray diffraction system (XRD, Rigaku, SmartLab) with a 2θ range of 20–80° and a field-emission scanning electron microscope (FE-SEM, Hitachi, S-4700). The absorption properties of the thin films were analyzed using a diffuse reflectance UV–vis

Unveiling the potential of alginate-based nanomaterials in sensing technology and smart delivery applications

• Shakhzodjon Uzokboev,
• Khojimukhammad Akhmadbekov,
• Ra’no Nuritdinova,
• Salah M. Tawfik and
• Yong-Ill Lee

Beilstein J. Nanotechnol. 2024, 15, 1077–1104, doi:10.3762/bjnano.15.88

• 96–77%, these sensors were effectively used to identify a variety of volatile aldehydes in river water samples. It is interesting to note that fluorescent APGF@ZIF-8/CS and APOF@ZIF-8/CS films were developed as disposable, portable methods to remove formaldehyde, acetaldehyde, benzaldehyde, and

• sensor. Another fluorescence-based smart sensor from alginate nanofilms was prepared [122]. Scientists proved that relative humidity could be detected using a guar gum–sodium alginate (GGSA) nanocomposite film. The study found that the fluorescence of biocomposite films under UV light varies at various

Interface properties of nanostructured carbon-coated biological implants: an overview

• Mattia Bartoli,
• Francesca Cardano,
• Erik Piatti,
• Stefania Lettieri,
• Andrea Fin and
• Alberto Tagliaferro

Beilstein J. Nanotechnol. 2024, 15, 1041–1053, doi:10.3762/bjnano.15.85

• response. The mechanisms involved in inflammation related to NDs are not yet clear, but authors suggest that the process is started by serum protein deposition triggering the inflammatory cascade. Moreover, polymeric films containing NDs were optimum substrates for osteoblast proliferation as reported by

• Young’s modulus of 100% and 156%, reaching 60 MPa and 0.52 GPa, respectively, after coating. CNTs are generally used to reinforce the bulk of composite-based implants [136] or added to polymeric films [135]. Interestingly, they can be mixed with hydroxyapatite in order to magnify the compatibility with

• of the superior friction reduction achievable using thin ND films as reported by Blum and co-workers [142]. The authors sintered a 75 µm thick layer of NDs onto an aluminum alloy using a focused laser beam and reached a friction coefficient smaller than 0.2. Similar results can be obtained by using

Beyond biomimicry – next generation applications of bioinspired adhesives from microfluidics to composites

• Dan Sameoto

Beilstein J. Nanotechnol. 2024, 15, 965–976, doi:10.3762/bjnano.15.79

• composites can be found elsewhere [47]; the bending stiffness D is a function of the outer film modulus Ef, the distance between the central axis of those films (defined by the core thickness d and the film thickness t), the modulus of the core Ec, and the width of the composite b. If the “core” is made of

• independent fibers, it can have an effective Ec that is close to zero when in the unadhered state and will, therefore, minimally affect bending stiffness in comparison to two independent thin films of Ef. For the simplified model shown in Figure 8, if Ec ≪ Ef and t ≪ d, then the overall bending stiffness

The effect of age on the attachment ability of stick insects (Phasmatodea)

• Marie Grote,
• Stanislav N. Gorb and
• Thies H. Büscher

Beilstein J. Nanotechnol. 2024, 15, 867–883, doi:10.3762/bjnano.15.72

• the cuticle could yield an appearance similar to a pad coverage by other substances resulting in dark patches in WFM (Figure 8B,H,K). Such patches usually showed no covering films visible in stereomicroscopy (Figure 8A,G) and SEM (Figure 8D,I,J). Scars on the attachment pads (Figure 8L) also appeared

Electrospun polysuccinimide scaffolds containing different salts as potential wound dressing material

• Veronika Pálos,
• Krisztina S. Nagy,
• Rita Pázmány,
• Krisztina Juriga-Tóth,
• Bálint Budavári,
• Judit Domokos,
• Dóra Szabó,
• Ákos Zsembery and
• Angela Jedlovszky-Hajdu

Beilstein J. Nanotechnol. 2024, 15, 781–796, doi:10.3762/bjnano.15.65

• increased, which was also observed by Sim and collaborators in the case of polymer electrolyte films containing LiCF3SO3 [51]. At 1634 cm−1, rising peaks also appeared as the concentration of salts increased. It was presumably the peak corresponding to bending vibration of water, H–O–H (Supporting

• average fiber diameter could also explain this. Another study investigated different inorganic salts (LiCl, MgCl2·6H2O, CaCl2, and AlCl3·6H2O) added to starch/PVA films. They perceived that the salts improved the mechanical properties, and the increasing amount of salts increased the elongation at break

Effect of repeating hydrothermal growth processes and rapid thermal annealing on CuO thin film properties

• Monika Ozga,
• Eunika Zielony,
• Aleksandra Wierzbicka,
• Anna Wolska,
• Marcin Klepka,
• Marek Godlewski,
• Bogdan J. Kowalski and
• Bartłomiej S. Witkowski

Beilstein J. Nanotechnol. 2024, 15, 743–754, doi:10.3762/bjnano.15.62

• and Technology, Wybrzeze Wyspiańskiego 27, 50–370 Wroclaw, Poland 10.3762/bjnano.15.62 Abstract This paper presents an investigation into the influence of repeating cycles of hydrothermal growth processes and rapid thermal annealing (HT+RTA) on the properties of CuO thin films. An innovative

• hydrothermal method ensures homogeneous single-phase films initially. However, their electrical instability and susceptibility to cracking under the influence of temperature have posed a challenge to their utilization in electronic devices. To address this limitation, the HT+RTA procedure has been developed

• , which effectively eliminated the issue. Comprehensive surface analysis confirmed the procedure’s ability to yield continuous films in which the content of organic compounds responsible for the formation of cracks significantly decreases. Structural analysis underscored the achieved improvements in the

Level set simulation of focused ion beam sputtering of a multilayer substrate

• Alexander V. Rumyantsev,
• Nikolai I. Borgardt,
• Roman L. Volkov and
• Yuri A. Chaplygin

Beilstein J. Nanotechnol. 2024, 15, 733–742, doi:10.3762/bjnano.15.61

• multilayer films [8], the patterning of 2D materials [9], or the direct introduction of dopants into a solid-state host through recoil implantation [10]. Examples that rely on ion milling include patterning of magnetic multilayers [11], fabrication of optical metamaterials [12], and modification of

Elastic modulus of β-Ga₂O₃ nanowires measured by resonance and three-point bending techniques

• Annamarija Trausa,
• Sven Oras,
• Sergei Vlassov,
• Mikk Antsov,
• Tauno Tiirats,
• Andreas Kyritsakis,
• Boris Polyakov and
• Edgars Butanovs

Beilstein J. Nanotechnol. 2024, 15, 704–712, doi:10.3762/bjnano.15.58

• , University of Tartu, Nooruse 1, 50411 Tartu, Estonia Estonian Military Academy, Riia 12, 51010 Tartu, Estonia 10.3762/bjnano.15.58 Abstract Due to the recent interest in ultrawide bandgap β-Ga2O3 thin films and nanostructures for various electronics and UV device applications, it is important to understand

AFM-IR investigation of thin PECVD SiO_x films on a polypropylene substrate in the surface-sensitive mode

• Hendrik Müller,
• Hartmut Stadler,
• Teresa de los Arcos,
• Adrian Keller and
• Guido Grundmeier

Beilstein J. Nanotechnol. 2024, 15, 603–611, doi:10.3762/bjnano.15.51

• /bjnano.15.51 Abstract Thin silicon oxide films deposited on a polypropylene substrate by plasma-enhanced chemical vapor deposition were investigated using atomic force microscopy-based infrared (AFM-IR) nanospectroscopy in contact and surface-sensitive mode. The focus of this work is the comparison of

• the different measurement methods (i.e., contact mode and surface-sensitive mode) with respect to the chemical surface sensitivity. The use of the surface-sensitive mode in AFM-IR shows an enormous improvement for the analysis of thin films on the IR-active substrate. As a result, in this mode, the

• signal of the substrate material could be significantly reduced. Even layers that are so thin that they could hardly be measured in the contact mode can be analyzed with the surface-sensitive mode. Keywords: AFM-IR; polypropylene; surface-sensitive mode; silicon oxide; thin films; XPS; Introduction

Cholesterol nanoarchaeosomes for alendronate targeted delivery as an anti-endothelial dysfunction agent

• Horacio Emanuel Jerez,
• Yamila Roxana Simioni,
• Kajal Ghosal,
• Maria Jose Morilla and
• Eder Lilia Romero

Beilstein J. Nanotechnol. 2024, 15, 517–534, doi:10.3762/bjnano.15.46

• that aim, blends of lipids were dissolved in chloroform/methanol 1:1 v/v, and the solvents were rotary-evaporated until complete removal. The lipid films were flushed with N2 and hydrated with Tris buffer (10 mM Tris-HCl buffer pH 7.4 with NaCl 0.9% w/w) to obtain the void nanovesicles or 14 mg/mL ALN

• nanovesicles, RhPE at 0.4 μg per mg of lipids was added to the mixture of lipids, and lipid films were hydrated with Tris buffer as stated above. RhPE was quantified by spectrofluorometry (λex = 561 nm and λem = 580 nm) with an LS55 fluorescence spectrometer (PerkinElmer Inc. MA, USA) upon complete disruption

Superconducting spin valve effect in Co/Pb/Co heterostructures with insulating interlayers

• Andrey A. Kamashev,
• Nadir N. Garif’yanov,
• Aidar A. Validov,
• Vladislav Kataev,
• Alexander S. Osin,
• Yakov V. Fominov and
• Ilgiz A. Garifullin

Beilstein J. Nanotechnol. 2024, 15, 457–464, doi:10.3762/bjnano.15.41

• and Co2, 12 Å/s for Pb, and 1.8 Å/s for Si3N4 films. The final design of the samples is depicted in Figure 1. Based on our previous studies in [33][34][48] we chose the thickness of the AF CoOx layer to be = 3.5 nm. This is optimal to maintain the direction of the magnetization of the Co1 layer up to

Heat-induced morphological changes in silver nanowires deposited on a patterned silicon substrate

• Elyad Damerchi,
• Sven Oras,
• Edgars Butanovs,
• Allar Liivlaid,
• Mikk Antsov,
• Boris Polyakov,
• Annamarija Trausa,
• Veronika Zadin,
• Andreas Kyritsakis,
• Loïc Vidal,
• Karine Mougin,
• Siim Pikker and
• Sergei Vlassov

Beilstein J. Nanotechnol. 2024, 15, 435–446, doi:10.3762/bjnano.15.39

• indium tin oxide (ITO), which currently serves as the industry standard for transparent conductive films, the Ag NW network is significantly more mechanically flexible and offers a broader optical transmittance range that extends well beyond the visible region [13][14]. Another related application of Ag

On the mechanism of piezoresistance in nanocrystalline graphite

• Sandeep Kumar,
• Simone Dehm and
• Ralph Krupke

Beilstein J. Nanotechnol. 2024, 15, 376–384, doi:10.3762/bjnano.15.34

• density of defects in the form of grain boundaries. It holds an advantage over graphene in easily achieving wafer-scale growth with controlled thickness. In this study, we explore the piezoresistivity in thin films of nanocrystalline graphite. Simultaneous measurements of sheet resistance and externally

• . However, a hysteresis is observed between forward and reverse sweeps, indicating that structural changes in the films occur, which are in part irreversible. To gain insights into the strain distribution in the strained NCG, we performed in situ Raman measurements with strain as shown in Figure 3a. The

• tunneling distance, d. The model has been used to explain the piezoresistance for several composite materials [29][30]. Zhao et al. [24] used the model to explain the piezoresistance in nanographene films, although the material is comparable to ours and not a composite material in the original sense. NCG

Controllable physicochemical properties of WO_x thin films grown under glancing angle

• Rupam Mandal,
• Aparajita Mandal,
• Alapan Dutta,
• Rengasamy Sivakumar,
• Sanjeev Kumar Srivastava and
• Tapobrata Som

Beilstein J. Nanotechnol. 2024, 15, 350–359, doi:10.3762/bjnano.15.31

• , Alagappa University, Karaikudi 630 003, India Department of Physics, Indian Institute of Technology Kharagpur, Kharagpur 721 302, India 10.3762/bjnano.15.31 Abstract In this work, various physicochemical properties are investigated in nanostructured WOx thin films prepared by radio-frequency magnetron

• sputtering for optoelectronic applications. A glancing angle of 87° is employed to grow films of different thicknesses, which are then exposed to post-growth annealing. Detailed local probe analyses in terms of morphology and work function of WOx films are carried out to investigate thickness-dependent

• property modulations of the as-deposited and annealed films. The analyses show a reasonably good correlation with photoelectron spectroscopic measurements on the films and the bulk I–V characteristics acquired on a series of WOx/p-Si heterojunction diodes. The presence of a critical WOx thickness is

Determining by Raman spectroscopy the average thickness and N-layer-specific surface coverages of MoS₂ thin films with domains much smaller than the laser spot size

• Felipe Wasem Klein,
• Jean-Roch Huntzinger,
• Vincent Astié,
• Damien Voiry,
• Romain Parret,
• Houssine Makhlouf,
• Sandrine Juillaguet,
• Jean-Manuel Decams,
• Sylvie Contreras,
• Périne Landois,
• Ahmed-Azmi Zahab,
• Jean-Louis Sauvajol and
• Matthieu Paillet

Beilstein J. Nanotechnol. 2024, 15, 279–296, doi:10.3762/bjnano.15.26

• Raman spectroscopy is a widely used technique to characterize nanomaterials because of its convenience, non-destructiveness, and sensitivity to materials change. The primary purpose of this work is to determine via Raman spectroscopy the average thickness of MoS2 thin films synthesized by direct liquid

• growth of wafer-scale MoS2 thin films on SiO2/Si substrates by direct liquid injection pulsed-pressure chemical vapor deposition (DLI-PP-CVD) using low-toxicity precursors [27]. Such MoS2 thin films showed good stoichiometry (Mo/S = 1.94–1.95) and the potential for high photoluminescence quantum yield

• develop and validate an approach for determining the average thickness of such sub-laser spot size inhomogeneous MoS2 thin films using Raman spectroscopy. First, we reassess here as a ground work the information that can be derived from the Raman spectra of MoS2 flakes for the evaluation of their

Ultrasensitive and ultrastretchable metal crack strain sensor based on helical polydimethylsiloxane

• Shangbi Chen,
• Dewen Liu,
• Weiwei Chen,
• Huajiang Chen,
• Jiawei Li and
• Jinfang Wang

Beilstein J. Nanotechnol. 2024, 15, 270–278, doi:10.3762/bjnano.15.25

• and stretchable strain sensors with an impressive GF exceeding 42000 at a strain level of 150% [24]. These sensors were created by utilizing precisely controlled cracks in CNT films, which were formed through laser engraving of a CNT paper. In their study, Lee et al. have developed a strain sensor

• was exerted on the surface of the Au film at a rate of 10% strain per second, resulting in the initiation and propagation of cracks. Following the release of the pre-stretch, the Au thin films were affixed to silver wires using silver paste at both ends. Ultimately, the surface of the helix was coated

Design, fabrication, and characterization of kinetic-inductive force sensors for scanning probe applications

• August K. Roos,
• Ermes Scarano,
• Elisabet K. Arvidsson,
• Erik Holmgren and
• David B. Haviland

Beilstein J. Nanotechnol. 2024, 15, 242–255, doi:10.3762/bjnano.15.23

• larger than the geometric (electromagnetic) inductance in thin films and nanowires made of amorphous superconductors [16]. It is, therefore, useful in applications that require compact microwave resonators with low loss [17], including microwave filters [18] and resonant radiation detectors [19]. Large

• with 600 nm low-stress (<100 MPa) Si-N films. The sensor chips are 1.6 mm by 3.4 mm, about the size of a standard AFM cantilever chip. The steps are as follows: (a) Superconducting film. We first deposit a 15 nm thick thin film of superconducting Nb60Ti40N by reactive co-sputtering from separate

Ion beam processing of DNA origami nanostructures

• Leo Sala,
• Agnes Zerolová,
• Violaine Vizcaino,
• Alain Mery,
• Alicja Domaracka,
• Hermann Rothard,
• Philippe Boduch,
• Dominik Pinkas and
• Jaroslav Kocišek

Beilstein J. Nanotechnol. 2024, 15, 207–214, doi:10.3762/bjnano.15.20

• the direction of the primary ion’s initial momentum. Hillock structures are usually formed upon such interaction with single-crystal materials [19], while craters and particle tracks form on polymeric thin films such as PMMA [20][21]. The dimensions of such features can be influenced by the interplay

• created by the 56Fe10+ ions. In experiments where the surface was fully covered, such as in the work of Thomaz et al. on 2 nm thick PMMA films on Si irradiated with 1.1 GeV Au atoms (∼5.6 MeV/u) [41], the number of incident ions to the number of craters is 1:1. We expect the same behavior in the present

Graphene removal by water-assisted focused electron-beam-induced etching – unveiling the dose and dwell time impact on the etch profile and topographical changes in SiO₂ substrates

• Aleksandra Szkudlarek,
• Jan M. Michalik,
• Inés Serrano-Esparza,
• Zdeněk Nováček,
• Veronika Novotná,
• Piotr Ozga,
• Czesław Kapusta and
• José María De Teresa

Beilstein J. Nanotechnol. 2024, 15, 190–198, doi:10.3762/bjnano.15.18

• graphene films, each with its own set of advantages and disadvantages. Most of the current techniques are based on multistep processing. For example, ultranarrow graphene nanoribbons can be formed with the so-called meniscus-mask lithography [7] or nanospheres lithography [8], although positioning and