Ultrathin hydrophobic films based on the metal organic framework UiO-66-COOH(Zr)

• Miguel A. Andrés,
• Clemence Sicard,
• Christian Serre,
• Olivier Roubeau and
• Ignacio Gascón

Beilstein J. Nanotechnol. 2019, 10, 654–665, doi:10.3762/bjnano.10.65

• chloride (CPVC) CHC-15 crystal holders from Inficon inside a stainless steel cell with a total volume about 200 mL. Two 9 MHz AT-cut QCM crystals (Inficon) are used in each experiment, where one uncoated disk is used as a reference to correct possible frequency drifts mainly due to temperature or gas flow

Biological and biomimetic surfaces: adhesion, friction and wetting phenomena

• Stanislav N. Gorb,
• Kerstin Koch and
• Lars Heepe

Beilstein J. Nanotechnol. 2019, 10, 481–482, doi:10.3762/bjnano.10.48

• collected articles are devoted to surface-related effects in engineered surfaces, such as multilayered composites, carbon nanofibers, textured steel surfaces, and micropatterned elastomer surfaces. Three articles present recent work on the development of a novel fabrication technique for biomaterials and of

One-step nonhydrolytic sol–gel synthesis of mesoporous TiO₂ phosphonate hybrid materials

• Yanhui Wang,
• P. Hubert Mutin and
• Johan G. Alauzun

Beilstein J. Nanotechnol. 2019, 10, 356–362, doi:10.3762/bjnano.10.35

• mmol), acetophenone (1.44 g, 12.00 mmol), C8H17PO3Et2 (0 mmol, 0.24 mmol, 0.60 mmol, 1.20 mmol, or 2.40 mmol) and toluene (8.0 mL) were mixed in a stainless steel digestion vessel with a PTFE lining (23 mL). The sealed autoclave was heated in an oven at 200 °C for 12 h under autogenous pressure. After

A Ni(OH)₂ nanopetals network for high-performance supercapacitors synthesized by immersing Ni nanofoam in water

• Donghui Zheng,
• Man Li,
• Yongyan Li,
• Chunling Qin,
• Yichao Wang and
• Zhifeng Wang

Beilstein J. Nanotechnol. 2019, 10, 281–293, doi:10.3762/bjnano.10.27

• nickel hydroxide without binders has become a hot topic in recent years. For instance, Ni(OH)2 active materials have been loaded on stainless steel [21], carbon foam [22] and three-dimensional (3D) graphite foam [23]. Furthermore, 3D porous nickel materials have been used extensively as conductive

Sputtering of silicon nanopowders by an argon cluster ion beam

• Xiaomei Zeng,
• Vasiliy Pelenovich,
• Zhenguo Wang,
• Wenbin Zuo,
• Sergey Belykh,
• Alexander Tolstogouzov,
• Dejun Fu and
• Xiangheng Xiao

Beilstein J. Nanotechnol. 2019, 10, 135–143, doi:10.3762/bjnano.10.13

• by plasma arc techniques). The Si nanopowder was pressed into pellets with a diameter of 17 mm and thickness of 160–290 µm at different loads during 10 min by a mechanical press. Then, the pellets were cut into 5 × 5 mm2 samples and mounted on a steel substrate holder of the same size. Since in the

Graphene–graphite hybrid epoxy composites with controllable workability for thermal management

• Idan Levy,
• Eyal Merary Wormser,
• Maxim Varenik,
• Matat Buzaglo,
• Roey Nadiv and
• Oren Regev

Beilstein J. Nanotechnol. 2019, 10, 95–104, doi:10.3762/bjnano.10.9

• ) operated in cone and plate arrangements (stainless steel cone, with a 40 mm diameter and a 4° cone angle) at 25 °C. The shear rate was swept between 0.01–100 1/s, and each measurement was performed at steady-state flow at a shear rate of 0.01 1/s to extract the viscosity [51][68]. Functional thermal

Zn/F-doped tin oxide nanoparticles synthesized by laser pyrolysis: structural and optical properties

• Florian Dumitrache,
• Iuliana P. Morjan,
• Elena Dutu,
• Ion Morjan,
• Claudiu Teodor Fleaca,
• Monica Scarisoreanu,
• Alina Ilie,
• Marius Dumitru,
• Cristian Mihailescu,
• Adriana Smarandache and
• Gabriel Prodan

Beilstein J. Nanotechnol. 2019, 10, 9–21, doi:10.3762/bjnano.10.2

• case, the bandgap values decreased with increasing metal dopant content, down to 3.93 eV for 4 atom % Nd [24]. The FTO films were also successfully tested for other applications such as anticorrosive coatings on steel for fuel cell bipolar plates [25], sensors for liquefied petroleum gas [26

The effect of flexible joint-like elements on the adhesive performance of nature-inspired bent mushroom-like fibers

• Elliot Geikowsky,
• Serdar Gorumlu and
• Burak Aksak

Beilstein J. Nanotechnol. 2018, 9, 2893–2905, doi:10.3762/bjnano.9.268

• a steel sphere for easy alignment. d) Directions defined for the LDP tests, where gripping direction slides in favor of the actual deformation of the fibers, whereas in releasing the sliding slides against the bending of the fibers. Fabrication sequence of bent fibers. a) Metal sphere brought in

Biomimetic surface structures in steel fabricated with femtosecond laser pulses: influence of laser rescanning on morphology and wettability

• Camilo Florian Baron,
• Alexandros Mimidis,
• Daniel Puerto,
• Evangelos Skoulas,
• Emmanuel Stratakis,
• Javier Solis and
• Jan Siegel

Beilstein J. Nanotechnol. 2018, 9, 2802–2812, doi:10.3762/bjnano.9.262

• allows fabrication of specific micro- and nanostructures over extended areas. In this work, we exploit this approach to fabricate complex biomimetic structures on the surface of steel 1.7131 formed upon irradiation with high repetition rate femtosecond laser pulses. In particular, the fabricated

• surface structures; laser rescanning; steel; wettability; Introduction Complex structures found in nature often present properties that are attractive for applications in science and technology. The hydrophobicity found at the lotus leaf surface [1], the exceptional adhesion capability of gecko feet [2

• surface morphology. We present experimental results of complex self-organized structures produced in commercial steel that resemble the morphology of the skin of certain reptiles and insects, which are of great interest due to their exceptional fluid transport and friction reduction properties. Surface

Magnetic and luminescent coordination networks based on imidazolium salts and lanthanides for sensitive ratiometric thermometry

• Pierre Farger,
• Cédric Leuvrey,
• Mathieu Gallart,
• Pierre Gilliot,
• Guillaume Rogez,
• João Rocha,
• Duarte Ananias,
• Pierre Rabu and
• Emilie Delahaye

Beilstein J. Nanotechnol. 2018, 9, 2775–2787, doi:10.3762/bjnano.9.259

• (L)(ox)(H2O)] were obtained with Ln = Eu3+, Gd3+, Tb3+, Dy3+, Ho3+ and Yb3+ by reacting a water/ethanol solution of the lanthanide nitrate and oxalic acid (H2ox) with [HL]. The mixture was sealed in a Teflon-lined stainless steel autoclave and heated at 393 K for 72 h. After cooling to room

• /ethanol solution (1.5 mL). The solution was sealed in a Teflon-line stainless steel bomb (6 mL) and heated at 393 K for 72 h. After cooling to room temperature, the bomb was opened and colorless crystals were filtered and washed with ethanol and dried at room temperature. Yields were between 41% and 59

Optimization of Mo/Cr bilayer back contacts for thin-film solar cells

• Nima Khoshsirat,
• Fawad Ali,
• Vincent Tiing Tiong,
• Mojtaba Amjadipour,
• Hongxia Wang,
• Mahnaz Shafiei and
• Nunzio Motta

Beilstein J. Nanotechnol. 2018, 9, 2700–2707, doi:10.3762/bjnano.9.252

• such as glass or stainless steel [17][18][19][20][21]. Cr forms an oxide interface layer by scavenging the oxygen available on the glass surface during the sputtering process. This creates nucleation centers and promotes nucleation of the next deposited material (in this case Mo), leading to a strong

• adhesion of Mo to the substrates [22][23][24]. The Mo/Cr back contact has been already proposed in flexible thin-film solar cells on metallic foils and stainless steel [25][26][27][28]. However, in these reports Cr was used as a barrier layer to reduce/prevent impurity out-diffusion from the metallic

Characterization of the microscopic tribological properties of sandfish (Scincus scincus) scales by atomic force microscopy

• Weibin Wu,
• Christian Lutz,
• Simon Mersch,
• Richard Thelen,
• Christian Greiner,
• Guillaume Gomard and
• Hendrik Hölscher

Beilstein J. Nanotechnol. 2018, 9, 2618–2627, doi:10.3762/bjnano.9.243

• their skin [2][3][6][7][8][9]. This contradicts everyday experience because a tiny grain of sand easily scratches practically any technical surface even hard ones such as glass or steel. The widely applied sandblasting, for example, is based on this effect. The sandfish, however, moults its skin only

• is indeed lower than those of other technical surfaces such as aluminium (θ = 25°), steel (θ = 26°) or Teflon (θ = 35°), which were examined with the same sand and setup [3]. Interestingly, granular friction angles reported for closely related but not sand-swimming lizards such as the banded skink

• caught between the body and the rest of the sand, leading to a classical three-body abrasion system. Previous studies based on the granular approach indicated that sandfish skin got less damage and resisted wear much better than Teflon, glass or even steel [3][7][8]. We, therefore, investigated the

Friction reduction through biologically inspired scale-like laser surface textures

• Johannes Schneider,
• Vergil Djamiykov and
• Christian Greiner

Beilstein J. Nanotechnol. 2018, 9, 2561–2572, doi:10.3762/bjnano.9.238

• scales found on lizards and snakes, has come to the attention of tribologists. Here, we present results of the lubricated and unlubricated performance of biologically inspired scale-like textures applied with laser light to the surface of bearing steel pins. These were paired in unidirectional sliding

• biologically inspired surface morphology has the potential to reduce friction forces by more than 80%. However, under certain conditions, especially for slow-moving lubricated steel-on-steel and steel-on-ceramic contacts, these surface morphologies may increase friction as well. Similar to classical laser

• . In contrast, our own previous work aimed at retaining the advantages of using laser light to generate a morphological scale-like surface texture [23]. We successfully textured bearing steel surfaces with scale-like morphological patterns and were able to reduce dry friction forces by more than 40

Effect of electrospinning process variables on the size of polymer fibers and bead-on-string structures established with a 2³ factorial design

• Paulina Korycka,
• Adam Mirek,
• Katarzyna Kramek-Romanowska,
• Marcin Grzeczkowicz and
• Dorota Lewińska

Beilstein J. Nanotechnol. 2018, 9, 2466–2478, doi:10.3762/bjnano.9.231

• in ethanol 96% (w/w), purchased from Polmos (Poland), were made with the following concentrations: 8% (w/w), 12% (w/w), 14% (w/w), and 20% (w/w). Electrospinning setup The weighted portion of PVP solution was delivered to a steel nozzle with an infusion pump. The nozzle had an inner diameter of 0.6

Droplet-based synthesis of homogeneous magnetic iron oxide nanoparticles

• Christian D. Ahrberg,
• Ji Wook Choi and
• Bong Geun Chung

Beilstein J. Nanotechnol. 2018, 9, 2413–2420, doi:10.3762/bjnano.9.226

• steel reactor has been used by Laura Uson et al. for the synthesis of magnetic nanoparticles through a thermal decomposition reaction [24]. Microfluidic reactions can be operated using continuous flow or segmented flow. While single-phase continuous flow is simpler to operate, the laminar flow profile

Nanotribology

• Enrico Gnecco,
• Susan Perkin,
• Andrea Vanossi and
• Ernst Meyer

Beilstein J. Nanotechnol. 2018, 9, 2330–2331, doi:10.3762/bjnano.9.217

• including nanodiamonds [1] and novel materials such as nitrogen-doped graphene oxide [2] and imidazolium-based ionic liquids [3] used as additives to mineral oils. Standard large-scale applications to steel surfaces, but also to a material of key importance in micro- and nanoelecromechanical systems, i.e

• ., silicon oxide, are recognized. The quality of the surface condition is addressed experimentally by the example of cryogenically treated martensitic stainless steel [4] and theoretically by an analysis of the influence of micro-dimple textures on hydrodynamic lubrication [5]. On a more fundamental level

Electrospun one-dimensional nanostructures: a new horizon for gas sensing materials

• Muhammad Imran,
• Nunzio Motta and
• Mahnaz Shafiei

Beilstein J. Nanotechnol. 2018, 9, 2128–2170, doi:10.3762/bjnano.9.202

• inside a stainless steel needle. The electrospinning setup and resulting hollow fibers are shown in Figure 5. Choi et al. [75] synthesized macroporous WO3 NTs using coaxial electrospinning combined with sacrificial templating. A porous structure using colloidal polystyrene (PS) particles in a solution

Synthesis of carbon nanowalls from a single-source metal-organic precursor

• André Giese,
• Sebastian Schipporeit,
• Volker Buck and
• Nicolas Wöhrl

Beilstein J. Nanotechnol. 2018, 9, 1895–1905, doi:10.3762/bjnano.9.181

• the various deposition parameters on the growth. Silicon, stainless steel, nickel and copper are used as substrate materials. The CNWs deposited are characterized by scanning electron microscopy (SEM), Raman spectroscopy and Auger electron spectroscopy (AES). The combination of bias voltage, the

• substrate bias and the substrate temperature on the deposition process and on the structure of the synthesized CNWs. Four different kinds of substrates were chosen: stainless steel, aluminium, nickel and silicon. These materials were chosen because they differ significantly in essential properties such as

• found that the described growth model is also valid for all of the chosen materials. However, the growth regimes are shifted for the different materials. While all of the above mentioned structures are found on stainless steel and aluminium (although shifted to different bias voltage and temperature

Magnetic properties of Fe₃O₄ antidot arrays synthesized by AFIR: atomic layer deposition, focused ion beam and thermal reduction

• Juan L. Palma,
• Alejandro Pereira,
• Raquel Álvaro,
• José Miguel García-Martín and
• Juan Escrig

Beilstein J. Nanotechnol. 2018, 9, 1728–1734, doi:10.3762/bjnano.9.164

• 200 °C in stop/exposure-mode. The ferrocene (FeCp2) was held in a stainless-steel container (bottle) heated to 90 °C to ensure sufficient vapor pressure. The pulse times of ferrocene and ozone in the FeCp2/O3 cycle were 2 s and 0.2 s, respectively; the exposure and pump times were 5 s and 15 s

Multimodal noncontact atomic force microscopy and Kelvin probe force microscopy investigations of organolead tribromide perovskite single crystals

• Yann Almadori,
• David Moerman,
• Jaume Llacer Martinez,
• Philippe Leclère and
• Benjamin Grévin

Beilstein J. Nanotechnol. 2018, 9, 1695–1704, doi:10.3762/bjnano.9.161

• inverse temperature solubility. The single crystal investigated under ultrahigh vacuum (UHV) was fixed on a stainless steel sample UVH holder with a compatible electrically conductive silver epoxy paste (EPO-TEK E4110), which was cured at room temperature (RT) over 24 hours. The sample was subsequently

Sheet-on-belt branched TiO₂(B)/rGO powders with enhanced photocatalytic activity

• Huan Xing,
• Wei Wen and
• Jin-Ming Wu

Beilstein J. Nanotechnol. 2018, 9, 1550–1557, doi:10.3762/bjnano.9.146

• transferred to a Teflon-lined stainless steel autoclave and maintained at 200 °C for 24 h, with a heating rate of 2 °C/min. After the reaction, the precipitates were centrifugally washed with distilled water three times and then immersed in a 0.1 M HCl solution for 1 h repetitively for three times to complete

Scanning speed phenomenon in contact-resonance atomic force microscopy

• Christopher C. Glover,
• Jason P. Killgore and
• Ryan C. Tung

Beilstein J. Nanotechnol. 2018, 9, 945–952, doi:10.3762/bjnano.9.87

• system measures) of the contact becomes The presence of the fluid stiffness kf introduces an error in the AFM measurement of the sample stiffness. This error is dependent on the relative magnitudes between ks and kf. Experimental A sample of high-grade mica was mounted to a steel puck using

Cyclodextrin inhibits zinc corrosion by destabilizing point defect formation in the oxide layer

• Abdulrahman Altin,
• Maciej Krzywiecki,
• Adnan Sarfraz,
• Cigdem Toparli,
• Claudius Laska,
• Philipp Kerger,
• Aleksandar Zeradjanin,
• Karl J. J. Mayrhofer,
• Michael Rohwerder and
• Andreas Erbe

Beilstein J. Nanotechnol. 2018, 9, 936–944, doi:10.3762/bjnano.9.86

• inhibitors [8][12][13]. Metallic zinc is industrially used for cathodic protection of steel [15]. In this work, the inhibition of zinc corrosion by β-CD was investigated electrochemically. Inhibition efficiencies were determined by electrochemical impedance spectroscopy (EIS). After exposure to chloride

Graphene composites with dental and biomedical applicability

• Sharali Malik,
• Felicite M. Ruddock,
• Adam H. Dowling,
• Kevin Byrne,
• Wolfgang Schmitt,
• Ivan Khalakhan,
• Yoshihiro Nemoto,
• Hongxuan Guo,
• Lok Kumar Shrestha,
• Katsuhiko Ariga and
• Jonathan P. Hill

Beilstein J. Nanotechnol. 2018, 9, 801–808, doi:10.3762/bjnano.9.73

• was hand-mixed with all the poly(acrylic acid) solution for 20 s using a stainless steel spatula, and then the remaining GI powder was added and mixed for a further 20 s. Dynamic viscosity measurements The viscosity of all the poly(acrylic acid) solutions was measured with a digital viscometer

• covered with an acetate strip and aligned using nylon wedges and a locating pin. The hand-mixed GI restorative plastic mass was applied to one side of the split-mould immediately after mixing using the stainless steel spatula and allowed to flow into the mould to minimise air bubble incorporation in the

Combined pulsed laser deposition and non-contact atomic force microscopy system for studies of insulator metal oxide thin films

• Daiki Katsube,
• Hayato Yamashita,
• Satoshi Abo and
• Masayuki Abe

Beilstein J. Nanotechnol. 2018, 9, 686–692, doi:10.3762/bjnano.9.63

• ]. The substrate is fixed with four screws and leaf springs on the ceramic part of the sample holder. Stainless steel electrodes under the ceramic are used as connections for flowing a current through the tungsten thin film. The electrode for the flowing current is insulated from the base of the stocker